English dropdown-ico

Manual KTI Networks KC-300D

21 pages 0.26 mb
Download

Go to site of 21

Summary
  • KTI Networks KC-300D - page 1

    -1- 10/100BASE-TX TO 100BASE-FX MEDIA CONVERTERS KC-300D Series Installation Guide DOC.060215-KC-300D ...

  • KTI Networks KC-300D - page 2

    -2- (C) 2003 KTI Networks Inc. All rights reserved. No part of this documen- tation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without per- mission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from ...

  • KTI Networks KC-300D - page 3

    -3- The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inte ...

  • KTI Networks KC-300D - page 4

    -4- T a ble of Contents 1. Introduction ......................................................... 5 1.1 Key Features ................................................................................. 5 1.2 Specifications ................................................................................ 6 1.3 Optical Specifications .................... ...

  • KTI Networks KC-300D - page 5

    -5- 1. Introduction The 10/100BASE-TX to 100BASE-FX media converter series provides a media conversion allowing high-speed integration of fiber optic and twisted- pair segments. W ith 10BASE-T a nd 100BASE-TX support, the converters provide seamless translation between Ethernet and Fast Ethernet networks. A complete set of LEDs allows for quick sta ...

  • KTI Networks KC-300D - page 6

    -6- 1.2 Specifications T wisted-Pair Interfa ce (TP Por t) Connector Shielded RJ-45 Pin Assignments Auto MDI/MDI-X detection Signal Compliance IEEE 802.3 10BASE-T , 802.3u 100BASE-TX Data Speed 10Mbps or 100Mbps Duplex Mode Half-duplex or Full-duplex Configuration Auto-negotiation capable and optional forced manual settings Ca ble T ypes 10Mbps - C ...

  • KTI Networks KC-300D - page 7

    -7- Fiber Optic Interface (FX Port) Signal Compliance IEEE 802.3u 100BASE-FX Connector SC, ST , MT -RJ, VF-45, LC or Single SC Data Speed 100Mbps Duplex Mode Full-duplex and optional half duplex Ca ble T ypes Multimode (MMF) - 50/125, 62.5/125 µ m Single mode (SMF) - 9/125 µ m Supported Link Distance MMF up to 2km SMF up to 100km Single SMF WDM u ...

  • KTI Networks KC-300D - page 8

    -8- LED Indicators L E D DISPLA Y ST A TE INTERPRET A TION P W R Power status O N Power on O F F Power off TP LINK T P port link status O N Link up and no traffic O F F Link fault Blink Rx/Tx activities TP 100M TP port speed status O N 100Mbps O F F 10Mbps TP F DX TP port duplex status O N Full duplex O F F Half duplex Blink Collisions on half dupl ...

  • KTI Networks KC-300D - page 9

    -9- Basic Information Forwarding Throughput Full wire speed at 100M full duplex 10Mbps - 14,880 pps at 64-byte packets 100Mbps - 148,800pps at 64-byte packets Packet T ype s Transparent and no modification for - IEEE 802.3 standard packets - IEEE 802.1Q VLAN tagged packets Packet Length U p t o 1522 bytes at store-and-forward mode No limit at smart ...

  • KTI Networks KC-300D - page 10

    -10- 1.3 Optical Specifications The media converter series provides the following fiber options: Duplex Fiber Series Model Port Fiber W avelength Tx Power Rx Sensitivity 300D-T ST M M F 1310nm -19 ~ -14dBm -31dBm 300D-C S C M M F 1310nm -19 ~ -14dBm -31dBm 300D-EC S C M M F 1310nm -20 ~ -14dBm -31dBm 300D-JM MT -R J M MF 1310nm -19 ~ -14dBm -31dBm ...

  • KTI Networks KC-300D - page 11

    -11- 1.4 Special Functions Auto MDI/MDI-X Function This function allows the TP port to auto-detect the twisted-pair signals and adapts itself to form a valid MDI to MDI-X connection with the remote connected device automatically . Auto-negotiation Function When TP port is set on Auto-negotiation mode (SW1:ON), it is featured with auto-negoti ation ...

  • KTI Networks KC-300D - page 12

    -12- Link Fault Pass Through Function When this function is enabled, a link fault detected on the TP port will force a link down on the FX port. Si milarly , a link fault detected on the FX port will also force a link down on the TP port. As illustrated in the following figure, this function allows to pass TP link fault to the remote link partner a ...

  • KTI Networks KC-300D - page 13

    -13- 2. Installation 2.1 Unpacking Check that the following components have been included: • Installation guide (or contained in the product CD) • 10/100 Media Converter • One AC power adapter If any item is found missing or damaged, please contact your local reseller for replacement. 2.2 Mounting the Device Desktop Mounting The media convert ...

  • KTI Networks KC-300D - page 14

    -14- 2.3 Applying Power Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area. The AC Power Adapter Specifications AC input power: AC power voltage of your area, options - Rated AC120V/ ...

  • KTI Networks KC-300D - page 15

    -15- 2.4 Making TP Port Connection TP port is featured to support connection to : • Auto-negotiation devices • Auto-negotiation incapable 10BASE-T devices • Auto-negotiation incapable 100BASE-TX devices Network Cables 10BASE-T : 2-pair UTP Cat. 3,4,5 , EIA/TIA- 568 100-ohm STP 100BASE-TX: 2-pair UTP Cat. 5, EIA/TIA-568 100-ohm STP Link distan ...

  • KTI Networks KC-300D - page 16

    -16- 2.5 Ma king FX Port Connection FX port operates on 100Mbps a nd full duplex (fa ctory default). A variety of fiber options is provided as follows: Duplex Fiber Series Model Connector W avelength Fiber Ref. dista nce 300D-T ST 1310nm Duplex MMF 2 k m 300D-C S C 1310nm Duplex MMF 2 k m 300D-JM M T - RJ 1310nm Duplex MMF 2 k m 300D-VM VF-45 1310n ...

  • KTI Networks KC-300D - page 17

    -17- Single Fiber Bi-Di W DM Serie s Model Connector W avelength Fiber Ref. Dista nce 300D-W3515 Bi-Di SC Tx 1310nm Single SMF 15 - 20km Rx 1550nm 300D-W5315 Bi-Di SC Tx 1550nm Single SMF 15 - 20km Rx 1310nm 300D-W3540 Bi-Di SC Tx 1310nm Single SMF 40km Rx 1550nm 300D-W5340 Bi-Di SC Tx 1550nm Single SMF 40km Rx 1310nm Since the W DM single fiber me ...

  • KTI Networks KC-300D - page 18

    -18- 2.6 LED Indicators Link Fault Pass Through Function is disabled LED Display Status Interpretation P W R Power status On Power on O ff Power off TP LINK T P port link status On Link up and no traffic O f f Link fault Blink Rx/Tx activities TP 100M T P port speed status O n 100Mbps O f f 10Mbps T P F DX TP port duplex status On Full duplex O f f ...

  • KTI Networks KC-300D - page 19

    -19- 3. Option al Configuration Settings The media converter provide s a dditional configuration settings which are user-inaccessible. The settings are built on the board inside the prod- uct case. The settings are provided for technical installers to adapt the converter to fit some specific application needs. 3.1 User Inaccessible Jumpers The sett ...

  • KTI Networks KC-300D - page 20

    -20- 3.1.1 Forwarding Mode Setting JP1 The following table lists the forward method used in different TP to FX conversions: JP1 Setting TP port to/from FX port Forward method Store-and-forward 10BASE-T to 100BASE-FX Store and forward 100BASE-TX to 100BASE-FX Store and forward Smart-forward 10BASE-T to 100BASE-FX Store and forward 100BASE-TX to 100B ...

  • KTI Networks KC-300D - page 21

    -21- 3.1.2 802.3x Function Setting JP2 IEEE 802.3x function is the flow control method used for full duplex op- eration on TP port and FX port under store and forward mode. This method uses pause frames for one port to stop further transmission from its link partner . 3.1.3 FX Duplex Setting JP3 This setting is used to set the duplex mode of the FX ...

Manufacturer KTI Networks Category TV Converter Box

Documents that we receive from a manufacturer of a KTI Networks KC-300D can be divided into several groups. They are, among others:
- KTI Networks technical drawings
- KC-300D manuals
- KTI Networks product data sheets
- information booklets
- or energy labels KTI Networks KC-300D
All of them are important, but the most important information from the point of view of use of the device are in the user manual KTI Networks KC-300D.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals KTI Networks KC-300D, service manual, brief instructions and user manuals KTI Networks KC-300D. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product KTI Networks KC-300D.

Similar manuals

A complete manual for the device KTI Networks KC-300D, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use KTI Networks KC-300D by users. Manuals are usually written by a technical writer, but in a language understandable to all users of KTI Networks KC-300D.

A complete KTI Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual KTI Networks KC-300D - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the KTI Networks KC-300D, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the KTI Networks KC-300D, that we can find in the current document
3. Tips how to use the basic functions of the device KTI Networks KC-300D - which should help us in our first steps of using KTI Networks KC-300D
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with KTI Networks KC-300D
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of KTI Networks KC-300D in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning KTI Networks KC-300D?

Use the form below

If you did not solve your problem by using a manual KTI Networks KC-300D, ask a question using the form below. If a user had a similar problem with KTI Networks KC-300D it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)