English dropdown-ico

Manual Snapper 5201M

12 pages 0.25 mb
Download

Go to site of 12

Summary
  • Snapper 5201M - page 1

    5/2005 1 Manual No. 7100193 I.R. 6/10/2005 TP 300-5071-IR-SX-N Dealer Setup & Adjustment Instructions 520 Series Single Stage Snowthrower T ABLE OF CONTENTS: SAFETY RULES ........................................................2 SETUP PROCEDURES Quick Setup List .......................................................3 Unboxing and Assembly .... ...

  • Snapper 5201M - page 2

    520 Single Stage Snowthr ower 5/2005 2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severe personal injury or death to you, yourself or bystanders, or damage to property or equipment. This auger is capable of amputating hands and feet and throwing objects. The triangle in ...

  • Snapper 5201M - page 3

    Quick Setup List - 520 Single Stage Snowthr ower 5/2005 3 P age Setup Procedure Steps to P erform 4 Unbo x & Assemble ❏ Remov e Unit F rom Bo x. ❏ Install Discharge Chute ❏ Assemble Handle Bars (Be careful not to pinch the auger cable) ❏ Mount Clean-Out T ool in storage position on handle 5 Fill Gas T ank ❏ Fill Gas T ank 6 Lubricate ...

  • Snapper 5201M - page 4

    520 Single Stage Snowthr ower 5/2005 4 Unbo xing & Assembl y 1. Using a utility knife, open the box and remove the snowthrower. 2. Install the discharge chute on to the rotating ring located on the auger housing. Secure with the three 5/16 inch carriage bolts, flat washers and nylok nuts found in the parts bag (the bolt heads go to inside of of ...

  • Snapper 5201M - page 5

    FUEL TO OIL MIXTURE CHART (50:1) U.S. Imperial Metric Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil Gasoline 2 Cycle Oil Gallons Ounces Gallons Ounces Liters Milliliters 1 2.5 1 2.8 4 80 ml 2 5 2 5.6 8 160 ml 5 13 5 14.1 20 400 ml 520 Single Stage Snowthr ower 5/2005 5 Fill Gas T ank Fuel and Oil Mixture The snowthrower uses a two cycle engine that req ...

  • Snapper 5201M - page 6

    520 Single Stage Snowthr ower 5/2005 6 Figure 8. Grease the Discharge Chute Ring Lubricate Flange Removing Belt Co ver In order to perform proper lubrication, it is necessary to remove the Belt cover from the lower left of the snowthrower. 1. Remove the Engine Key from the switch. 2. Remove the fours screws securing the belt cover (see Figure 5). 3 ...

  • Snapper 5201M - page 7

    520 Single Stage Snowthr ower 5/2005 7 T est Run Test run the unit for several minutes. Check that the following work properly: • Primer • Choke • Recoil Starter • Electric Starter (Where Applicable) • Auger Control Cable • Kill Switch • Chute Rotator • Deflector ST AR TING THE ENGINE NOTE: The snow thrower engine is designed to ope ...

  • Snapper 5201M - page 8

    520 Single Stage Snowthr ower 5/2005 8 Figure 10. Cover Removal & Installation Insert front tabs first when reinstalling cover. Align rear tabs & side of cover when reinstalling. Lift Cover from Rear of unit Figure 9. Remove and/or loosen Cover Screws Remove two rear fasteners securing cover Remove Fuel Tank Cap Remo ving Engine Co ver Note ...

  • Snapper 5201M - page 9

    520 Single Stage Snowthr ower 5/2005 9 A uger Control Cab le Adjustment The length of the auger control cable is adjustable. However, it will seldom be necessary to change the cable length since the operating tension on the drive belt is maintained by the spring on the end of the cable. If the auger turns too slowly under heavy load or momentary sq ...

  • Snapper 5201M - page 10

    520 Single Stage Snowthr ower 5/2005 10 Service Notes ...

  • Snapper 5201M - page 11

    520 Single Stage Snowthr ower 5/2005 11 Service Notes ...

  • Snapper 5201M - page 12

    520 Single Stage Snowthr ower Manual No. 7100193 I.R. 6/10/2005 TP 300-5071-IR-SX-N 5/2005 12 Replacing the Drive Belt 1. Remove Engine Key from switch. 2. Remove belt cover (see Page 6) and the engine cover (see Page 8). 3. Move the Auger Control on the handle and slip the belt out from between the brake lever and roller and away from the idler pu ...

Manufacturer Snapper Category Snow Blower

Documents that we receive from a manufacturer of a Snapper 5201M can be divided into several groups. They are, among others:
- Snapper technical drawings
- 5201M manuals
- Snapper product data sheets
- information booklets
- or energy labels Snapper 5201M
All of them are important, but the most important information from the point of view of use of the device are in the user manual Snapper 5201M.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Snapper 5201M, service manual, brief instructions and user manuals Snapper 5201M. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Snapper 5201M.

Similar manuals

A complete manual for the device Snapper 5201M, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Snapper 5201M by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Snapper 5201M.

A complete Snapper manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Snapper 5201M - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Snapper 5201M, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Snapper 5201M, that we can find in the current document
3. Tips how to use the basic functions of the device Snapper 5201M - which should help us in our first steps of using Snapper 5201M
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Snapper 5201M
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Snapper 5201M in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Snapper 5201M?

Use the form below

If you did not solve your problem by using a manual Snapper 5201M, ask a question using the form below. If a user had a similar problem with Snapper 5201M it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)