English dropdown-ico

Manual Hatco IMPERIAL "S"

40 pages 0.7 mb
Download

Go to site of 40

Summary
  • Hatco IMPERIAL "S" - page 1

    Electric Booster W ater Heaters Imperial “S” Comp act “C” Mini-Comp act “MC” Series Inst allation & Operating Manual I&W #07.05.001.00 This manual contains import ant safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious ...

  • Hatco IMPERIAL "S" - page 2

    Form No. EBOOSTERM-0406 i CONTENTS INTRODUCTION Hatco Electric Booster W ater Heaters are designed for use with commercial dishwashers to boost the temperature of the regularly available hot water , usually 1 10°-150°F (43°-66°C) up to 180°F (82°C). W ater at 180°F (82°C) can be used as sanitizing rinse water in commercial dishwashers in ac ...

  • Hatco IMPERIAL "S" - page 3

    Form No. EBOOSTERM-0406 1 IMPORT ANT SAFETY INFORMA TION W ARNINGS T o avoid personal injury or damage to equipment, the booster heater must be inst alled by qualified, trained installers. Inst allation must conform to all local electrical and plumbing codes. Check with your local plumbing and electrical inspectors for proper procedures and codes. ...

  • Hatco IMPERIAL "S" - page 4

    Form No. EBOOSTERM-0406 2 IMPORT ANT SAFETY INFORMA TION IMPORT ANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property . W ARNINGS V alves supplied by Hatco are designed for high temperature commercial operation. Do not substitute Hatco valves with valves designed fo ...

  • Hatco IMPERIAL "S" - page 5

    Form No. EBOOSTERM-0406 3 IMPORT ANT SAFETY INFORMA TION IMPORT ANT! Read the following important safety instructions to avoid personal injury or death, and to avoid damage to the equipment or property . CAUTIONS T o prevent electrolysis or plumbing damage dielectric couplings should be used in connecting dissimilar met als, such as galvanized to c ...

  • Hatco IMPERIAL "S" - page 6

    Form No. EBOOSTERM-0406 4 MODEL DESCRIPTIONS ALL MODELS Hatco Electric W ater Booster Heaters are available in three models: Imperial, Compact and Mini- Compact. All standard models include a booster heater with low-water cut-off system, temperature/pressure relief valve, pressure reducing valve with built-in high pressure bypass, two temperature/p ...

  • Hatco IMPERIAL "S" - page 7

    Form No. EBOOSTERM-0406 5 SPECIFICA TIONS kW V olts* Phase Amp Draw Breaker or Copper Conduit L1 L2 L3 Fuse Size Wire Size Size 4 208 1 19 19 - 30 10 1/2" (13 mm) 240 1 17 17 - 30 10 1/2" (13 mm) 480 1 8 8 - 15 14 1/2" (13 mm) 5 208 1 24 24 - 30 10 1/2" (13 mm) 240 1 21 21 - 30 10 1/2" (13 mm) 480 1 10 10 - 15 14 1/2" ...

  • Hatco IMPERIAL "S" - page 8

    Form No. EBOOSTERM-0406 6 SPECIFICA TIONS Wire size is based on THHN wire for branch circuit protection at .91 derate factor . Circuit breakers and fused disconnects are to be mounted remote and wired by contractor . Sizes are based on the 2002 NEC table 310-16. Conduit size based on conductors plus ground wire sizing per T able C1 from Appendix C. ...

  • Hatco IMPERIAL "S" - page 9

    Form No. EBOOSTERM-0406 7 SPECIFICA TIONS kW V olts* Phase Amp Draw Breaker or Copper Conduit L1 L2 L3 Fuse Size Wire Size Size 36 208 1 173 173 - 225 4/0 1-1/2" (38 mm) 208 3 100 100 100 125 1 1-1/4" (32 mm) 240 1 150 150 - 200 3/0 1-1/2" (38 mm) 240 3 86.7 86.7 86.7 125 1 1-1/4" (32 mm) 380 3 54.7 54.7 54.7 70 4 1" (25 mm ...

  • Hatco IMPERIAL "S" - page 10

    Form No. EBOOSTERM-0406 8 SPECIFICA TIONS SIZING CHART FOR LOW-TEMP DISHMACHINES BOOSTERS RA TED A T 30°F (16°C) RISE Dishwasher Model Number Electric Comp act Imperial Booster Booster American Dish AH, AH-3D, AH-3D-S, AHC, AHC-3D, AHC-3D-S, ET -A, ET-AF , ET -AH, Service ET -A-M, ET -AH-M, ET-A-3, ET -AH-3, L-90-3D, L-90-3D-K, L-90-3D-K-S, L-90- ...

  • Hatco IMPERIAL "S" - page 11

    Form No. EBOOSTERM-0406 9 SPECIFICA TIONS SIZING CHART FOR LOW-TEMP DISHMACHINES (CONTINUED) BOOSTERS RA TED A T 30°F (16°C) RISE Dishwasher Model Number Electric Comp act Imperial Booster Booster Jackson Conserver 24L T , 200L T , ES1000, (Ecolab/Jackson) . . . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . . . . .S-6 Conserver 1, Cons ...

  • Hatco IMPERIAL "S" - page 12

    Form No. EBOOSTERM-0406 10 SPECIFICA TIONS BOOSTER HEA TER SIZING CHART ELECTRIC ELECTRIC COMP ACT BOOSTER IMPERIAL BOOSTER Dishwasher Model Number T emperature Rise T emperature Rise 40°F (22°C) 70°F (39°C) 40°F (22°C) 70°F (39°C) Adamation CSL-1390, CA-2, CA-3, CA-4, SLAP 44 . . . . . . . . . . . . . . . . . .C-39 . . . . . .(2)C-36 . . . ...

  • Hatco IMPERIAL "S" - page 13

    Form No. EBOOSTERM-0406 11 SPECIFICA TIONS BOOSTER HEA TER SIZING CHART (CONTINUED) ELECTRIC ELECTRIC COMP ACT BOOSTER IMPERIAL BOOSTER Dishwasher Model Number T emperature Rise T emperature Rise 40°F (22°C) 70°F (39°C) 40°F (22°C) 70°F (39°C) CMA Dishmachines CMA-180 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Hatco IMPERIAL "S" - page 14

    Form No. EBOOSTERM-0406 12 SPECIFICA TIONS BOOSTER HEA TER SIZING CHART (CONTINUED) ELECTRIC ELECTRIC COMP ACT BOOSTER IMPERIAL BOOSTER Dishwasher Model Number T emperature Rise T emperature Rise 40°F (22°C) 70°F (39°C) 40°F (22°C) 70°F (39°C) Jackson JP-24, JP-24B, JP-24F , JP-24BF . . . . . . . . . . . . . . . . . . . . . . . .C-4 . . . . ...

  • Hatco IMPERIAL "S" - page 15

    Form No. EBOOSTERM-0406 13 SPECIFICA TIONS BOOSTER HEA TER SIZING CHART (CONTINUED) ELECTRIC ELECTRIC COMP ACT BOOSTER IMPERIAL BOOSTER Dishwasher Model Number T emperature Rise T emperature Rise 40°F (22°C) 70°F (39°C) 40°F (22°C) 70°F (39°C) S tero SCT -44-10-L W , SCT -44-L W , SCT -66S-L W , SCT -76S-L W , SCT -76SC-L W , SCT-90S-L W . ...

  • Hatco IMPERIAL "S" - page 16

    Form No. EBOOSTERM-0406 14 SPECIFICA TIONS CAP ACITY - IMPERIAL “S” SERIES S torage capacity is 16 gallons (61 liters). Model kW 40°F (22°C) Rise 70°F (39°C) Rise Shipping Weight S-6 6 60 gph (227 lph) 34 gph (129 lph) 200 lbs. (91 kg) S-7 7 70 gph (265 lph) 40 gph (151 lph) 200 lbs. (91 kg) S-9 9 90 gph (341 lph) 52 gph (197 lph) 200 lbs. ...

  • Hatco IMPERIAL "S" - page 17

    Form No. EBOOSTERM-0406 15 SPECIFICA TIONS DIMENSIONS - IMPERIAL “S” SERIES DIMENSIONS - COMP ACT “C” SERIES 4 to 18 kW DIMENSIONS - COMP ACT “C” SERIES 24 to 57 kW ...

  • Hatco IMPERIAL "S" - page 18

    Form No. EBOOSTERM-0406 16 SPECIFICA TIONS DIMENSIONS - MINI-COMP ACT “MC” SERIES INST ALLA TION LOCA TION For the most effective operation, inst all the booster heater as close as possible to the commercial dishwasher . The location must have a solid foundation along with being clean and dry . Adequate front clearance is required to allow for ...

  • Hatco IMPERIAL "S" - page 19

    Form No. EBOOSTERM-0406 17 INST ALLA TION ALL MODELS Booster Heaters are shipped with most components pre-assembled. Care should be taken when unpacking shipping carton to avoid damage to unit and components enclosed. Component s are shipped with the heater unit. (See Figure 7.) 1. Remove unit from box. 2. Remove information packet. T o prevent del ...

  • Hatco IMPERIAL "S" - page 20

    Form No. EBOOSTERM-0406 18 INST ALLA TION Figure 7. Components Shipped with the Heater Unit Leg Mounting Bracket s with Hardware T emperature/Pressure Gauge T emperature Pressure Relief V alve One set of four legs supplied with all Imperial and Mini- Compact Booster Heaters. (All Compact 4-57 kW unit s supplied with either a set of legs or mounting ...

  • Hatco IMPERIAL "S" - page 21

    Form No. EBOOSTERM-0406 19 INST ALLA TION W ARNING T o assure proper operation and avoid a possible unsafe condition, the booster heater must be inst alled in a horizontal position with the base p arallel to the floor and the inlet connection at the lowest point. W ARNING This product cont ains fiberglass, a product known to the st ate of Californi ...

  • Hatco IMPERIAL "S" - page 22

    Form No. EBOOSTERM-0406 20 INST ALLA TION CAUTION T o assure proper operation do not use an anti- siphon or check valve on the incoming water line. PRESSURE REDUCING V AL VE CAUTION If water supply pressure to the booster inlet is over 20 p si (138 kPa) during flow, inst all Hatco pressure reducing valve with built-in byp ass, Hatco p art number 03 ...

  • Hatco IMPERIAL "S" - page 23

    Form No. EBOOSTERM-0406 21 INST ALLA TION Inlet Refer to Figure 8, 9, 10, 1 1 or 12. 1. Connect the booster water inlet to a hot water supply line from the regular water heater . W ater temperature from the regular water heater should be 1 10° or 140°F (43° or 60°C) and should not exceed 160°F (71°C). Minimum temperature differential between ...

  • Hatco IMPERIAL "S" - page 24

    Form No. EBOOSTERM-0406 22 INST ALLA TION Figure 10. Plumbing Connections - Compact Series 4-18 kW Figure 9. Plumbing Connections - T wo Imperial Models Connected in Series T emperature/Pressure Gauge 3/4" Gate or Ball V alve * Discharge from T/P Relief V alve. Air gap must comply with plumbing code. Shock Absorber for water hammer † T emper ...

  • Hatco IMPERIAL "S" - page 25

    Form No. EBOOSTERM-0406 23 INST ALLA TION Figure 12. Plumbing Connections - Mini-Compact Models Figure 13. Booster Heaters with optional Back Pressure V alve T emperature/Pressure Gauge 3/4" Gate or Ball V alve * T emperature/Pressure Gauge Discharge from T/P Relief V alve. Air gap must comply with plumbing code. Shock Absorber for water hamme ...

  • Hatco IMPERIAL "S" - page 26

    Form No. EBOOSTERM-0406 24 INST ALLA TION W ARNING Hatco has always endorsed the use of safety equipment when using a booster water heater or storage-type water heater . Hatco booster heaters are shipped with a temperature/pressure relief valve at no extra charge. This valve must be inst alled into the marked opening provided in the t ank. V alves ...

  • Hatco IMPERIAL "S" - page 27

    Form No. EBOOSTERM-0406 25 INST ALLA TION ELECTRICAL-ALL SIZES AND VOL T AGES General Hatco Electric Booster W ater Heaters are available for operation on standard power systems. Check the identification decal for the proper power supply . CAUTION T o assure proper performance Hatco Electric Booster W ater Heaters are only to be connected to the sa ...

  • Hatco IMPERIAL "S" - page 28

    Form No. EBOOSTERM-0406 26 OPERA TION On/Off Switch Indicator Light Figure 17. Controls-Imperial and Compact Models SYSTEM ST ART -UP W ARNING W ater in the unit is very hot. Wear protective gloves and proper attire when operating to avoid injury . 1. Close drain pipe valve. 2. Open shutoff valve to primary water supply . W ater temperature at inle ...

  • Hatco IMPERIAL "S" - page 29

    Form No. EBOOSTERM-0406 27 MAINTENANCE Figure 19. Thermost at Adjustment GENERAL W ARNING T o avoid any injury or damage to the booster heater turn the power OFF at the disconnect switch/circuit breaker and allow to cool before performing any maintenance or adjustment s. THERMOST A T Thermost at Adjustment The thermostat is factory calibrated to pr ...

  • Hatco IMPERIAL "S" - page 30

    Form No. EBOOSTERM-0406 28 MAINTENANCE BLENDED PHOSPHA TE TREA TMENT SYSTEM (OPTIONAL) The Blended Phosphate W ater T reatment System reduces mineral scale by introducing a measured amount of polyphosphate into the water . Cartridges supplied have a usage rating of 100,000 gallons (378,541 liters) of water . When the cartridge is depleted use the f ...

  • Hatco IMPERIAL "S" - page 31

    Form No. EBOOSTERM-0406 29 ACCESSORIES Figure 21. Optional S tainless S teel Adjustable Legs ST AINLESS STEEL ADJUST ABLE LEGS 1. Carefully place unit on its side. CAUTION Do not lay unit on the side with the control p anel or damage to unit could occur . 2. Thread the adjustable legs into the existing leg holes on the bottom of the unit. (See Figu ...

  • Hatco IMPERIAL "S" - page 32

    Form No. EBOOSTERM-0406 30 TROUBLESHOOTING W ARNING T o avoid any injury or damage, the booster heater must only be serviced by qualified personnel. W ARNING T o avoid any injury or damage to the booster heater turn the power OFF at the disconnect switch/circuit breaker and allow to cool before performing any maintenance. GENERAL IMPORT ANT! Many t ...

  • Hatco IMPERIAL "S" - page 33

    Form No. EBOOSTERM-0406 31 TROUBLESHOOTING W ater reaches 180°F (82°C) but does not last through the entire dishwasher operation. Low incoming water temperature. Incoming water temperature drops. Flow pressure is too high. Booster heater may be undersized. Incorrect voltage. Unit may have been energized without water (dry fired). Fuses may be blo ...

  • Hatco IMPERIAL "S" - page 34

    Form No. EBOOSTERM-0406 32 TROUBLESHOOTING W ARNING T o avoid any injury or damage, the booster heater must only be serviced by qualified personnel. W ARNING T o avoid any injury or damage to the booster heater turn the power OFF at the disconnect switch/circuit breaker and allow to cool before performing any maintenance. Gauge(s) not working prope ...

  • Hatco IMPERIAL "S" - page 35

    Form No. EBOOSTERM-0406 33 TROUBLESHOOTING T emperature limit set too low . Thermostat set too high. Incoming water temperature too high causing nuisance tripping of high temperature limit switch. Loose connections or wire connection has insulation under crimp. Low voltage. Probe may be fouled. Contactor(s) may be bad. If booster heater is not over ...

  • Hatco IMPERIAL "S" - page 36

    Form No. EBOOSTERM-0406 34 HA TCO LIMITED W ARRANTY 1. PRODUCT W ARRANTY Hatco warrants the product s that it manufactures (the “Products”) to be free from defect s in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco’ s writte ...

  • Hatco IMPERIAL "S" - page 37

    Form No. EBOOSTERM-0406 35 NOTES ...

  • Hatco IMPERIAL "S" - page 38

    Form No. EBOOSTERM-0406 36 NOTES ...

  • Hatco IMPERIAL "S" - page 39

    Form No. EBOOSTERM-0406 37 NOTES ...

  • Hatco IMPERIAL "S" - page 40

    HA TCO CORPORA TION P .O. Box 340500, Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Parts & Service Fax (800) 690-2966 Int’l. Fax (414) 671-3976 www .hatcocorp.com HA TCO AUTHORIZED P ARTS DISTRIBUT ORS Printed in U.S.A. April 2006 ALABAMA Jones McLeod Appl. Svc. Birmingham 205-251-0159 ARIZONA Auth. Comm. Food Equip. Phoenix ...

Manufacturer Hatco Category Water Heater

Documents that we receive from a manufacturer of a Hatco IMPERIAL "S" can be divided into several groups. They are, among others:
- Hatco technical drawings
- IMPERIAL "S" manuals
- Hatco product data sheets
- information booklets
- or energy labels Hatco IMPERIAL "S"
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hatco IMPERIAL "S".

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hatco IMPERIAL "S", service manual, brief instructions and user manuals Hatco IMPERIAL "S". Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hatco IMPERIAL "S".

Similar manuals

A complete manual for the device Hatco IMPERIAL "S", how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hatco IMPERIAL "S" by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hatco IMPERIAL "S".

A complete Hatco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hatco IMPERIAL "S" - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hatco IMPERIAL "S", FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hatco IMPERIAL "S", that we can find in the current document
3. Tips how to use the basic functions of the device Hatco IMPERIAL "S" - which should help us in our first steps of using Hatco IMPERIAL "S"
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hatco IMPERIAL "S"
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hatco IMPERIAL "S" in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hatco IMPERIAL "S"?

Use the form below

If you did not solve your problem by using a manual Hatco IMPERIAL "S", ask a question using the form below. If a user had a similar problem with Hatco IMPERIAL "S" it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)