English dropdown-ico

Manual TeleWell TW-EAV510

66 pages Not applicable
Download

Go to site of 66

Summary
  • TeleWell TW-EAV510 - page 1

    TeleWell TW - EAV510 XDSL ROUTER RELEASE 1. 3 USER MANUAL ...

  • TeleWell TW-EAV510 - page 2

    2 CONTENTS Device Installation ....................................................................................................................... 4 Power on Router ......................................................................................................................... 4 Factory Reset Button .................................... ...

  • TeleWell TW-EAV510 - page 3

    3 Multicast .................................................................................................................................... 47 Wireless .................................................................................................................................... 48 Basic ................................................... ...

  • TeleWell TW-EAV510 - page 4

    4 11 Device Installation The TW -EAV 510 connects two separate physical interfaces, an xDSL (WAN) and an Ethernet (LAN) interface. Place the Router in a location where it can be connected to the various devices as well as to a power source. The Router should not be located where it will be exposed to moisture or excessive heat. Make sure the cables ...

  • TeleWell TW-EAV510 - page 5

    5 Network Connections Connect xDSL Line Use the xDSL cable included with the Router to connect it to a telephone wall socket or receptacle. Plug one end of the cable into the xDSL port (RJ-11 receptacle) on the rear panel of the Router and insert the other end into the RJ-11 wall socket. If you are using a low pass filter device, follow the instruc ...

  • TeleWell TW-EAV510 - page 6

    6 Web -based Configuration Utility Connect to the Router The default IP address for xDSL MODEM is: 192.168.0. 254 ; The Subnet Mask is ： 255.255.255.0. Users can configure xDSL MODEM through an Internet browser. xDSL MODEM can be used as gateway and DNS server; users need to set the computer’s TCP/IP protocol as follow: 1. Set the computer IP a ...

  • TeleWell TW-EAV510 - page 7

    7 Device Info To access the Device Info window, click either the Device Info or Summary button in the Device Info directory. The following page opens: ...

  • TeleWell TW-EAV510 - page 8

    8 Summary To access the Router’s first Summary window, click the Summary button in the Device Info directory. This window displays the current status of your DSL connection, including the software version, LAN IP address, and DNS server address. WAN To access the WAN Info window, click the WAN button in the Device Info directory. This window disp ...

  • TeleWell TW-EAV510 - page 9

    9 Statistics The Statistics menu contains statistical information about the LAN, WAN service, and Optical. Select Statistics in the Device Info menu to open the Statistics submenu. LAN The LAN window displays the statistics for the information received and transmitted over the LAN interface. Click LAN in the Statistics submenu to open the LAN windo ...

  • TeleWell TW-EAV510 - page 10

    10 xTM To access the Device Info – xTM window, click the x TM button in the Device Info directory. This read-only window displays xTM info. xDSL To access the Device Info – XDSL window, click the xDSL button in the Device Info directory. This read-only window displays xDSL info. ...

  • TeleWell TW-EAV510 - page 11

    11 ...

  • TeleWell TW-EAV510 - page 12

    12 Route To access the Device Info – Route window, click the Route button in the Device Info directory. This read-only window displays routing info. ARP To access the Device Info – ARP window, click the ARP button in the Device Info directory. This read-only window displays Address Resolution Protocol info. DHCP To access the Device Info – DH ...

  • TeleWell TW-EAV510 - page 13

    13 Advanced Setup This chapter include the more advanced features used for network management and security as well as administrative tools to manage the Router, view status and other information used to examine performance and for troubleshooting. Layer2 Interface To access the DSL ATM Interface Configuration window, click the ATM Interface button ...

  • TeleWell TW-EAV510 - page 14

    14 ATM Inter face The ATM PVC Configuration window allows you to set up ATM PVC configuration. Enter Virtual Path Identifier, and Virtual Channel Identifier. The VPI and VCI values should be provided by your ISP. This window also a llows you to select DSL Link Type, PPPoA 、 IPoA and EoA (EoA is for PPPoE, IPoE, and Bridge) Use the drop-down menu ...

  • TeleWell TW-EAV510 - page 15

    15 VDSL2 ( ptm) interface The VDSL2 (ptm) interface Configuration window enables you to add, delete, or modify up to one VDSL WAN Layer 2 interface connections. Click VDSL2 (ptm) Interface in the Layer2 Interface menu to open the VDSL(ptm) WAN Interface Configuration window VDSL WAN Configuration If you h ave selected to add or modify a VDSL interf ...

  • TeleWell TW-EAV510 - page 16

    16 ETH interface The ETH WAN Interface Configuration window enables you to add, delete, or modify up to one ETH WAN Layer 2 interface connections. Click ETH Interface in the Layer2 Interface menu to open the ETH WAN Interface Configuration window ETH WAN Configuration If you have selected to add or modify an ETH interface connection, the ETH WAN Co ...

  • TeleWell TW-EAV510 - page 17

    17 WAN Servi ce To access the Wide Area Network (WAN) Service Setup window, click the WAN Service button in the Advanced Setup directory. This window is used to configure the WAN interface. You can add and delete WAN interface on this window. If you are setting up the WAN interface for the first time, click the Add button. The WAN Service Interface ...

  • TeleWell TW-EAV510 - page 18

    18 WAN Service Configuration – PPPoE This window allows you to set the username and the password for your PPP connection. This information is obtained from your ISP. Additional settings on this window will also depend on your ISP. And you can input 2 nd IP on this page. Click the Next button to continue. ...

  • TeleWell TW-EAV510 - page 19

    19 WAN Service Configuration – IPoE This window allows you to configure the WAN IP settings. This information is obtained from your ISP. Click the Next button to continue ...

  • TeleWell TW-EAV510 - page 20

    20 WAN Service Configuration – B ridging Click the Bridge radio button on this window. Click the Next button to continue. ...

  • TeleWell TW-EAV510 - page 21

    21 LAN You can configure the LAN IP address to suit your preference. Many users will find it convenient to use the default settings together with DHCP service to manage the IP settings for their private network. The IP address of the Router is the base address used for DHCP. In order to use the Router for DHCP on your LAN, the IP address pool used ...

  • TeleWell TW-EAV510 - page 22

    22 IPv6 Autoconfig The IPv6 Autoconfig window enables you to configure the settings for the LAN interface with IPv6. Click IPv6 Autoconfig in the LAN submenu to open the IPv6 Autoconfig window; This window allows you to configure IPv6. When you are finished, click the Apply / Save button. ...

  • TeleWell TW-EAV510 - page 23

    23 Ethernet Port To access the Ethernet Port window, click the Ethernet Port button in the Advanced Setup submenu. You can configure the Media Type of Ethernet port in the new page and it will show you the Link Status of each Ethernet port. When you are finished, click the Save/Apply button NAT Virtual Servers Select Virtual Servers from the Advanc ...

  • TeleWell TW-EAV510 - page 24

    24 Port Triggering Some applications such as games, video conferencing, remote access applications and others require that specific ports in the Router's firewall be opened for access by the applications. You can configure the port settings from this screen by selecting an existing application or creating your own (Custom application). Click t ...

  • TeleWell TW-EAV510 - page 25

    25 DMZ Host Since some applications are not compatible with NAT, the Router supports use of a DMZ IP address for a single host on the LAN. This IP address is not protected by NAT and will therefore be visible to agents on the Internet with the right type of software. Keep in mind that any c lient PC in the DMZ will be exposed to various types of se ...

  • TeleWell TW-EAV510 - page 26

    26 Security To access the Security window, click the Security button in the Advanced Setup directory. The Security button appears after configuring WAN interface in PPPoA, PPPoE, IPoE or IPoA. IP Filtering The IP Filtering button appears when configuring WAN interface in PPPoA, PPPoE, IPoE or IPoA. IP Filtering - Outgoing This window allows you to ...

  • TeleWell TW-EAV510 - page 27

    27 Now default policy is ACCEPT, it means all outgoing IP traffic from LAN is allowed, but some IP traffic can be blocked by setting up filters. If you are setting up the outgoing IP filtering, click the Add button. Enter the information in the section. Explanations of parameters are described below. Click the Apply / Save button to add the entry i ...

  • TeleWell TW-EAV510 - page 28

    28 Enter the information in the section. Explanations of parameters are described below. Click the Apply / Save button to add the entry in the Active Inbound IP Filtering table. MAC fil ter The MAC Filtering window enables you to control access to and from specific MAC addresses. Select MAC Filtering from the Security submenu to open the MAC Filter ...

  • TeleWell TW-EAV510 - page 29

    29 Parental Control Use this window to deny access to specified MAC address. Time Restrictio n If you are setting up the MAC address blocking, click the Add button. MAC address is a specially formatted text string (xx:xx:xx:xx:xx:xx) that uniquely identification of a device. This section will allow users to block devices with certain MAC addresses ...

  • TeleWell TW-EAV510 - page 30

    30 URL Filter This window allows you to set up URL Filter on the Router. Choose URL List Type Exclude or Include first and click Add button. Enter the URL address and port number then click Apply / Save to add the entry to the URL filter. ...

  • TeleWell TW-EAV510 - page 31

    31 3G To access the 3G window, click the 3G button in the Advanced Setup directory. This window allows you to set up 3G on the Router. When you are finished, click on the Save/Apply button. If you want to add new 3G dongle, click driver add button, and the new page will show you how to configure a new 3G dongle. After you are finished, click on the ...

  • TeleWell TW-EAV510 - page 32

    32 ...

  • TeleWell TW-EAV510 - page 33

    33 Quality of Service QoS or Quality of Service allows your Router to help prioritize the data packet flow in your Router and network. This is very important for time sensitive applications such as VoIP where it may help prevent dropped calls. Large amounts of non-critical data can be scaled so as not to affect these prioritized sensitive real-time ...

  • TeleWell TW-EAV510 - page 34

    34 QoS Classifi cation Choose Add or Remove to configure network traffic classes. Use this window to create a traffic class rule to classify the upstream traffic, assign a queue that defines the precedence and the interface, and optionally overwrite the IP header DSCP byte. A rule consists of a class name and at least one condition. Please remember ...

  • TeleWell TW-EAV510 - page 35

    35 Routing To access the Routing windows, click the Routing button in the Advanced Setup directory. Default Gat eway Default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN in ...

  • TeleWell TW-EAV510 - page 36

    36 Static Route Click the Add button on the Routing – Static Route window to access the following window displayed on the next page. Enter the static routing information for an entry to the routing table. Click the Apply / Save button when you are finished. Policy Routing Click the Add button on the Policy Routing Setting window to access the fol ...

  • TeleWell TW-EAV510 - page 37

    37 RIP To activate RIP for the device, select the Enabled radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the 'Enabled' checkbox for the interface. Click the Save/Apply button to save the configuration, and to start or stop RIP based on th ...

  • TeleWell TW-EAV510 - page 38

    38 Dynamic DNS The Router supports Dynamic DNS (Dynamic Domain Name Service). The Dynamic DNS service allows a dynamic public IP address to be associated with a static host name in any of the many domains, allowing access to a specified host from various locations on the Internet. This is enabled to allow remote access to a host by clicking a hyper ...

  • TeleWell TW-EAV510 - page 39

    39 Note DDNS requi res that an ac count be set up wi th on e of the supported DDNS servers prior to engaging i t on the Router. This funct ion wil l not work without an accepted account with a DDNS serv er. ...

  • TeleWell TW-EAV510 - page 40

    40 DSL The DSL window enables you to configure the DSL settings of the gateway. Select DSL from the Advanced Setup menu to open the DSL Settings window If you clicked Advanced Settings in the DSL Settings window, the DSL Advanced Settings window opens ...

  • TeleWell TW-EAV510 - page 41

    41 If you clicked the Tone Selection button, the ADSL Tone Settings window opens Note: The ADSL tone settings should only be configured with the assistance of your ISP. UPNP To access the UPnP Configuration window, click the UPnP button in the Advanced Setup directory. This window allows you to Config UPnP Proxy. Click the Apply / Save button when ...

  • TeleWell TW-EAV510 - page 42

    42 DLNA Select DLNA from the Advanced Setup menu to open the DLNA window. This window allows you to config DLNA function. Click the Apply / Save button when you are finished. Storage service The Storage Service window displays Storage Device information from USB interface. Select Storage Service from the Adv anced Setup menu to open the Storage Ser ...

  • TeleWell TW-EAV510 - page 43

    43 Interface Group ing Interface Group supports multiple ports to PVC and bridging groups. Each group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button will remove the grouping and add the ungrouped interfaces to the Default ...

  • TeleWell TW-EAV510 - page 44

    44 IP Tunnel Select IP Tunnel from the Advanced Setup menu to open the IP Tunnel submenu. IPv6inIPv 4 Select IPv6in IPv4 from the IP Tun nel submenu to open the IP Tunneling - 6in4 Tunnel Configuration window If you click Add , the detail of the IP Tunneling-6in4 Tunnel Configuration window will open IPv4inIPv 6 Select IPv4in IPv6 from the IP Tun n ...

  • TeleWell TW-EAV510 - page 45

    45 IPSec To access the IPSec Tunnel Mode Connections window, click the IPSec button in the Advanced Setup directory. This window allows you to configure IPSec . Click Add New Connection to edit IPSec tunnel mode connections from this page This window allows you to advanced settings. ...

  • TeleWell TW-EAV510 - page 46

    46 Power Management The Power Management window enables you to control of Hardware to evaluate power consumption. Select Power Management from the Advance d Set up menu to open the Power Management window ...

  • TeleWell TW-EAV510 - page 47

    47 Multicast To access the IGMP Configuration window, click the Multicast button in the Advanced Setup directory. Enter IGMP protocol configuration fields if you want modify default values shown below . ...

  • TeleWell TW-EAV510 - page 48

    48 Wireless Basic The Basic menu enables you to configure basic features of the wireless LAN interface. Select Basic from the Wi re les s menu to open the basic submenu; ...

  • TeleWell TW-EAV510 - page 49

    49 Security This page allows you to configure security features of the wireless LAN interface. You may setup configuration manually or through WiFi Protected Setup(WPS) You can select to configure WEP encryption, Shared, 802.1x, WPA, and WPA2 authentication. ...

  • TeleWell TW-EAV510 - page 50

    50 MAC Filter This page can help you to allow or deny certain MAC addresses to pass through or block out. Click Add to see the following page. Enter MAC Address and click Apply / Save to add the MAC address to MAC filter. ...

  • TeleWell TW-EAV510 - page 51

    51 Wireless Bridge The Wireless Bridge menu enables you to configure wireless bridge features of the wireless LAN interface. Select Wire le ss Bri dge from the Wir el ess menu to open the wireless bridge submenu Advanced This page allows you to configure advanced wireless LAN interface. Configuring these settings may increase the performance of you ...

  • TeleWell TW-EAV510 - page 52

    52 Station Info This page shows the authenticated wireless stations and their status. Click Refresh to update the information. ...

  • TeleWell TW-EAV510 - page 53

    53 Diagnostics Diagnostics Your modem is capable of testing your DSL connection wit h access to Diagnostics . This window is used to test connectivity of the Router. Fault Management Fault Management enables you to test the connectivity of the xDSL PTM mode. Note: Fault management should only be run with assistance from your ISP. Select Fault Manag ...

  • TeleWell TW-EAV510 - page 54

    54 Management The Management directory features an array of options designed to help you get the most out of your Router. Settings To access the Settings - Backup window, click the Settings button in the Management directory. This window allows you to backup your DSL Router configurations. Click the Backup Settings button to save your Router config ...

  • TeleWell TW-EAV510 - page 55

    55 This window allows Restore DSL router settings to the factory defaults. Click the Restore DSL Settings button to r estore DSL router settings to the factory defaults. System Log The System Log windows enable you view and configure the system log of this device. Select System Log in the Management menu to open the System Log window If you clicked ...

  • TeleWell TW-EAV510 - page 56

    56 opens; Note: Configuring the system log should be done with assistance from your ISP. Security Log The System Log windows enable you view the security log of this device. Select Security Log in the Management menu to open the Security Log window; If you clicked View in the Security Log window, the Security Log information window opens; ...

  • TeleWell TW-EAV510 - page 57

    57 TR069 client The TR -069 Client window enables you to configure the ACS for this device Select TR -069 Client in the Management menu to open the TR - 069 Client -Configuration window; Internet Time To access the Time settings window, click the Internet Time button in the Management directory. This window allows you to set the Router’s time con ...

  • TeleWell TW-EAV510 - page 58

    58 Access Control To access the Access Control windows, click the Access Control button in the Management directory. Passwords This window allows you to change the password on the Router. When you are finished, click the Save/Apply button. Services The Services window enables you to enable or disable services Select Services from the Access Control ...

  • TeleWell TW-EAV510 - page 59

    59 IP Address es The IP Address Access Control mode, if enabled, permits access to local management services from IP addresses contained in the Access Control List. If the Access Control mode is disabled, the system will not validate IP addresses for incoming packets. The services are the system applications listed in the Service Control List. To a ...

  • TeleWell TW-EAV510 - page 60

    60 Input the IP Address and Subnet Mask which you want to configure, and then click Apply to enable this IP Address. Reboot To access this window, click the Reboot button in the Management directory. To save your settings and reboot the system, click the Reboot button. Tools This page will help you to diagnostic the status of your Network. You can ...

  • TeleWell TW-EAV510 - page 61

    61 Troubleshooting 1. How do I configure my TW -EAV510 Router without the CD- ROM? • Connect your PC to the Router using an Ethernet cable. • Open a web browser and enter the address http://192.168.0.254 • The default username is ‘admin’ and the default password is ‘admin’. • If you have changed the password and cannot remember it, ...

  • TeleWell TW-EAV510 - page 62

    62 Note: There might be a potential security i ssue if you disable the setting of Fir ewall on your PC. Please remem ber to turn it ba ck on onc e you hav e finis hed the whole i nstallat ion procedure and can surf on Interne t withou t any p roblem ...

  • TeleWell TW-EAV510 - page 63

    63 Glossary Numerics 10/100Base -T The most widel y used standa rd fo r Ethe rnet over t wiste d pair or copper - based computer networking. Runs at 10 Mb/s , 100 Mb /s , and 10 00 Mb/ s (1 Gb/s) respectively. A ACS Auto - Confi gurat ion Server ADSL Asymmet ric Dig ita l S ubscr ibe r Li ne ALG Appli cat ion - Level Gateway ATM Asynch rono us Tran ...

  • TeleWell TW-EAV510 - page 64

    64 E Ethernet A fami ly of fra me - based computer networki ng technologies for local area networks (LANs). F Firewall An in teg rate d c oll ecti on of s ecur ity mea sure s d e signed to prevent unauthorized electronic access to a networked computer system. G Gateway A net work nod e eq uipp ed f or int erfa cin g wi th a not her net work tha t u ...

  • TeleWell TW-EAV510 - page 65

    65 NAT Networ k Addr ess Tran slat ion Net mask The desi gnate d IP a ddress routi ng pr efix for a networ k of c omputers and devices . NIC Networ k Interface Controller NTP Networ k Ti me Pr otoco l O OAM Operat ions , Ad minis tra tio n, a nd Mai nte nance P PAP Password Authen ticati on Proto col Ping A comp uter ne twor k to ol used to te st w ...

  • TeleWell TW-EAV510 - page 66

    66 UDP User Datag ram P roto col UPnP Univer sal Plu g an d Pl ay URL Unifo rm Res ource Loc ator USB Univer sal Ser ial Bus V VCI Virt ual Cir cuit I D xDSL Very High Bit rate Digital Subscribe r Line VLAN Virt ual Loca l Ar ea Networ k VPI Virt ual Pat h I D W WAN Wide A rea N et wor k ...

Manufacturer TeleWell Category Router

Documents that we receive from a manufacturer of a TeleWell TW-EAV510 can be divided into several groups. They are, among others:
- TeleWell technical drawings
- TW-EAV510 manuals
- TeleWell product data sheets
- information booklets
- or energy labels TeleWell TW-EAV510
All of them are important, but the most important information from the point of view of use of the device are in the user manual TeleWell TW-EAV510.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TeleWell TW-EAV510, service manual, brief instructions and user manuals TeleWell TW-EAV510. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TeleWell TW-EAV510.

Similar manuals

A complete manual for the device TeleWell TW-EAV510, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TeleWell TW-EAV510 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TeleWell TW-EAV510.

A complete TeleWell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TeleWell TW-EAV510 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TeleWell TW-EAV510, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TeleWell TW-EAV510, that we can find in the current document
3. Tips how to use the basic functions of the device TeleWell TW-EAV510 - which should help us in our first steps of using TeleWell TW-EAV510
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TeleWell TW-EAV510
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TeleWell TW-EAV510 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TeleWell TW-EAV510?

Use the form below

If you did not solve your problem by using a manual TeleWell TW-EAV510, ask a question using the form below. If a user had a similar problem with TeleWell TW-EAV510 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)