English dropdown-ico

Manual Husqvarna 346XP 351

36 pages 1.68 mb
Download

Go to site of 36

Summary
  • Husqvarna 346XP 351 - page 1

    Oper a tor´s manual Please read these instructions car efully and make sur e you understand them bef ore using the machine. English 346XP 351 ...

  • Husqvarna 346XP 351 - page 2

    2 – English Symbols KEY T O SYMBOLS CAUTION! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. Always wear approved protective gloves. Regular cleaning is require ...

  • Husqvarna 346XP 351 - page 3

    English – 3 CONTENTS Contents Key to symbols ............................................................... 2 Safety instructions Personal protective equipment ............................................ 4 Chain saw safety equipment ................................................ 4 Inspecting, maintaining and servicing chain saw safety equipme ...

  • Husqvarna 346XP 351 - page 4

    4 – English SAFETY INSTRUCTIONS • PROTECTIVE HELMET • HEARING PROTECTION • PROTECTIVE GLASSES OR VISOR • PROTECTIVE GLOVES WITH SAW PROTECTION • PROTECTIVE TROUSERS WITH SAW PROTECTION • BOOTS WITH SAW PROTECTION, STEEL TOE-CAP AND NON-SLIP SOLE Generally clothes should be close-fitting without restricting your freedom of movement. ? ...

  • Husqvarna 346XP 351 - page 5

    English – 5 1 Chain brake and front hand guard YOUR chain saw is equipped with a chain brake that is desig- ned to stop the chain immediately if you get a kickback. The chain brake reduces the risk of accidents, but only You can prevent them. Take care when using your saw and make sure the kickback zone of the bar never touches any object. 1 The ...

  • Husqvarna 346XP 351 - page 6

    6 – English 6 The way the chain brake is triggered, either manually or automatically, depends on the force of the kickback and the position of the chain saw in relation to the object that the kickback zone of the bar strikes. If you get a violent kickback while the kickback zone of the bar is farthest away from you the chain brake will be activat ...

  • Husqvarna 346XP 351 - page 7

    English – 7 5 Vibration damping system Your chain saw is equipped with a vibration damping system that is designed to minimise vibrations and make operation easier. When you use a chain saw vibrations are generated by the uneven contact between the chain and the wood you are cutting. Cutting hardwoods (most broadleaf trees) creates more vibration ...

  • Husqvarna 346XP 351 - page 8

    8 – English SAFETY INSTRUCTIONS 3 Checking the inertia brake release Hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar falls onto the stump. When the bar hits the stump the brake should be applied. 4 Checking the brake trigger Place the chain saw on a firm surface and start it. Make sure the chain do ...

  • Husqvarna 346XP 351 - page 9

    English – 9 SAFETY INSTRUCTIONS 4 Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. 5 Vibration damping system Regularly check the vibration damping units for cracks or deformation Make sure the vibration damping units are securely attached to the engine unit and handles. 6 Stop ...

  • Husqvarna 346XP 351 - page 10

    10 – English 7 Muffler Never use a chain saw that has a faulty muffler. Regularly check that the muffler is securely attached to the chain saw. If the muffler on your saw is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage. Never use a muffler if the ...

  • Husqvarna 346XP 351 - page 11

    English – 11 SAFETY INSTRUCTIONS C Some terms that describe the bar and chain When the cutting equipment supplied with your saw becomes worn or damaged you will need to replace it. Use only the type of bar and chain recommended by us. See the ” Technical data ” section to find out which equipment is recommended for your saw. Bar • LENGTH (i ...

  • Husqvarna 346XP 351 - page 12

    12 – English SAFETY INSTRUCTIONS 2 Sharpening your chain and adjusting raker clearance The risk of kickback is increased with a badly sharpened chain! A General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the cuttings will be ver ...

  • Husqvarna 346XP 351 - page 13

    English – 13 C General advice on setting raker clearance • When you sharpen the cutting teeth you reduce the RAKER CLEARANCE (cutting depth). To maintain cutting performance you must file back the raker teeth to the recommended height. See the ” Technical data ” section to find the raker clearance for your saw chain. • On a low-kickback c ...

  • Husqvarna 346XP 351 - page 14

    14 – English 1 Undo the bar nuts that hold the clutch cover and chain brake, using the combination spanner. Then tighten the nuts by hand as tight as you can. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it not hang slack on the underside of the ba ...

  • Husqvarna 346XP 351 - page 15

    English – 15 C Checking chain lubrication • Check the chain lubrication each time you refuel. Aim the tip of the saw at a light coloured surface about 20 cm away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface. If the chain lubrication is not working: 1 Check that the oil channel in the bar is ...

  • Husqvarna 346XP 351 - page 16

    16 – English H Bar Check regularly: • Whether there are burrs on the edges of the bar. Remove these with a file if necessary. • Whether the groove in the bar has become badly worn. Replace the bar if necessary. • Whether the tip of the bar is uneven or badly worn. If a hollow forms on one side of the bar tip this is due to a slack chain. ? ...

  • Husqvarna 346XP 351 - page 17

    English – 17 7 Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is known as cutting on the push stroke. The chain tries to push the saw back towards the user. Unless the user resists this pushing force there is a risk that the saw will move so far backwards that only the kickback ...

  • Husqvarna 346XP 351 - page 18

    18 – English SAFETY INSTRUCTIONS GENERAL SAFETY PRECAUTIONS 1 Chain saws are designed solely for cutting wood. The only cutting equipment that can be used with this chain saw are the combinations of bars and chains recommended in the ”Technical data” section. 2 Never use a chain saw if you are tired, if you have drunk alcohol, or if you are t ...

  • Husqvarna 346XP 351 - page 19

    English – 19 SAFETY INSTRUCTIONS Min. 3 m (10 ft) • Never try to refuel the saw while it is running. • Make sure there is plenty of ventilation when refuelling or mixing fuel (2-stroke mixture). • Move the saw at least 3 m from the refuelling point before starting it. • Never start the chainsaw: a) If you have spilt fuel or chain oil on t ...

  • Husqvarna 346XP 351 - page 20

    20 – English SAFETY INSTRUCTIONS 6 Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the saw with the bar and chain pointing backwards. Fit a guard to the bar before carrying the saw any distance. 7 Never put a chain saw down while the engine is running unless you have it in clear view and the chai ...

  • Husqvarna 346XP 351 - page 21

    English – 21 SAFETY INSTRUCTIONS 2 The log is supported at one end. There is a high risk that it will split. A Start by cutting from below (about 1/3 of the way through). B Finish by cutting from above so that the two cuts meet. 3 The log is supported at both ends. There is a high risk that the chain will jam. A Start by cutting from above (about ...

  • Husqvarna 346XP 351 - page 22

    22 – English SAFETY INSTRUCTIONS C Clearing the trunk and preparing your retreat Remove any branches that are in the way. To do this it is best to work from the top down and keep the trunk between you and the chain saw. Never limb above shoulder height. Remove any undergrowth from the base of the tree and check the area for obstacles (stones, bra ...

  • Husqvarna 346XP 351 - page 23

    English – 23 We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the FELLING CUT and DIRECTIONAL CUT with single cutting stokes. (See ” Technical data ” to find out which lengths of bar are recommended for your saw). There are methods for felling trees with a diameter larger than the bar length. ...

  • Husqvarna 346XP 351 - page 24

    24 – English WHA T IS WHA T? 1. Cylinder cover. 2. Front handle. 3. Front hand guard. 4. Starter cover. 5. Chain oil tank. 6. Starter handle. 7. Adjuster screw, carburettor. 8. Choke control/Start throttle lock. 9. Rear handle. 10. Stop switch. Ignition on/off switch. 11. Fuel tank. 12. Muffler. 13. Bar tip sprocket. 14. Saw chain. 15. Saw bar. W ...

  • Husqvarna 346XP 351 - page 25

    English – 25 ASSEMBL Y Fitting a spike bumper To fit a spike bumper – contact your service agent. Hold up the tip of the bar and tighten the chain. The chain is correctly tensioned when there is no slack on the underside of the bar, but it can still be turned easily by hand. Hold up the bar tip and tighten the bar nuts with the combination wren ...

  • Husqvarna 346XP 351 - page 26

    26 – English Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mixture thoroughly before filling the saw ’ s fuel tank. ...

  • Husqvarna 346XP 351 - page 27

    English – 27 FUEL HANDLING Fuelling Taking the following precautions, will lessen the risk of fire. • Do not smoke or place warm objects in the vicinity of the fuel. • Always shut off the engine before refuelling. • Slowly open the fuel cap, when filling fuel, so that possible overpressure is slowly released. • Tighten the fuel cap carefu ...

  • Husqvarna 346XP 351 - page 28

    28 – English Cold engine STARTING: The chain brake must be engaged when the chain saw is started. Activate the brake by moving the front hand guard forwards. IGNITION; CHOKE: Set the choke control in choke position. The stop contact will automatically be set to start position. FAST IDLE: Combined choke/fast idle is received when the choke is move ...

  • Husqvarna 346XP 351 - page 29

    English – 29 Carburettor Functioning, Basic setting, Final setting WARNING! Do not start the saw without the bar, chain and clutch cover (chain brake) assembled. If you do, the clutch might come loose and cause severe injuries. Operation • The carburettor governs the engine speed via the throttle. Air/fuel are mixed in the carburettor. The air/ ...

  • Husqvarna 346XP 351 - page 30

    30 – English Starter device WARNING! • When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop out and cause injuries. • Always be careful, when changing the recoil spring or the starter cord. Always wear safety goggles for eye protection. MAINTENANCE Changing a broken or wo ...

  • Husqvarna 346XP 351 - page 31

    English – 31 Muffler The muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Some mufflers are equipped with a special screen. MAINTENANCE If your saw has this type of ...

  • Husqvarna 346XP 351 - page 32

    32 – English MAINTENANCE Cooling system To obtain the lowest possible running temperature the saw is equipped with a cooling system. The cooling system consists of: 1. Air intake on the starter unit. 2. Air guide plate. 3. Fan blades on the flywheel. 4. Cooling fins on the cylinder. 5. Cylinder cowling (supplies cold air over the cylinder). Clean ...

  • Husqvarna 346XP 351 - page 33

    English – 33 Below you will find some general maintenance instructions. If you have more questions, contact your servicing dealer. W eekly maintenance 1. Check that the AV elements are not soft or torn. 2. Lubricate the clutch drum bearing. 3. File off burrs, if any, on the sides of the bar. 4. Clean the spark plug and check the gap. The correct ...

  • Husqvarna 346XP 351 - page 34

    34 – English TECHNICAL DA T A 346XP 2,7/45,0 1,65/42,0 1,28/32,5 2 700 14 200 2,5/ 9 600 FHP CD NGK BPMR 7A Champion RCJ 7Y 0,020/0,5 Walbro HDA 159A 1,06/0,5 6-10 0,59/0,28 Automatic 346XP: 10,6/4,8 346XPG: 10,8/4,9 346XP E-tech: 10,8/4,9 346XPG E-tech: 11,0/5,0 346XP: 113 346XPG: 113 346XP E-tech: 110 346XPG E-tech: 110 346XP: 114 346XPG: 114 3 ...

  • Husqvarna 346XP 351 - page 35

    English – 35 TECHNICAL DA T A Bar and chain combinations The following combinations are CE approved. Bar Chain Length, Pitch, Max. inches inches tip radius 13 0,325 10T Husqvarna H30 15 0,325 10T Husqvarna H30 16 0,325 10T Husqvarna H30 18 0,325 10T Husqvarna H30 13 0,325 10T Husqvarna H25 15 0,325 10T Husqvarna H25 16 0,325 10T Husqvarna H25 18 ...

  • Husqvarna 346XP 351 - page 36

    2001W49 ´+H$J¶6q¨ 114 00 44-26 ...

Manufacturer Husqvarna Category Chainsaw

Documents that we receive from a manufacturer of a Husqvarna 346XP 351 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 346XP 351 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 346XP 351
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 346XP 351.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 346XP 351, service manual, brief instructions and user manuals Husqvarna 346XP 351. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 346XP 351.

Similar manuals

A complete manual for the device Husqvarna 346XP 351, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 346XP 351 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 346XP 351.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 346XP 351 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 346XP 351, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 346XP 351, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 346XP 351 - which should help us in our first steps of using Husqvarna 346XP 351
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 346XP 351
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 346XP 351 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 346XP 351?

Use the form below

If you did not solve your problem by using a manual Husqvarna 346XP 351, ask a question using the form below. If a user had a similar problem with Husqvarna 346XP 351 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)