English dropdown-ico

Manual IEI Technology SEG-1

34 pages 1.63 mb
Download

Go to site of 34

Summary
  • IEI Technology SEG-1 - page 1

    Secure Ethernet Gateway SEG-1 and SEG-M for IEI Access Systems Installation Manual Section 1: Introduction SECURITY WARNING: New SEG's shipped after April 2008 will have Telnet setup option enabled by default. Enabling Telnet on the SEG allows you (the customer) to be able to configure the settings of the SEG via LAN without requiring the seri ...

  • IEI Technology SEG-1 - page 2

    Table of Contents Section 1: Introduction ........... .......... ........... .......... .......... ........... .......... ........... .......... ........... ........... .... .... .1 Section 2: Product Overview ............ .......... .......... ........... .......... ........... .......... ........... ........... .... .... .... .... ... 3 2.1 Produ ...

  • IEI Technology SEG-1 - page 3

    Section 2: Product Overview 2.1 Product Specifications The chart below contains the environmental and electrical specifications. Electrical Voltage 12VDC (9V Min; 20V Max) Current 150mA @ 9V; 100mA @ 20V Environmental Temperature 0° to 70 ° C (32° to 158° F) Humidity 0-95% RH Non-condensing Environment Indoor Only 2.2 LED Status The following d ...

  • IEI Technology SEG-1 - page 4

    Section 3: Hardware Installation The following section contains information about installing the SEG-1 and SEG-M hardware. 3.1 SEG-1 Diagrams Page 4 of 34 Document Nu mber: 6066 005, Rev 3. 2 ...

  • IEI Technology SEG-1 - page 5

    3.2 Connection the SEG-1 to a HubMax or Hub MiniM ax (RS-232) Two different methods can be used to connect Port A of the HubMax or HubMiniMax to the SEG-1: 1. Connect to the RS232 modular jack (front of SEG-1) 2. Connect to the RS232 terminals (rear of SEG-1) NOTE: If connection to SEG-1 is NOT located at the HubMax or HubMiniMax then the connectio ...

  • IEI Technology SEG-1 - page 6

    3.3 Connecting the SEG-1 to HC500P (RS-232) Two different methods to can be used to connect Port A of the HC500P to the SEG-1 1. Connect to the RS232 modular jack (front of SEG-1) 2. Connect to the RS232 terminals (rear of SEG-1) NOTE: If connection to SEG-1 is NOT located at the HC500P then the connection must be made via stranded/shielded cable. ...

  • IEI Technology SEG-1 - page 7

    3.4 Connecting Multiple HubMax/Hub MiniMax Netw orks Document N umber: 60660 05, Rev 3.2 Page 7 of 34 ...

  • IEI Technology SEG-1 - page 8

    3.5 Connecting the SEG-1 to a prox.pad p lus (RS-485) Two different methods can be used to connect P5 Connector of the prox.pad plus to the SEG-1: 1. Connect to the RS485 modular jack (front of SEG-1) 2. Connect to the RS485 terminals (rear of SEG-1) NOTE: If connection to SEG-1 is NOT located at the prox.pad plus then the connection must be made v ...

  • IEI Technology SEG-1 - page 9

    3.6 Connecting Multiple prox.pad plus Netw orks Document N umber: 60660 05, Rev 3.2 Page 9 of 34 ...

  • IEI Technology SEG-1 - page 10

    3.7 Connecting the SEG-1 to a Max 3 System ( RS-485) You can also use the SEG-1 to connect your Max 3 or MiniMax 3 system to your LAN/WAN. Follow the instructions below and refer to the diagram. Run y our RS-485 cable between terminal strip TS1 on the SEG-1 to TS 3 on the backplane as shown in the diagram. You must also connect each module to the b ...

  • IEI Technology SEG-1 - page 11

    3.8 Connecting the SEG-1 to a MiniMax 3 System (RS-485) You can also use the SEG-1 to connect your MiniMax 3 s y stem to your LAN/WAN. Follow the instructions below and refer to the diagram. Run y our RS-485 cable between terminal strip TS1 on the SEG-1 to TS 3 on the backplane as shown in the diagram. You must also connect the module to the backpl ...

  • IEI Technology SEG-1 - page 12

    3.9 SEG-M Installation (Plug On Module) The SEG-M plug on module was created to allow HubMax and Mi niMax panels an easier way to use the SEG-M functionality. When used with HubMax or Hub MiniMax panels, no power or communication wiring is required between the SEG-M and the backplane. All connections are made through the connector used to connect t ...

  • IEI Technology SEG-1 - page 13

    3.9.2 SEG-M Connectors The chart below describes the connectors on the S EG-M. Connector Description Pin Configuration J1 RS-485 Data Connector Pin Label Description 1 A RS-485 Data A (+) 2 B RS-485 Data B (-) 3 GND RS-485 Data GND 4 A RS-485 Data A (+) 5 B RS-485 Data B (-) 6 GND RS-485 Data GND S1 Power/RS-232 Data Connector Power/RS-232 Connecto ...

  • IEI Technology SEG-1 - page 14

    3.9.4 Connecting the SEG-M to a HubMax S ystem (RS-232) Connect the SEG-M to the eight-position pin rail S1 above the first module on the backplane. Make sure the components on the SEG- M are facing away from the module. Use the t wo card guides to secure the SEG-M in place by snapping them into the holes on either side and sliding the SEG-M into t ...

  • IEI Technology SEG-1 - page 15

    3.9.6 Connecting the SEG-M to a Max 3 System (RS-485) You can connect your Max 3 to your LAN/WAN by using the SEG-M, Secured Ethernet Gateway. Follow the instructions below and refer to the diagram. The connection from the SEG-M to the Max 3 requires you to plug the modul e onto the backplane connector S1 to power the unit. You must also use the si ...

  • IEI Technology SEG-1 - page 16

    3.9.7 Connecting the SEG-M to a MiniMax 3 System (R S-485) You can connect your MiniMax 3 to your LAN/WAN by using the SEG-M, S ecured Ethernet Gateway . Follow the instructions below and refer to the diagram. The connection from the SEG-M to the MiniMax 3 requires you to pl ug the module onto the backplane connector J2 to power the unit. You must ...

  • IEI Technology SEG-1 - page 17

    Section 4: SEG Configuration The SEG is a device created for the purpose of allowing data to be exported from your PC over a LAN/WAN to either Secured S eries Controllers or the prox.pad Plus. A minimal amount of setup must be performed on the SEG in order for it to be properly addressed on the LAN. There are 3 methods that can be used to configure ...

  • IEI Technology SEG-1 - page 18

    Page 18 of 34 Document Number : 60660 05, Rev 3.2 Figure 1: No SEG parameters defined Figure 2: SEG firmware requirements ...

  • IEI Technology SEG-1 - page 19

    Document N umber: 606 6005, R ev 3.2 Pa ge 19 of 34 Figure 3: Found SEG's are displayed in grid Figure 4: Select a SEG ...

  • IEI Technology SEG-1 - page 20

    4.2 Dynamic IP A ddress, non-expiring lease No setup of the SEG via the serial port is required. Just supply the SEG's MAC address (the 12 digit number located on the label on the SEG; for example 00-20-4A-52-F2-84) to the IT department and ask them to assign it an IP Address with a non-expiring lease. Once you have the IP address that the IT ...

  • IEI Technology SEG-1 - page 21

    4.3 Static IP A ddress The static IP address can be set through the serial port of the S EG using the PC's serial communications port (or through the USB port using a USB to RS232 adapter). This method allows you to configure the IP address of the SEG without any network devices such as a router or a network switch interfering. Refer to the se ...

  • IEI Technology SEG-1 - page 22

    8. Disconnect power to the SEG (if it was powered up). 9. Press and hold down the x key (lowercase) on the PC keyboard while the HyperTerminal program is running. 10. Power up the SEG. 11. In a few seconds you should get a response from the SEG asking y ou to press enter to go into Setup Mode. 12. Release the x key. 13. After pressing ENTER to go i ...

  • IEI Technology SEG-1 - page 23

    4. Type cmd and then press OK. A DOS prompt will appear. 5. Type the following and press enter: telnet <IP address of SEG> 9999 (for example: telnet 192.168.1.1 9999 ) 6. You should get a response from the SEG asking you to press enter to go into S etup Mode. 7. Press enter to enter the setup menu of the SEG. 8. Now go to section “4.3.3 SEG ...

  • IEI Technology SEG-1 - page 24

    4.3.3 SEG Setup Menu 1. To change the IP address you should select option 0 server Configu ration . A 3 digit number will be displayed in brackets. This is the first 'octet' of the current IP address of this SEG device. You will either enter a new 3 digit number and then press enter to accept it, or you can accept this num ber by pressing ...

  • IEI Technology SEG-1 - page 25

    Here is a brief description of each m enu and sub option, and what the default values should be. The SEG device is factory set to have the highest security possible. Changing any options, especially i n the 'Security' menu could result in not having a completely secure environment. 0 – Sever Configuration IP Address (XXX).(XXX).(XXX).(X ...

  • IEI Technology SEG-1 - page 26

    6 – Security Here you can change the Encryption key manually to match the encry ption ke y Hub Manager Professional is using. This is normally not necessary because Hub Manager Professional normall y performs this function. After going through this menu item completely, the encryption settings will automaticall y be saved and the session will be ...

  • IEI Technology SEG-1 - page 27

    4.3.4 Configuring the IP Address in H ub Manager Professional Now it is time to open Hub Manager Professional, create a new site, and configure this site to communicate to the SEG wit h the I P address you have received from the IT administrator. Thi s example shows how to set up a SEG connected Hub controller network, but the SEG can also be used ...

  • IEI Technology SEG-1 - page 28

    4.4.5 Generate Random Security Key This button will generate a new 128 bit security key and wi ll then display the hexadecimal representation in the 'Current Security Key' field (see below) 4.4.6 Generate Default Security Key After selecting this option, you will receive a warning m essage explaining that setting the security key back to ...

  • IEI Technology SEG-1 - page 29

    4.5.2 Reset the Security Key in the SEG to a ll 0's NOTE: This requires SEG firmware v1.30 or higher. This feature is provided to allow you to reset the S ecurity Key in the SEG back to all 0's, which is the default out-of-box state. Resetting the Security Key in the SEG would be required if y ou are replacing a SEG with a previously used ...

  • IEI Technology SEG-1 - page 30

    Section 5: Trouble Shooting Page 30 of 34 Document Number : 60660 05, Rev 3.2 ...

  • IEI Technology SEG-1 - page 31

    Document N umber: 606 6005, R ev 3.2 Pa ge 31 of 34 ...

  • IEI Technology SEG-1 - page 32

    Page 32 of 34 Document Number : 60660 05, Rev 3.2 ...

  • IEI Technology SEG-1 - page 33

    Section 6: FCC Compliance Statement This equipment has been tested and found to comply with the limi ts for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated i n a commercial environment. This equipment generates, use ...

  • IEI Technology SEG-1 - page 34

    Page 34 of 34 Document Number : 60660 05, Rev 3.2 International Electronics, Inc. 427 Turnpike St. Canton, MA 02021 U.S.A. Phone: 800-343-9502, 781-821-5566 Fax: 781-821-4443 Website: www .ieib.com ...

Manufacturer IEI Technology Category Switch

Documents that we receive from a manufacturer of a IEI Technology SEG-1 can be divided into several groups. They are, among others:
- IEI Technology technical drawings
- SEG-1 manuals
- IEI Technology product data sheets
- information booklets
- or energy labels IEI Technology SEG-1
All of them are important, but the most important information from the point of view of use of the device are in the user manual IEI Technology SEG-1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals IEI Technology SEG-1, service manual, brief instructions and user manuals IEI Technology SEG-1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product IEI Technology SEG-1.

Similar manuals

A complete manual for the device IEI Technology SEG-1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use IEI Technology SEG-1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of IEI Technology SEG-1.

A complete IEI Technology manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual IEI Technology SEG-1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the IEI Technology SEG-1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the IEI Technology SEG-1, that we can find in the current document
3. Tips how to use the basic functions of the device IEI Technology SEG-1 - which should help us in our first steps of using IEI Technology SEG-1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with IEI Technology SEG-1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of IEI Technology SEG-1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning IEI Technology SEG-1?

Use the form below

If you did not solve your problem by using a manual IEI Technology SEG-1, ask a question using the form below. If a user had a similar problem with IEI Technology SEG-1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)