-
Raypak 120 - page 1
...
-
Raypak 120 - page 2
2 Subject to technical changes! Slight changes may be made to the illustrations, process steps and technical data as a result of our policy of continuous improvement. About these instructions These Installation Instructions contain important information for the safe and professional installation, start-up and maintenance of the boiler with boiler c ...
-
Raypak 120 - page 3
3 CONTENTS 1 - W ARNINGS 4 PA Y ATTENTION T O THESE TERMS 4 2 - GENERAL SAFETY 6 TIME/TEMPERA TURE RELA TIONSHIPS IN SCALDS 6 3 - BEFORE INST ALLA TION 6 4 - REGULA TIONS AND GUIDELINES 7 5 - INTRODUCTION 8 TECHNICAL DATA 1 0 PRINCIPLE COMPONENTS 12 MODE OF OPERATION (AT REST) 12 MODE OF OPERATION 12 SAFETY DEVICES 12 BANNED MA TERIAL ST A TEMENT 1 ...
-
Raypak 120 - page 4
4 CAUTION : This boiler requires forced w ater circulation when the burner is operating. See minimum and maximum flow rates. Severe damage will occur if the boiler is operated without proper water flow circulation. NOTE : Minimum 18 A WG, 105°C, stranded wire m ust be used for all low voltage (less than 30 volts) external connections to the unit. ...
-
Raypak 120 - page 5
5 Observe these instructions as general warnings: – Chemicals used to clean the system and/or inhibit corrosion must be pH neutral, i.e. they should ensure that the level of the pH in the system water remains neutral. Premature failure of certain components can occur if the pH level in the system water is out of normal levels. – Raypak recommen ...
-
Raypak 120 - page 6
6 3 - BEFORE INST ALLA TION Raypak strongly recommends that this manual be reviewed thoroughly bef ore installing your XP ak boiler. Please revie w the Gener al Safety information before installing the boiler . F actor y warranty does not apply to boilers that have been improperly installed or operated. (Refer to the warranty at the back of this ma ...
-
Raypak 120 - page 7
7 Ratings and Certifications Standards: • Gas fired hot water boiler for either direct vent installation or for installation using indoor combustion air . Design according to: ANSI Z21.13b 2007 – CSA 4.9b 2007 – Fired low pressure hot water boilers . Categor y IV . • SCAQMD Rule 1146.2 All Raypak boilers are National Board Approved, and des ...
-
Raypak 120 - page 8
8 XP AK 85 Fig. 1 G F R P C 5 - INTRODUCTION The XPak boiler is a wall hung, fan assisted, direct vent, heating boiler only . These boilers – by design – incorporate electronic ignition, circulating pump, pressure relief valve, pressure gauge, and automatic bypass. As supplied, the boiler will automatically modulate to provide central heating o ...
-
Raypak 120 - page 9
9 Fig. 1A A Pressure gauge B Green led C 2-digit LED display D Red led E T emperature selector space heating F Mode selector switch G T emperature selector Domestic Hot Water F Off/reset - Select this position when the boiler needs to be reset or switched off. Summer mode - The domestic hot water function provided by the water tank is activ ated. T ...
-
Raypak 120 - page 10
10 TECHNICAL DA T A Tab. 1 XPak 85 XPak 120 Input - Output Input - (0 - 2000 ft / 0 - 610 m) Btu/hr 25,600 - 87,000 27,300 - 119,500 k W 7.5 - 25.5 8.0 - 35.0 Input - (2000 - 4500 ft / 610 - 1375 m) Btu/hr 25,600 - 82,900 27,300 - 114,300 k W 7.5 - 24.3 8.0 - 33.5 Output (176°F - 86°F / 80°C - 30°C) Btu/hr 25,200 - 76,600 26,600 - 108,300 k W 7 ...
-
Raypak 120 - page 11
11 XPak 85 XPak 120 Boiler flue gas connection i n 2 3/8 2 3/8 m m 60 60 Combustion air connection outer dia. i n 4 4 m m 100 100 Free fan unit feed pressure in w . c. 0.26 0.18 Pa 65 45 Flue gas mass flow rate at rated full load (A) lbs/hr 90.39 123.17 kg/hr 4 1 55.87 Flue gas mass flow rate at rated full load (E) lbs/hr 88.89 121.18 kg/hr 40.32 5 ...
-
Raypak 120 - page 12
12 BANNED MA TERIAL ST A TEMENT : No banned materials or substances have been used in the manufacture or production of this appliance or its inherent components MANUAL HANDLING ST A TEMENT : CAUTION: This appliance may require 2 or more persons to lift or carry it to the installation location; due to the weight of the appliance it may be necessary ...
-
Raypak 120 - page 13
13 PIPING CONNECTIONS (FIG. 3) Legend A - boiler in connection 3/4” NPT - male B - boiler out connection 3/4” NPT - male C - gas supply connection 3/4” NPT - female D - pressure relief valve drain connection 3/4” NPT - female E - condensate connection Ø (rubber flexible) 0.825” (21 mm) female F - boiler drain valve - open-ended spanner d ...
-
Raypak 120 - page 14
14 Minimum Clearances to Combustibles T op=0 F ront =0 AL, CL Rear=0 Left=0 Right=0 AL = Alcove CL = Closet Note: The XPak boiler has passed the zero inches vent clearance to combustibles testing requirements provided by the boiler Harmonize d Standard ANSI Z21.13b 2007 – CSA 4.9b 2007 and therefore is listed for zero clearance to combustibles wh ...
-
Raypak 120 - page 15
15 PACKAGING AND TRANSPORT A TION 1. SCOPE OF DELIVERY The boiler is delivered fully assembled. - When receiving the deliv er y , check if the pac kaging is intact. - Check that all the items listed in T able 2 are included in the deliv er y . 2. TRANSPORTING THE BOILER CAUTION: The boiler ma y be damaged when it is improper ly secured. - Only tran ...
-
Raypak 120 - page 16
16 NOTICE: To prevent combustion air contamination when considering exhaust vent and intake air vent termination. Intake and exhaust may be vented vertically through the roof or out a side wall. The intake and exhaust venting methods are detailed in the Venting Section. Do not attempt to install the XPak Boiler using any other means. Be sure to loc ...
-
Raypak 120 - page 17
17 2. PLACING THE WALL-MOUNTED XPAK BOILER XPak boilers are wall mounted. Use only the XPak boiler wall mounting instructions included in the box. WARNING: The wall must be capable of carrying the weight of the boiler and its related components. The weights of the boiler are approximately: XPak 85 = 82 lbs (37 kg). XPak 120 = 93 lbs (42 kg). Failur ...
-
Raypak 120 - page 18
18 required system volume and capacity, no valve is to be placed between the boiler and the expansion tank. 6. Install an Air Elimination Device on the system supply if required, the boiler has two auto air vents built in. 7. Install a drain valve at the lowest point of the system. Note: The XPak has a proper internal drain valve. (see Fig. 42a) 8. ...
-
Raypak 120 - page 19
19 XPAK INST ALLA TION DIAGRAMS NOTICE: The f ollowing illustrations are simplified conceptual illustrations only . Key for installation sample diagrams 1. XPak boiler 2. Gas shut off valve 3. Expansion vessel 4. Radiators 5. Under floor heating 6. Pressure relief valve discharge pipe 7. Indirect DHW tank 8. 3-way valve 9. Room thermostat (24V) 10. ...
-
Raypak 120 - page 20
20 Fig. 10 Fig. 9 ...
-
Raypak 120 - page 21
21 Fig. 11 Fig. 12 ...
-
Raypak 120 - page 22
22 NOTICE: When installing the gas supply connection, it must comply with local regulations or , if such regulations do not exist, with the National Fuel Gas Code, ANSI Z 223.1. In Canada, the gas supply connection must comply with local regulations or , if such regulations do not exist, with CAN/CSA B149, Natural Gas and Propane Installation Code. ...
-
Raypak 120 - page 23
23 BOILER TEMPLA TE (Fig. 15) W all Mounting Information XP ak comes with a template, which allows you to easily mark the location of the screws for the mounting bracket and the location of the flue gas pipe on the wall (Raypak coaxial PP vent system only). The connection to the gas circuits must be made on site, 3/4” gas cock is supplied with th ...
-
Raypak 120 - page 24
24 COMBUSTION AIR AND VENTILA TION OPENINGS Provisions for combustion and ventilation air must be made in accordance with section 5.3, Air for Combustion and Ventilation, of the National Flue Gas Code, ANSI Z223.1, or Sections 7.2, 7.3 or 7.4 of CAN/CGA B149, Installation Codes, or applicable provisions of the local building codes. CAUTION: BOILER ...
-
Raypak 120 - page 25
25 2. BOILER SUPPLY XPak boilers are supplied with the following vent components and they are certified together with the XPak boiler as a constructional unit. - 60/100 mm vent exit ( Fig. 16 pos. 1) - Left side intake air (factory sealed with two screws) for two pipes solutions (Fig. 16 pos. 2) - Right side intake air (factory sealed with two scre ...
-
Raypak 120 - page 26
26 4. MINIMUM CLEARANCES FROM VENT/AIR INLET TERMINATION U.S. Installations1 Canadian Installations2 A Clearance above grade, veranda, porch, deck, or balcony 1 ft (30 cm) 1 ft (30 cm) B Clearance to window or door that may 4 ft (1.2m) below or to side of be opened opening; 1 foot (30 cm) above 3 ft (91 cm) opening C Clearance to permanently closed ...
-
Raypak 120 - page 27
27 Fig. 24 Fig. 23 NOTICE: The following illustrations are simplified conceptual illustrations only . Legend for illustrations 23-24-25-26-27-28-29-30-31-32 Two pipes vent adaptors (included with the boiler) Pos. 1 Mounting Clip (set of 4) 3.94” (100 mm) for coaxial Pos. 2 (Fig. 24) 90° Elbow 3” (80 mm) single wall Pos. 2 (Fig. 25-26-27-28) Ad ...
-
Raypak 120 - page 28
28 Fig. 25 Fig. 26 a = total intake length = INTAKE b = total flue length = EXHAUST a = total intake length = INTAKE b = total flue length = EXHAUST TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION ...
-
Raypak 120 - page 29
29 Fig. 28 Fig. 27 a = total intake length = 0 b = total flue length = EXHAUST a = total intake length = INTAKE b = total flue length = EXHAUST a = 0 TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION TWO PIPES SINGLE WALL ROOM AIR DEPENDENT OPERATION ...
-
Raypak 120 - page 30
30 Stainless Steel 3” Vent System 1 US + CANAD A Vent System - Room Air independent Operation (Sealed Combustion Operation) - Fig. 12-14-15-17 Vent System diameter 3” V ent system material Stainless steel T wo pipes v ent adaptors (included with the boiler) - - adaptor 80 mm > 3” (included with the boiler 1 pcs) for flue - - adaptor 80 mm ...
-
Raypak 120 - page 31
31 Fig. 29 a = total intake length = INTAKE b = total flue length = EXHAUST DESCRIPTION DIA GRAM DRA WING P/N 013040 T wo pipes v ent adaptors Fig. 29-30-31-32 (included with the boiler) P os. 1 P/N 013040 adaptor 80 mm > 3” Fig. 29-30-31-32 (included with the boiler 1 pcs) P os. 2 TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION ...
-
Raypak 120 - page 32
32 Fig. 31 Fig. 30 a = total intake length = INTAKE b = total flue length = EXHA UST TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION a = total intake length = INTAKE b = total flue length = EXHA UST ...
-
Raypak 120 - page 33
33 Fig. 32 TWO PIPES SINGLE WALL SEALED COMBUSTION OPERATION a = total intake length = 0 b = total flue length = EXHA UST ...
-
Raypak 120 - page 34
34 Fig. 34 Fig. 33 B 7 - ELECTRICAL CONNECTIONS De vices such as outdoor sensor, 3-w ay v alve , tank sensor , tank thermostat, remote controls are all connected to the external connection board. The electrical connections to the boiler must be made in accordance with all applicable local codes and the latest revision of the National Electrical Cod ...
-
Raypak 120 - page 35
35 4. CASING REMOV AL (Fig. 33) T o gain inter nal access to the appliance you m ust first remov e the casing, proceed as outlined below: - remov e the 3 screws (B) located at the Left/Right/F ront of the underside of the casing - lift the casing upward to disengage it from the top locating hooks and then remove - store the casing and screws (B) sa ...
-
Raypak 120 - page 36
36 REMOTE CONTR OL EXTERNAL SENSOR 0T+ M4 -t° M2 T ANK THERMOST A T V ROOM THERMOST A T (jumper when not used) T ANK SENSOR -t° M4a M3b M3a M3 UNDERFLOOR HEA TING LIMIT THERMOST A T OR CONDENSA TE PUMP ALARM (jumper when not used) LO W V OL T A GE HIGH V OL T A GE 120V N L F= fuse 4AF PCB fuse=4A T Cod. 20003227 3W BLUE (COMMON) BROWN (CLOSED) BL ...
-
Raypak 120 - page 37
37 12. OUTDOOR SENSOR CONNECTION The user can program the desired supply temperature based on the outdoor temperature. Once the outdoor sensor is connected to the control board, the water temperature of the boiler will adjust to run the boiler more efficiently and provide greater comfort to the living space. Connection Specification – Wire 22 AWG ...
-
Raypak 120 - page 38
38 WIRING FUNCTIONAL DIAGRAM Fig. 40 ...
-
Raypak 120 - page 39
39 8 - ST AR T -UP PROCEDURE There are sev eral steps in volv ed in star ting up the boiler . FOR Y OUR SAFETY READ BEFORE OPERA TING W ARNING : If you do not f ollow these instructions exactly , a fire or explosion may result causing proper ty damage, personal injur y , or loss of life. A. This appliance does not hav e a pilot. It is equipped with ...
-
Raypak 120 - page 40
40 system the pressure gauge will begin to rise. Once the gauge has reached 15 p.s.i. (1 bar) close both valves and begin venting all manual air release valves, starting at the lowest first. It may be necessary to go back and top-up the pressure until the entire system has been filled. Inspect the system for water tightness, fixing any leaks. WARNI ...
-
Raypak 120 - page 41
41 7. CHECK THERMOSTAT CIRCUIT(S) 1. Disconnect the two external wires connected to the boiler thermostat terminals (low voltage terminal strip M4a). 2. Connect a voltmeter across these two incoming wires. Close each thermostat, zone valve and relay in the external circuit one at a time and check the voltmeter reading across the incoming wires. 3. ...
-
Raypak 120 - page 42
42 16. FINAL CHECKS - ENSURE ALL TEST NIPPLES ON THE APPLIANCE GAS V AL- VE ARE TIGHT AND CHECKED FOR TIGHTNESS. - ENSURE THE APPLIANCE FLUE SYSTEM IS INST ALLED CORRECTL Y AND IS PROPERL Y SECURED . - ENSURE ALL PIPE WORK IS RE-CHECKED FOR SOUNDNESS. - REA TT ACH APPLIANCE CASING. - COMPLETE CHECKLIST Complete details of the boiler , controls, ins ...
-
Raypak 120 - page 43
43 10 - ST ART -UP AND OPERA TION XPak wall-mounted condensing boiler is designed for the production of heating and domestic hot water if a storage tank is connected. The control panel contains the main boiler control and manage- ment functions. 1. SWITCHING ON THE APPLIANCE Switch on the boiler as follows: - Open the gas tap under the boiler by tu ...
-
Raypak 120 - page 44
44 Fig. 45 A Pressure gauge B Green led C 2-digit LED display D Red led E T emperature selector space heating F Mode selector switch G T emperature selector Domestic Hot Water* * The par ts of the manual ref er ing to the DHW circuit should be only considered if a indirect water tank with sensor is instal led, case B (Fig. 61) A BC D E F G Domestic ...
-
Raypak 120 - page 45
45 Fig. 46 Fig. 47 DHW mode Heating mode Fig. 48 Fig. 49 Fig. 50 Fig. 51 Fig. 52 Fig. 53 Fig. 54 Fig. 55 Fig. 56 Fig. 57 Closed position B green indicator LED boiler status Open position D red indicator LED fault For AL41 faults If the pressure on the water gauge located on the control panel is less than 7 psi (0.5 bar), proceed as follows: - T ur ...
-
Raypak 120 - page 46
46 5. HEA TING MODE With the selector switch in the ON position ( - - F ) and any additional controls (time clock, prog rammer , room ther mostat, etc,) calling for heat, the appliance will oper ate in the heating mode. The pump and fan will be activ ated via the flow temperature sensor . When the fan is sensed to be operating correctly (blower sig ...
-
Raypak 120 - page 47
47 NOTICE: When the request for heating and/or hot water has been satisfied, the boiler pump and fan may continue to circulate to dissipate any residual heat within the boiler . 7. BOILER F AN SPEEDS The boiler fan speeds require to be checked and/or adjusted prior to making any adjustments to the gas valve or if the main PCB has been replaced. A T ...
-
Raypak 120 - page 48
48 COMPONENT V ALUE F a n 120V AC Pump 120V A C 3-way valve (field supplied) 120V AC Ignition transformer 120V AC Gas valve 120V AC Room thermostat connection 24 Vdc NTC sensor (dry contact) 10Kohm NTC sensor (wet contact) 10Kohm FUNCTION V ALUE Standard Heating Range °F (°C) 104-176 (40-80) Floor Heating Range °F (°C) 68-113 (20-45) CH limited ...
-
Raypak 120 - page 49
49 JUMPER IN POSITION 5: unused JUMPER IN POSITION 6: unused The boiler is supplied standard with the jumper in position 3 (standard heating + indirect water tank with thermostat); if you wish to use an e xternal water tank with sensor , move this jumper from position 3 to position 2 (case B, Fig 61); if you wish to have low temperature for floor s ...
-
Raypak 120 - page 50
50 OUTDOOR TEMPERA TURE RESET CUR VES OUTDOOR RESET CORRECTION NIGHT SETBACK OUTDOOR TEMPERA TURE FLOW TEMPERA TURE Fig. 65 Fig. 66 Fig. 67 68 5 9 5 0 41 3 2 2 3 14 5 -4 212 194 176 158 140 122 104 86 68 OUTDOOR TEMPERA TURE FLOW TEMPERA TURE 86 7 7 6 8 5 9 50 4 1 3 2 23 14 5 -4 194 176 158 140 122 104 86 68 50 10 20 30 40 50 60 70 80 90 -2 0 -15 - ...
-
Raypak 120 - page 51
51 17. F AUL T CODES When the boiler detects a temporary fault condition, the appropriate code is shown flashing on the display . If/when the fault code is final, the pump will perform a 60-second post circulation and the red LED will be illuminated. CODE CA USE ALARM TYPE ACTION AL10 Ignition failure/not flame sensed, Final Reset, check appliance ...
-
Raypak 120 - page 52
52 PUMP ASSEMBL Y (Fig. 69) Locate and remove the 2 securing screws (A) at the rear of the pump assemb ly . Disconnect the flow pipe (B, only for XP ak 120) from the combustion chamber connection, slacken the pipe at the h ydraulic assembly and s wing/rotate clear of the pump assembly . Disconnect and remove the pump outlet pipe (C) from the pump a ...
-
Raypak 120 - page 53
53 W A TER PRESSURE SWITCH (Fig. 69) Locate and remove the screw (I) from the water pressure switch. Remove the wiring. Carefully remove the switch. Replace in the re verse order . FLO W SENSOR (PRIMAR Y THERMIST OR) (Fig. 1) Unclip and remov e the air chamber front cov er. Unclip the primar y thermistor from the flow outlet pipe. Disconnect thermi ...
-
Raypak 120 - page 54
54 MAIN HEA T EXCHANGER (Fig. 76-77) Unclip and remove the three air chamber covers (front, left hand, right hand sides). Disconnect all the wiring connections. Fig. 76: slacken the gas pipe (A) at the air box connection and s wing/rotate of the fan assembly . Disconnect the flow (B) , return (C) and condensation connections on the heat exchanger . ...
-
Raypak 120 - page 55
55 CONDENSA TE TRAP REMO V AL (Fig. 79) Disconnect the 2 upper rubber condensate pipes (A) . Remove the pin (B) that secures the trap to the air box plate. Disconnect the lower rubber condensate pipe (C) from the condensate trap. Carefully remove the condensate trap. Replace in the reverse order . FLUE COLLECT OR AND FLUE THERMOST A T REMO V AL (Fi ...
-
Raypak 120 - page 56
56 13 - LPG INSTRUCTIONS LPG INSTRUCTIONS PROP ANE GAS: CAUTION: The gas supply shall be shut off prior to disconnecting the electrical power, before proceding with the conversion. Installation Codes Installations must follow these codes: • Local, state, provincial, and national codes, laws, regulations and ordinances • National Fuel Gas Code, ...
-
Raypak 120 - page 57
57 TECHNICAL DATA - LPG Gas pre ssure XPak 85 XPak 120 Input - (0 - 2000 ft / 0 - 610 m) Btu/hr 25,600 - 87,000 27,300 - 119,500 k W 7.5 - 25.5 8.0 - 35.0 Input - (2000 - 4500 ft / 610 - 1375 m) Btu/hr 25,600 - 82,900 27,300 - 114,300 k W 7.5 - 24.3 8.0 - 33.5 Gas supply pressure LPG in w . c . 11 1 1 kP a 2.75 2.75 Min. gas supply pressure LPG in ...
-
Raypak 120 - page 58
58 IMPORTANT A GAS TIGHTNESS CHECK MUST BE CARRIED OUT IF ANY GAS CARRYING COMPONENTS HAVE BEEN REMOVED, REPLACED, OR DISTURBED. XPAK LPG LABEL 1. Fill in the enclosed LPG label with all the information required and affix the label as close as possible to existing rating plate 2. Affix the enclosed RED color label over the existing YELLOW color lab ...
-
Raypak 120 - page 59
59 14 - EXPLODED DIAGRAMS Drawing 1 5 7 9 3 12a 4 6 8 12a 1 10 2 11 ...
-
Raypak 120 - page 60
60 Drawing 2 17 18 56a 56a 14 15 56b 13 16 12b 19 ...
-
Raypak 120 - page 61
61 Drawing 3 12d 12d 23 24c 24e 24d 24b 22 28 26 21d 56a 21c 56a 56c 21a 28 21b 24a 20 27 12c 25 23 24b 24c 24e 24d 24a 22 21d 26 28 56a 21c 12d XP AK 120 XP AK 85 25 ...
-
Raypak 120 - page 62
62 Drawing 5 Drawing 4 30 30 29 39 38 37 36 43 56a 47 42 31 33 34 40 35 41 32 44 57b 45 46 52 Drawing 5 57 53 Drawing 5 57b 58 49 55 51 53 52 50 48 54 ...
-
Raypak 120 - page 63
63 CALL OU T DESCRIPTION XPak85 XPak120 Electric/Case Components See Drawing #1 1 Jack et Front 012831F 012832F 2 Boiler Mounting Bracket 013004F 013004F 3 Control Panel 012829F 012829F 4 Control Panel Cover 012827F 012827F 5 Control Panel Door 012833F 012833F 6 PC Board 012828F 012828F 7 Control Knob 012830F 012830F 8 Control Panel Hinge 012834F 0 ...
-
Raypak 120 - page 64
64 Important Instructions for the Commonwealth of Massachusetts The Commonwealth of Massachusetts requires compliance with regulation 248 CMR 4.00 and 5.00 for installation of through – the – wall vented gas appliances as follows: (a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure u ...
-
Raypak 120 - page 65
65 LIMITED W ARRANTY MODULA TING - CONDENSING BOILER XP AK TM HEA TING BOILERS MODELS 85 & 120 SCOPE OF W ARRANTY : Raypak, Inc. (“Raypak”) warr ants to the first retail purchaser of the XP AKHeating Boiler that was deliv ered with this limited w arranty cer tificate (the “Boiler”) that the Boiler will be free from defects in materials ...
-
Raypak 120 - page 66
66 3. to damage, malfunctions or failures resulting from misuse, neglect, alteration, accident, fire, flood and the like; 4. to damage, malfunctions or failures resulting from sediment or lime buildup, freezing, or other conditions causing inadequate water circulation; 5. to damage, malfunctions or failures resulting from high velocity flow exceedi ...
-
Raypak 120 - page 67
67 ST ART -UP CHECKLIST FOR F AN-ASSISTED RA YP AK PR ODUCTS This start-up checklist is to be completely filled out by the service technician starting up the Raypak Boiler for the first time. All information may be used for warranty purposes and to ensure that the installation is correct. Additionally this form will be used to record all equipment ...
-
Raypak 120 - page 68
Y our XP ak ser ial number f or future ref erence www .raypak.com Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 Fax (805) 278-5468 ...
Do you have a question concerning Raypak 120?
Use the form below
If you did not solve your problem by using a manual Raypak 120, ask a question using the form below. If a user had a similar problem with Raypak 120 it is likely that he will want to share the way to solve it.