English dropdown-ico

Manual Extron electronic PVS 300

46 pages 10.37 mb
Download

Go to site of 46

Summary
  • Extron electronic PVS 300 - page 1

    PoleV ault Systems Installation Guide for the PVS 200, 300, and 400 68-1390-01 Rev . C 10 08 ...

  • Extron electronic PVS 300 - page 2

    This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution Read Instructions • ...

  • Extron electronic PVS 300 - page 3

    1-1 PoleV ault Systems Installation • Introduction Intr oduction Overview This manual covers the installation of the Extron PoleV ault ™ System in a drop ceiling r oom with a wood or concrete structural ceiling. If the location has a concrete or beam style ceiling, alternative ceiling mounts can be obtained separately from Extr on ( see 2c, &qu ...

  • Extron electronic PVS 300 - page 4

    PoleV ault Systems Installation • Introduction 1-2 Intr oduction, cont'd L R AU X/MIX IN DO NO T GROU ND OR SHORT SPEAKER OUT PUTS ! 1B 1A I N P U T S O U T P U T S 2B 2A 3B 3A RS-232 MLC/IR DC VO L 4/8 Ohms AMPLIFIED OUTPUTS VO L/MUTE Tx A B C Rx IR 12V 10V PO WE R 12V 3A MA X US LISTED 17T T AU DIO/VIDE O AP PA RA TU S ® RG B VIDE O RG B ...

  • Extron electronic PVS 300 - page 5

    1-3 PoleV ault Systems Installation • Introduction — Planning Befor e you Begin Installation - Planning Before installation is started, several major factors must be consider ed to ensure that the overall installation is as smooth and trouble fr ee as possible, and that the final finished project meets the needs of the customers, users, audie ...

  • Extron electronic PVS 300 - page 6

    PoleV ault Systems Installation • Introduction — Planning 1-4 Intr oduction — Planning, cont’d • Lighting  T ype and contr ol (important for projector image viewing)  Ambient light from windows Student Desks Teacher’s Desk TV / VCR / DVD Inputs Screen/White Board Location Windows MLC Controller Location PVT A/V Wallplate Location ...

  • Extron electronic PVS 300 - page 7

    1-5 PoleV ault Systems Installation • Introduction — Planning • V iewing obstructions  Pillars, furniture etc., window locations for glar e reduction, obstructions between pr ojector and screen c. Location of MediaLink Contr oller and W all Plates • Forward and side r each (for full details refer to a copy of "ADA Standards for Acce ...

  • Extron electronic PVS 300 - page 8

    PoleV ault Systems Installation • Introduction — Inventory Overview 1-6 Intr oduction — Inventory Overview UPB 25 White 60-773-03 UPB 25 Universal Projector Bra cke t PCM 240 Projector Ceiling Mount PCM 240 White 60-772-03 (4)T ur nbuc kles (5) Lag ey es screws (5) Concrete anchors (2) Cable clamps , Gal Steel (1) Safety wire (15 ft 1/8” di ...

  • Extron electronic PVS 300 - page 9

    1-7 PoleV ault Systems Installation • Introduction — Inventory Overview PVT CV D W allplate PVT CV D White 60-819-13 (1) Mud ring (2) Dog legs (2) Dog leg screws (2) PVT mounting screws (1) Decora ® F aceplate (2) F aceplate screws *P ar t #’ s 42-109-03 and 42-110-03 contain 3 or 4 P oleV ault W allplates, according to type ordered. P oleV ...

  • Extron electronic PVS 300 - page 10

    Intr oduction — Inventory Overview , cont’d 1-8 PoleV ault Systems Installation • Introduction — Inventory Overview 1-8 N If any items in the PoleV ault System boxes are damaged or missing, contact the Extr on T echnical Hotline (see rear cover for contact numbers). PV SI 3C LP Speakers PV SI 3C LP White 42-103-13 (2) C-rings (8) C-ring att ...

  • Extron electronic PVS 300 - page 11

    1-9 PoleV ault Systems Installation • Introduction — Inventory Overview 1-9 b. Items not included The following items are not included. However , input and display devices are essential parts of the system, and at any installation they may vary depending on their use. This list suggests various devices that may be used. • Projector (or displa ...

  • Extron electronic PVS 300 - page 12

    PoleV ault Systems Installation • Introduction — Inventory Overview 1-10 Intr oduction — Inventory Overview , cont’d d. Installation tools T o aid the professional installer , this checklist gives the tools recommended to complete the installation. T ools should include, but are not confined to: • Laser level, or two levels (large for sc ...

  • Extron electronic PVS 300 - page 13

    2-1 PoleV ault Systems Installation • Installation Overview Installation Overview Installation Overview This overview outlines the basic steps for installing the PoleV ault System. Detailed description of these steps is given in five sections, Stages One though Five. N Additional installation hardware is needed and should be supplied by the inst ...

  • Extron electronic PVS 300 - page 14

    PoleV ault Systems Installation • Installation — Stage 1 2-2 Stage One — Install the Scr een and Pr ojector Stage 1 This stage involves installing the three pieces of har dwar e shown below . Ca bl e Access Cutout (install this end uppe rm ost) Threaded at both ends PMP Projector Mounting Pole T -bar Securing Screws (4) Pipe Adapter Plate Lo ...

  • Extron electronic PVS 300 - page 15

    2-3 PoleV ault Systems Installation • Installation — Stage 1 1. Mark screen location a. Mark the center line and the outer edges of screen. T When marking the location of screens, devices, or site for installing transmitters and MediaLink control devices, use painters’ tape to avoid wall surface damage. When marking the center line of the scr ...

  • Extron electronic PVS 300 - page 16

    PoleV ault Systems Installation • Installation — Stage 1 2-4 Installation — Stage One, cont’d e. Using suitable screws, mount the pr ojector onto the lower portion of the UPB 25 (the projector bracket, see b in step 2d ’s drawing). Align it so the security flange is at the rear . A minimum of three arms need to be attached to the project ...

  • Extron electronic PVS 300 - page 17

    2-5 PoleV ault Systems Installation • Installation — Stage 1 4. Cut the ceiling tile a. Mark the location of the PCM 240 on the T -bar , before removing it. This aids putting it back in the corr ect location when the tile is replaced. T Mark the screen dir ection on back of the tile (e.g. with an arrow or “to fr ont”) to help orientation of ...

  • Extron electronic PVS 300 - page 18

    PoleV ault Systems Installation • Installation — Stage 1 2-6 Installation — Stage One, cont’d 6. Secure the Pr ojector Ceiling Mount to the ceiling a. Attach the four turnbuckles to the mounting plate, one at each corner . C DO NOT r est or lean on the mounting plate or suspended ceiling when attaching turnbuckles, tie wire, or when drillin ...

  • Extron electronic PVS 300 - page 19

    2-7 PoleV ault Systems Installation • Installation — Stage 1 T Install any optional power outlets in the 2 gang opening on the mounting plate, towards the outside edge of the mount, so it does not interfere with the PMK 450 when installed. C For safety , all wiring of the electrical boxes and accessories should be completed after the plate is f ...

  • Extron electronic PVS 300 - page 20

    PoleV ault Systems Installation • Installation — Stage 2 2-8 Stage T wo — Install the W all Plates and MLC 104 IP Stage 2 This stage involves installing the devices shown below . AU DIO IN L R VIDEO IN A udio and Video input connectors A udio and Video output por t (at rear) PVT CV D AUDIO IN L R VIDEO IN Mounting screws (2) Decora F aceplate ...

  • Extron electronic PVS 300 - page 21

    2-9 PoleV ault Systems Installation • Installation — Stage 2 PVT transmitter installation • CA T 5 T568A signal transmission cables (connects PVT’s to PVS 204SA switcher) MLC 104 IP Plus installation • MLC power and RS-232 control cable (connects the MLC to the MLC/Power contr ol port on the PVS 204SA switcher) • IR/RS-232 communication ...

  • Extron electronic PVS 300 - page 22

    PoleV ault Systems Installation • Installation — Stage 2 2-10 Stage T wo — Install the W allplates and MLC 104 IP Plus N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the devices’ user manuals for details. 1. Install mud rings N These devices can be installed using the supplied mud ring ...

  • Extron electronic PVS 300 - page 23

    2-11 PoleV ault Systems Installation • Installation — Stage 2 2. Pull cables The following cables need to be installed: • CA T 5 cables for signal transmission from the A/V W all plates to the PVS 204SA. N For PVT RGB D Wall plates, two CA T 5 signal cables for each input are needed. Maximum distance from the PVS 204SA to the Wall plates is 1 ...

  • Extron electronic PVS 300 - page 24

    PoleV ault Systems Installation • Installation — Stage 2 2-12 Installation — Stage T wo, cont’d 3. Install wall plates a. Connect the CA T 5 cables to the rear of the input devices (for RGB devices, cable labeled A to port A, cable B to port B). b. Mount each device into the mud ring. c. Attach the supplied Decora faceplate. d. Label the De ...

  • Extron electronic PVS 300 - page 25

    2-13 PoleV ault Systems Installation • Installation — Stage 2 4. Install MediaLink Controller T Before cabling and installing the MLC 104 IP Plus, locate and write down the MAC address of the device for configuring the IP address. The 12 character alphanumeric address (e.g., 00-05-A6-03-9G-H4) can be found on a label on the rear of the contr o ...

  • Extron electronic PVS 300 - page 26

    PoleV ault Systems Installation • Installation — Stage 2 2-14 Installation — Stage T wo, cont’d b. Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector contr ol. c. Connect a CA T 5, 5e, or 6 straight through cable to the MLC ‘s RJ-45 jack. W DO NOT connect the MLC’ s RJ-45 jack to the PVS 204SA ...

  • Extron electronic PVS 300 - page 27

    2-15 PoleV ault Systems Installation • Installation — Stage 2 Extron MLC 104 IP Plus Rotate lo ck ing ar m and insert into wa ll opening. OFF ON OFF ON Extron CONFIG DISPLAY MLC 104 IP Plus VOLUME 1 2 3 4 ON OFF VCR DV D PC Extron MR 200 Modular Mud Ring 4e Secure the MLC 104 IP Plus to the mud ring The connections between the MLC 104 IP Plus a ...

  • Extron electronic PVS 300 - page 28

    PoleV ault Systems Installation • Installation — Stage 3 2-16 Stage Thr ee — Install the PV SI 3C LP Ceiling Speakers Stage 3 This stage involves installing the devices shown below . Where it goes: Installs in ceiling tiles at predetermined location for best acoustics. Connects to switcher . What it does: Receives and outputs audio signal fro ...

  • Extron electronic PVS 300 - page 29

    2-17 PoleV ault Systems Installation • Installation — Stage 3 N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the device’ s user manual for details. 1. Cut ceiling tile If installing PV SI 3C LP speakers, do the following: a. Remove the ceiling tiles where the speakers ar e to be installe ...

  • Extron electronic PVS 300 - page 30

    PoleV ault Systems Installation • Installation — Stage 3 2-18 Installation — Stage Thr ee, cont’d e. Loosen the four screws on the fr ont baffle (counter clockwise) 1/2 turn (see figure, A) and turn the doglegs to lock onto the C-ring. T ighten down the front screws (see gure, B). T Use a handheld screwdriver , as a power ed screwdrive ...

  • Extron electronic PVS 300 - page 31

    2-19 PoleV ault Systems Installation • Installation — Stage 3 c. T o terminate the cable, strip the end of the cable 0.2" (5 mm) and secure the wir es into the supplied 4-pole captive screw connector . d. Plug the 4-pole connector into the speaker terminal and replace and secur e the plenum cover N The correct speaker impedance loading mus ...

  • Extron electronic PVS 300 - page 32

    PoleV ault Systems Installation • Installation — Stage 3 2-20 Installation — Stage Thr ee, cont’d 5. Finish speaker installation a. Install/replace the speaker grill on the fr ont of the speaker , using the supplied adhesive tabs (putty) to secure it in place. b. Repeat cabling and final installation steps for all speakers, connecting the ...

  • Extron electronic PVS 300 - page 33

    2-21 PoleV ault Systems Installation • Installation — Stage 4 Stage 4 This stage covers installing the devices shown below . LR AU X/MIX IN 1B 1A I N P U T S O U T P U T S 2B 2A 4 3 RS-232 MLC/IR DC VO L 4/8 Ohms AMPLIFIED OUTPUTS VO L/MUTE Tx AB C Rx IR 12V 10V POWER 12V 3A MAX US LISTED 17TT AU DIO/VIDE O APPARA TU S ® RGB VIDEO RGB VIDEO ST ...

  • Extron electronic PVS 300 - page 34

    PoleV ault Systems Installation • Installation — Stage 4 2-22 Installation — Stage Four , cont’d N The installation must conform to national and local electrical codes, and UL r equirements. Refer to the device’ s user manual for details. 1. Pull the cables a. Loosen the PCM 240 set screws and r emove the PMP . b. Gather all the cables fr ...

  • Extron electronic PVS 300 - page 35

    2-23 PoleV ault Systems Installation • Installation — Stage 4 3. Install the PVS 204SA switcher a. Pass two 4-40 x 3/16" screws up thr ough the PMK’s bottom plate into the holes in the base of the switcher , and secure it in place at the left fr ont of the bottom plate. N Do not install the rubber feet on the switcher when installing the ...

  • Extron electronic PVS 300 - page 36

    PoleV ault Systems Installation • Installation — Stage 4 2-24 Installation — Stage Four , cont’d L R AU X/MIX IN 1B 1A I N P U T S O U T P U T S 2B 2A 4 3 RS-232 MLC/IR DC VO L 4/8 Ohms AMPLIFIED OUTPUTS VO L/MUTE Tx AB C Rx IR 12V 10V POWER 12V 3A MAX US LISTED 17TT AU DIO/VIDE O APP ARATU S ® RGB VIDEO RGB VIDEO STEREO ON DUAL MONO HIGH ...

  • Extron electronic PVS 300 - page 37

    2-25 PoleV ault Systems Installation • Installation — Stage 4 FRONT REAR Rear Plate 4c Attach and screw down r ear plate 4d Replace projector on the adjuster plate b. Align the bottom plate lugs with the slots in the top plate and slide up and into place. c. Attach the rear plate to secur e the PMK 450. Ensure the power cable exits via the cabl ...

  • Extron electronic PVS 300 - page 38

    PoleV ault Systems Installation • Installation — Stage 5 2-26 Stage Five — Congur e the System Stage 5 Items needed to help complete this stage: • Laptop (or PC) with a network connection • GC 2 conguration program (download from www .extron.com ) • MLC 104 IP Plus User ’ s Manual • Projector manufacturer ’s user ’s manual ...

  • Extron electronic PVS 300 - page 39

    2-27 PoleV ault Systems Installation • Installation — Stage 5 1d Select MLC 104 IP Plus/PoleV ault System from the dr op down box d. Select the MLC 104 IP Plus/PoleV ault system from the drop-down box. Follow the instructions on the help page. e. T o move to the next page (shown in the yellow box), click the NEXT button above the drop-down box. ...

  • Extron electronic PVS 300 - page 40

    PoleV ault Systems Installation • Installation — Stage 5 2-28 Installation — Stage Five, cont’d 2c Check that an image is present, adjust as needed. 2. T est the system a. Ensure power is supplied to the PVS 204SA switcher , and power on the MLC 104 IP Plus. b. Connect all the input devices (e.g., PC, DVD, document camera, etc.) to the tran ...

  • Extron electronic PVS 300 - page 41

    2-29 PoleV ault Systems Installation • Installation — Stage 5 2e Set MLC volume to maximum, and adjust the level on the switcher FRONT REAR F ront Plate Cable from power source Tighten F ront and Rear Plate Screws (4) and Side Screws (2) 3a Replace the front plate and 3b tighten down the screws on the mounting kit d. T est the contr oller ’s ...

  • Extron electronic PVS 300 - page 42

    PoleV ault Systems Installation • Optional Accessory Installation 2-30 Optional Accessory Installation — PPC 25 1. Connect sensor to paging speaker a. Open the top of the Priority Page Sensor . b. Loop (only) one of the Paging speaker wire leads ar ound the top (open) part of the Sensor . Either speaker wire will work. Leave the other speaker w ...

  • Extron electronic PVS 300 - page 43

    Specications For detailed specications and warranty information of the PoleV ault System components, refer to the device manuals, or the product pages at www .extron.com. Mounting hardwar e PCM 240 Mounting ........................................ Dr op ceiling mount Enclosure type ............................... 14 gauge steel/powder coated ...

  • Extron electronic PVS 300 - page 44

    PoleV ault Systems Installation • Reference Information 2-32 Installation — Refer ence Information, cont’d Devices PVS 204SA External power supply ................. 100 V AC to 240 V AC, 50/60 Hz, external, autoswitchable; to 12 VDC, 3 A, r egulated Power input requir ements ........... 12 VDC, 0.97 A (typical) T emperatur e/humidity ........ ...

  • Extron electronic PVS 300 - page 45

    2-33 PoleV ault Systems Installation • Installation - Reference Information Ceiling mount installation diagram (with item weights) for PoleV ault System L R AU X/MIX IN 1B 1A I N P U T S O U T P U T S 2B 2A 4 3 RS-232 MLC/IR DC VO L 4/8 Ohms AMPLIFIED OUTPUTS VO L/MUTE Tx A B C Rx IR 12V 10V POWER 12V 3A MA X US LISTED 17TT AUDIO/VIDEO AP PA RA T ...

  • Extron electronic PVS 300 - page 46

    Ex tron US A - We st Headquar te rs + 800 .6 33 .9 87 6 Insid e U S A / C anad a On ly +1 .7 14 .4 91 .1 50 0 +1 .7 14 .4 91 .1 51 7 FA X Ex tron US A - Eas t + 800 .6 33 .9 87 6 Insid e U S A / C anad a On ly +1 .9 19 .8 63 .1 79 4 +1 .9 19 .8 63 .1 79 7 FA X Ex tron EM EA + 800 .3 98 7. 66 73 Insid e E urop e On ly +3 1. 33 .4 53 .4 04 0 +3 1. 33 ...

Manufacturer Extron electronic Category Switch

Documents that we receive from a manufacturer of a Extron electronic PVS 300 can be divided into several groups. They are, among others:
- Extron electronic technical drawings
- PVS 300 manuals
- Extron electronic product data sheets
- information booklets
- or energy labels Extron electronic PVS 300
All of them are important, but the most important information from the point of view of use of the device are in the user manual Extron electronic PVS 300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Extron electronic PVS 300, service manual, brief instructions and user manuals Extron electronic PVS 300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Extron electronic PVS 300.

Similar manuals

A complete manual for the device Extron electronic PVS 300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Extron electronic PVS 300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Extron electronic PVS 300.

A complete Extron electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Extron electronic PVS 300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Extron electronic PVS 300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Extron electronic PVS 300, that we can find in the current document
3. Tips how to use the basic functions of the device Extron electronic PVS 300 - which should help us in our first steps of using Extron electronic PVS 300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Extron electronic PVS 300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Extron electronic PVS 300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Extron electronic PVS 300?

Use the form below

If you did not solve your problem by using a manual Extron electronic PVS 300, ask a question using the form below. If a user had a similar problem with Extron electronic PVS 300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)