-
Samsung SRP-770II - page 1
KA04-00019E Rev. 1.02 ٻ ڌ ٻ USER’S MANUAL SRP-770II LABEL PRINTER www.samsungminiprinters.com ٻ ...
-
Samsung SRP-770II - page 2
ٻ ڍٻ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or ...
-
Samsung SRP-770II - page 3
ٻ ڏٻ Table of Contents 1. Unpacking & Repacking ......................................................................... 5 2. Samsung Label Printer ................................................................... 6 3. Connecting the Power Supply ...................................................... 7 4. Connecting the Interface Cable .. ...
-
Samsung SRP-770II - page 4
ٻ ڑٻ 2. Samsung Label Printer Feed Button Cover Peel-off Status Indicator Cover Open/Close Power Switch Printer Head Paper Holder Paper Guide Peel-off Sensor Paper(gap) Sensor Paper Adjuster Power Connector Interface Connectors [RS-232C, IEEE1284, USB] Dip Switch OvPG Auto Cutter ٻ ڒ 3. Connecting the Power Supply CAUTIONS: When ...
-
Samsung SRP-770II - page 5
ٻ ړٻ 4. Connecting the Interface Cable Universal Serial Bus (USB) ٻ Serial Interface RS-232 default setting is 19200 baud, no parity, 8 data bits and 1 stop bit ٻ Parallel Interface ٻ ٻ ٻ ڔ 5. Installing or Replacing the Paper Roll 1. Open Cover 2. Open Guides 3. Install Roll 5. Close Cover 4. Close Guides to the Width of the paper ...
-
Samsung SRP-770II - page 6
ٻ ڌڋٻ 6. Setting The Dip Switches 6-1. Setting the Dip Switches The Dip Switches are located on the bottom of the printer. The Dip Switches are used to set the Printer to perform various functions. Follow these steps when changing Dip Switches setting : 1. Turn the printer power switch off. 2. Remove the screw on the bottom of the printer and o ...
-
Samsung SRP-770II - page 7
ٻ ڌڍٻ 8. LED Display LED display indicates the printer status. 1. Green LED on - The printer waits for the data from Host (PC) in normal mode. 2. Orange LED on - It means paper gap sensing error. It becomes on when the pri nter fails to detect the paper or paper jam occurred. When fails to detect the paper correctly use Auto-Calibration functio ...
-
Samsung SRP-770II - page 8
ٻ ڌڏٻ 11. The Peel-off This function is used to separate label from liner automatically. CAUTIONS: 1) Peeler is for Label Paper only. 2) When the peeler switch is on, label is not printed before when the previous printed label is taken off from the peeler. 3) When the peeler function is not used set peeler switch off. With this switch on printe ...
-
Samsung SRP-770II - page 9
ٻ ڌڑٻ 13. Auto Cutter (Option) Auto cutter should be used for cont inuous paper only. ( i.e. roll paper) 1. Open the Dip switch cover, and make the switch 1 number 7 “On”. (Refer to printer mode setting at Chapter 6.) 2. Put a paper roll into the printer and close the cover. CAUTIONS: (Partial cut) Once the printer cut the paper, remove the ...
-
Samsung SRP-770II - page 10
ٻ ڌړٻ 15. Memory Switch Setting 1. Models : SRP-770II, SRP-780 2. Features It helps users through the setting of code pag es, serial setting, paper size and p rint density as necessary. 3. How to use ཛ Press Get Status button and it d isplays the current setting. ٻ ڌڔ ཛྷ Press Set Status button after changing the setting as you need. Then ...
-
Samsung SRP-770II - page 11
ٻ ڍڋٻ 16. Install and Uninstall Windows Driver 13.1 Download install-program from Website (1) Execute web-browser.(Ex: Internet Explorer) (2) Type http://www.bixolon.com (3) Connect website. (4) In “Quick menu”, click download button. (5) Download “SRP-770II_V3.X.X.exe” in SRP-770II section. 13.2 Install Windows Driver 13.2.1 Serial Par ...
-
Samsung SRP-770II - page 12
ٻ ڍڍٻ (5) Select interface (port) type. (6) Please click “Continue Anyway”. * If you can see this dialog, don’t worry comment of dialog. Printer and driver works well. Please click “Continue Anyway” button. (7) Please reboot computer. ٻ ڍڎ 13.2.2 USB interface A. Windows 95/98/ME (1) Double click “SRP-770II_V3.X.X.exe” file. (2 ...
-
Samsung SRP-770II - page 13
ٻ ڍڏٻ (3) Click “Install” Button. (4) Select operating system type. ٻ ڍڐ (5) Select “USB” interface (port) type. (6) Please turn-off printer and turn-on printer. (7) When “Add new hardware wizard” for install “USB print support” driver pops up, click “Next” button. ...
-
Samsung SRP-770II - page 14
ٻ ڍڑٻ (8) Please click “Next” button three times. (9) When “USB print support” driver is installed, your system automatically restart after 10 seconds. (10) After the system restart, please turn-on printer. B. Windows NT/2000 (1) Double click “SRP-770II_V3.X.X.exe” file. (2) Click “Next” Button. ٻ ڍڒ (3) Click “Install” B ...
-
Samsung SRP-770II - page 15
ٻ ڍړٻ (5) Select “USB” interface (port) type. (6) Please turn-off printer and turn-on printer. * If you can see this dialog, don’t worry comment in dialog. Printer and driver work well. Please click “Yes” button. ٻ ڍڔ C. Windows XP/2003 Server (1) Double click “SRP-770II_V3.X.X.exe” file. (2) Click “Next” Button. (3) Click ...
-
Samsung SRP-770II - page 16
ٻ ڎڋٻ (4) Select operating system type. (5) Select “USB” interface (port) type. (6) Please turn-off printer and turn-on printer. * If you can see this dialog, don’t worry comment in dialog. Printer and driver work well. Please click “Continue Anyway” button. ٻ ڎڌ (7) If “Add new hardware wizard” for install “SAMSUNG SRP-770II ...
-
Samsung SRP-770II - page 17
ٻ ڎڍٻ (8) Please click “Next” button until you can see “Finish” button. *If you can see this dialog, don’t worry comment in dialog. Printer and driver work well. Please click “Continue Anyway” button. (9) Please click “Finish” button. ٻ ڎڎ 13.3 Uninstall Windows Driver (1) Click on the Start button, and then click on Settin ...
-
Samsung SRP-770II - page 18
ٻ ڎڏٻ 13.4 Printer Settings 1) Measurement: Select measurement of “T op Margin” . (Inch or millimeters) 2) T op Margin: top margin value of paper 3) Density: Select density of printing quality . (0 ~ 20) 4) Media T ype: Select paper media type. (“Black Mark” is under development) 5) Orientation: Set printing direction. 6) Speed: Set pri ...
-
Samsung SRP-770II - page 19
ٻ ڎڑٻ ૺ Specification ૻ Printing method Thermal line printing Dot density 203 dpi (8 dot/mm) Printing width 25.4 ~ 101.6 mm Paper width 38.1 ~ 104 mm Printing speed 127 mm/sec Receive Buffer Size 32K Byte Note : Printing speed can be different, dependi ng on the dat a transmission speed a n d c o m b i n a t i o n o f c o n t r o l c o ...
Do you have a question concerning Samsung SRP-770II?
Use the form below
If you did not solve your problem by using a manual Samsung SRP-770II, ask a question using the form below. If a user had a similar problem with Samsung SRP-770II it is likely that he will want to share the way to solve it.