English dropdown-ico

Manual Hawking Technology 10M

25 pages 1.48 mb
Download

Go to site of 25

Summary
  • Hawking Technology 10M - page 1

    1 ...

  • Hawking Technology 10M - page 2

    FCC Warning This equipment has been tested and found to comply with the lim its for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable prot ection against harmful interference in a residen tial installation. This equipment generates, uses and can radiate radio frequency energy and, i ...

  • Hawking Technology 10M - page 3

    Unpacking the Switch 4 Introduction 1.1 General Description 5 1.2 Gigabit Ethernet Technology 5 1.3 Features 6 1.4 Front Panel 6 1.5 Rear Panel 7 Installation 2.1 Desktop Installation 8 2.2 Rack-Mount Installation 8 2.3 Installing Network Cables 9 2.4 Network Application 9 Description of Functions 3.1 PHY Monitoring and Port Mode Setup 10 3.2 Flow ...

  • Hawking Technology 10M - page 4

    The complete HGS16S package consists of: • One HGS16S 16-Port 10/100/1000M Web-Smart Switch • Rack mount kit: 2 mounting brackets and screws • Four rubber feet with adhesive backing • One AC power cord • One RS-232 cable • One CD • One Quick Installation Guide Check to make sure that the unit was not damaged during shipping and that n ...

  • Hawking Technology 10M - page 5

    1.1 General Description The device is a 16-port 10/100/1000Mbps Ethernet Web-Smart Switch. Compared with traditional 10/100Mbps Ethernet, the switch de livers a dedicated Gigabit connection to every attached client with no congestion issues. The gigabit ports also provi de a larger pipe to the server or backbone connectivity for boosting total syst ...

  • Hawking Technology 10M - page 6

    1.3 Key Features • 16 fixed 10/100/1000Mbps Gigabit Ethernet ports • Provides Auto-discovery Function for easy network management • Provides 4K MAC address entries • 16 groups VLAN table • Supports up to 8 groups (of up to 8 ports each) port aggregation • Supports QoS for enhanced network management • Supports full duplex flow control ...

  • Hawking Technology 10M - page 7

    Wiring for 10/100/1000Mbps (Copper) Below is the summary of the cabling required: Media Speed Wiring 10Mbps Category 3,4,5 UTP/STP 100Mbps Category 5 UTP/STP 10/100/1000Mbps copper 1000Mbps Category 5,5e UTP/STP LED Definition The rich diagnostic LEDs on the front panel help display th e operating status of individual ports as well as the entire sy ...

  • Hawking Technology 10M - page 8

    This switch can be placed directly on your desktop, on the floor, or mounted in a rack. Users can immediately use most of the features simply by attaching the cables and turning the power on. 2.1 Desktop Installation For desktop installation, the switch needs to be put on a clean, flat desk or table close to a power outlet. After you have plugged i ...

  • Hawking Technology 10M - page 9

    2.3 Installing Network Cables Station Connections Refer to the wiring statement of the previous section; connect each station/device to the switch with the correct cables. Switch-to-Switch Connections In making a switch-to-switch connection, using every po rt to connect another switch or backbone is stro ngly recommended. The gigabit ports provide ...

  • Hawking Technology 10M - page 10

    3.1 PHY Monitoring and Port Mode Setup One of the software’s major tasks is to continuously monito r the PHYs in order to set up t he switch ports according to whether the link is up or down, and in the latter case, what the current speed, duplex mode and pause capabilities are. The PHYs are polled every 100 ms. 3.2 Flow Control In the 16-port sw ...

  • Hawking Technology 10M - page 11

    This section instructs you on how to enter and set up the c onfigurations, whi ch can be accessed by RS-232 serial port (out-of-band) on the rear panel or by Telnet sessi on / Internet Browser over the network (in-band). Factory Default value: IP: 192.168.1.1 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.254 4.1 Access the Switch Console Po ...

  • Hawking Technology 10M - page 12

    In-Band Connections (Web Browser / Telnet) To manage the switch through in-band access, you should co nfigure the managem ent station with an IP address and subnet mask compatible with your switch. 1. Run your Web Browser and enter the IP address “192.168.1.1” as the URL in the “address” field. 2. Key in the User na me and password to pass ...

  • Hawking Technology 10M - page 13

    4.2 Homepage On the Home page, you can select what you would like to config ure by clicking the menu tabs located at the top of the homepage. They include: • System • Ports • VLANS • Aggregation • QoS • Mirror • Statistics • Discovery Configuration Tabs Detailed Port Statistics 13 ...

  • Hawking Technology 10M - page 14

    To restore the default values of switch, click the “ Default ” button at the top of the homepage. If you want to reboot the switch, click the “ Reboot ” Button. To check the connection status of each port, from 1 to 16, take a look at the port monitor. When the port shows green , it is connected. Otherwise it will remain dark . To know the ...

  • Hawking Technology 10M - page 15

    4.2.1 System To set up the system configurations such as login values, time-out values, and for enabling the VLAN Management: Items Functions Mac Address The Mac Address of the switch S/W Version To look up the Software Version, see here. H/W Version The Hardware version Inactivity Timeout (Secs) Set the console inactivity timeout in seconds. The v ...

  • Hawking Technology 10M - page 16

    Note: After you change the IP address, the switch will reboot itself. You may click the new address to link the New IP Address with your browser. 4.2.2 Ports On this page, you can view the port status, set up the speed “Mode” and enable the “FDX Flow Control”. 16 ...

  • Hawking Technology 10M - page 17

    Items Functions Link Shows the status of each port. When it is red, it means the connection is down. Otherwise, it is green. Mode Choose the Speed mode of port: 10/100/1000, Half/Full. To disable the port, choose “Disable”. If you set to auto-speed, it will be auto- negotiation. FDX Flow Contro l To Enable the FDX Flow control, click the check ...

  • Hawking Technology 10M - page 18

    PVID When the VLAN-enabled switch receives a ta gged packet, the packet will be sent to the port’s default VLAN according to the PVID (port VLAN ID) of the receiving port. Items Functions Port Port Number 1~16 PVID Port VLAN ID Aware To enable the PVID checking and inserting of one port, select “AWARE” Only Tagged Block the untagged frame. Ap ...

  • Hawking Technology 10M - page 19

    19 ...

  • Hawking Technology 10M - page 20

    4.2.4 Aggregation/Trunking Configuration To set up the Port trunk groups, put the port numbers into the same Aggregation group line . There are eight groups that can be made. Do not forget to click the “Apply” to save th e settings. The m aximum number of ports for one group is 8. There are three aggregation modes for you to setup, SMAC (Source ...

  • Hawking Technology 10M - page 21

    4.2.5 QoS There is one mode of Quality of Service to choose: custom TOS. 4.2.5.1 Custom ToS To improve the network performance by applying the TOS, set up the priority of eight groups of precedence bits on this page. There are two types to choose, high or Low. Items Functions Port To select the switch port, from 1 to 16 Priority Select the priority ...

  • Hawking Technology 10M - page 22

    4.2.6 Mirror Port mirror is used to mirror traffic from a source port to a target port for analysis. Only 2 ports can be monitored (mirrored) simultaneously to 1 Monito r port (target port). (Note that the targe t port must be in the same VLAN as the source port) Items Functions Monitor Port Select the switch port, from 1 to 16 to be the target por ...

  • Hawking Technology 10M - page 23

    4.2.7 Statistics To check the status of port traffic, click the “Statistic” tab. You can click the “ Clear ” button to erase all records or click “ Refresh ” to show the most current status. 4.2.8 Discovery When you install several our 16-port and 24- port gigabit web-sm art switches, the discovery management tool helps you to search an ...

  • Hawking Technology 10M - page 24

    4.2.9 Default To restore to default values, 1. Click the default button on the homepage. 2. Click “Yes” to restore default values. Do not power off the switch while it is working. 4.2.10 Reboot To reboot the switch, 1. Click the “Reboot” button on the homepage 2. Click “Yes” to reboot. Do not power off the switch while it is working. 24 ...

  • Hawking Technology 10M - page 25

    Standard IEEE802.3 10BASE-T IEEE802.3u 100BASE-TX IEEE802.3x full-duplex operation and flow control IEEE802.3ab 1000BASE-T IEEE802.1Q VLAN interoperability IEEE802.1p Traffic prioritization Interface 16 * 10/100/1000Mbps auto MDI/MDI-X RJ-45 switching ports 1 * RS-232 Console port Cable Connections RJ-45 (10BASE-T): Category 3,4,5 UTP/STP RJ-45 (10 ...

Manufacturer Hawking Technology Category Switch

Documents that we receive from a manufacturer of a Hawking Technology 10M can be divided into several groups. They are, among others:
- Hawking Technology technical drawings
- 10M manuals
- Hawking Technology product data sheets
- information booklets
- or energy labels Hawking Technology 10M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hawking Technology 10M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hawking Technology 10M, service manual, brief instructions and user manuals Hawking Technology 10M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hawking Technology 10M.

Similar manuals

A complete manual for the device Hawking Technology 10M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hawking Technology 10M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hawking Technology 10M.

A complete Hawking Technology manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hawking Technology 10M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hawking Technology 10M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hawking Technology 10M, that we can find in the current document
3. Tips how to use the basic functions of the device Hawking Technology 10M - which should help us in our first steps of using Hawking Technology 10M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hawking Technology 10M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hawking Technology 10M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hawking Technology 10M?

Use the form below

If you did not solve your problem by using a manual Hawking Technology 10M, ask a question using the form below. If a user had a similar problem with Hawking Technology 10M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)