English dropdown-ico

Manual Lincoln Electric SVM187-A

142 pages 3.04 mb
Download

Go to site of 142

Summary
  • Lincoln Electric SVM187-A - page 1

    SVM187-A October , 2008 Safety Depends on Y ou Lincoln arc welding and cutting equipment is designed and built with safety in mind. However , your overall safety can be increased by pr oper installation . . . and thoughtful operation on your part. DO NOT INST ALL, OPERA TE OR REP AIR THIS EQUIPMENT WITHOUT READ- ING THIS MANUAL AND THE SAFETY PRECA ...

  • Lincoln Electric SVM187-A - page 2

    SAFETY i i Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY FOR ENGINE powered equipment. 1.a. T urn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b.Operate engines in ...

  • Lincoln Electric SVM187-A - page 3

    SAFETY ii ii Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY FUMES AND GASES can be dangerous. 5.a. Welding may produce fumes and gases hazardous to health. Avoid breathing these fumes and gases.When welding, keep your head out of the fume. Use enough ventilation and/or exhaust at the arc ...

  • Lincoln Electric SVM187-A - page 4

    SAFETY iii iii Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY Jan ‘07 FOR ELECTRICALL Y powered equipment. 8.a. T urn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, ...

  • Lincoln Electric SVM187-A - page 5

    SAFETY iv iv Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY Mar ‘93 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté gén? ...

  • Lincoln Electric SVM187-A - page 6

    SAFETY v v Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY Electromagnetic Compatibility (EMC) Conformance Products displaying the CE mark are in conformity with European Community Council Directive of 3 May 1989 on the approximation of the laws of the Member States relating to electromagn ...

  • Lincoln Electric SVM187-A - page 7

    SAFETY vi vi Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY Electromagnetic Compatibility (EMC) The size of the surrounding area to be considered will depend on the structure of the building and other activities that are taking place. The surrounding area may extend beyond the boundaries ...

  • Lincoln Electric SVM187-A - page 8

    - MASTER T ABLE OF CONTENTS FOR ALL SECTIONS - RETURN TO MAIN INDEX Page S a f e t y ........................................................................... i - i v I n s t a l l a t i o n .................................................................. S e c t i o nA O p e r a t i o n ......................................................... ...

  • Lincoln Electric SVM187-A - page 9

    A-1 A-1 SAE-400 SEVERE DUTY T ABLE OF CONTENTS - INST ALLA TION SECTION Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC I n s t a l l a t i o n ............................................................................. A - 1 T e c h n i c a l S p e c i f i c a t i o n s .................................... ...

  • Lincoln Electric SVM187-A - page 10

    INST ALLA TION A-2 A-2 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC TECHNICAL SPECIFICA TIONS - SAE-400 SEVERE DUTY - Make/Model Description Speed (RPM) Displacement Starting Capacities System Pe ...

  • Lincoln Electric SVM187-A - page 11

    INST ALLA TION A-3 A-3 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC Read this entire installation section before you start installation. SAFETY PRECAUTIONS Do not attempt to use this equipment un ...

  • Lincoln Electric SVM187-A - page 12

    INST ALLA TION A-4 A-4 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC HIGH AL TITUDE OPERA TION At higher altitudes, output derating may be necessary . As a rule of thumb, derate the welder output ...

  • Lincoln Electric SVM187-A - page 13

    INST ALLA TION A-5 A-5 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC BA TTER Y CONNECTION W ARNING: Use caution as the electrolyte is a strong acid that can burn skin and damage eyes. Remove and d ...

  • Lincoln Electric SVM187-A - page 14

    INST ALLA TION A-6 A-6 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDING OUTPUT CABLES With the engine off, connect the electrode and work cables to the studs provided. These connections shoul ...

  • Lincoln Electric SVM187-A - page 15

    T ABLE OF CONTENTS - OPERA TION SECTION B-1 B-1 Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY O p e r a t i o n .............................................................................. B - 1 S a f e t y I n s t r u c t i o n s ....................................................... ...

  • Lincoln Electric SVM187-A - page 16

    OPERA TION B-2 B-2 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDING SP ARKS can cause fire or explosion. • Do not weld near flammable material . • Do not weld on containers that have held ...

  • Lincoln Electric SVM187-A - page 17

    OPERA TION B-3 B-3 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC DESIGN FEA TURES AND ADV ANT AGES FOR STICK WELDING • Excellent DC constant current output for stick weld- ing applications. • ...

  • Lincoln Electric SVM187-A - page 18

    OPERA TION B-4 B-4 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC ENGINE CONTROLS IGNITION SWITCH When placed in the “ON” position, this switch ener- gizes the fuel solenoid. When placed in the ...

  • Lincoln Electric SVM187-A - page 19

    OPERA TION B-5 B-5 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDER CONTROLS POLARITY SWITCH T urn the Arc Polarity switch to electrode positive or electrode negative as required for each part ...

  • Lincoln Electric SVM187-A - page 20

    OPERA TION B-6 B-6 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC ENGINE OPERA TION For added safety always operate the welder with the doors closed. Further , leaving the doors open changes the de ...

  • Lincoln Electric SVM187-A - page 21

    OPERA TION B-7 B-7 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC TYPICAL FUEL CONSUMPTION The typical fuel consumption of the SAE-400 for various operat- ing scenarios is shown below: 1 1 199 + 1 ...

  • Lincoln Electric SVM187-A - page 22

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES B-8 B-8 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 23

    T ABLE OF CONTENTS - ACCESSORIES SECTION C-1 C-1 Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY A c c e s s o r i e s............................................................................ C - 1 O p t i o n a l F i e l d I n s t a l l e dA c c e s s o r i e s ........................ ...

  • Lincoln Electric SVM187-A - page 24

    ACCESSORIES C-2 C-2 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC OPTIONAL FIELD INST ALLED ACCESSORIES K802-D Power Plug Kit - Kit includes male plugs for 20 Amp receptacle. K2641-1 T railer - A ...

  • Lincoln Electric SVM187-A - page 25

    T ABLE OF CONTENTS - MAINTENANCE SECTION D-1 D-1 Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY M a i n t e n a n c e ........................................................................... D - 1 R o u t i n e M a i n t e n a n c e ..................................................... ...

  • Lincoln Electric SVM187-A - page 26

    MAINTENANCE D-2 D-2 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC ELECTRIC SHOCK can kill. ● Do not touch electrically live parts such as output terminals or inter- nal wiring ENGINE EXHAUST can ...

  • Lincoln Electric SVM187-A - page 27

    MAINTENANCE D-3 D-3 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC BEARING MAINTENANCE This welder is equipped with a double-shielded ball bearing having sufficient grease to last indefinitely unde ...

  • Lincoln Electric SVM187-A - page 28

    MAINTENANCE D-4 D-4 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC 1. Close the fuel shutoff valve located under the fuel tank. (on code 10856 valve is located on the fuel strainer , which is mount ...

  • Lincoln Electric SVM187-A - page 29

    MAINTENANCE D-5 D-5 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC GFCI RECEPT ACLE TESTING AND RESET- TING PROCEDURE The GFCI receptacle should be properly tested at least once every month or when ...

  • Lincoln Electric SVM187-A - page 30

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES D-6 D-6 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 31

    T ABLE OF CONTENTS-THEOR Y OF OPERA TION SECTION E-1 E-1 Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E-1 Engine Starting and Prot ...

  • Lincoln Electric SVM187-A - page 32

    THEOR Y OF OPERA TION E-2 E-2 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC ENGINE ST ARTING AND PROTEC- TION T urning on the run/stop switch supplies 12VDC power to idler/engine protection PC boa ...

  • Lincoln Electric SVM187-A - page 33

    THEOR Y OF OPERA TION E-3 E-3 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC AUT OMA TIC ENGINE IDLE SYSTEM The automatic idle system reduces the engine RPM when there is no electrical demand on th ...

  • Lincoln Electric SVM187-A - page 34

    THEOR Y OF OPERA TION E-4 E-4 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC EXCITER/AUXILIAR Y AL TERNA TOR OPERA TION The exciter alternator is the smaller power generator that is located at the ...

  • Lincoln Electric SVM187-A - page 35

    THEOR Y OF OPERA TION E-5 E-5 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC EXCITER/AUXILIAR Y AL TERNA TOR OPERA TION (Continued) AC Auxiliary Output: The exciter alternator is now producing suff ...

  • Lincoln Electric SVM187-A - page 36

    THEOR Y OF OPERA TION E-6 E-6 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDING GENERA T OR OPERA- TION Overview: The welding generator is coupled directly to the engine and produces the DC cu ...

  • Lincoln Electric SVM187-A - page 37

    THEOR Y OF OPERA TION E-7 E-7 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDING GENERA T OR OPERA- TION (Continued) Producing weld current: Weld current is produced in the armature windings wh ...

  • Lincoln Electric SVM187-A - page 38

    THEOR Y OF OPERA TION E-8 E-8 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDING GENERA T OR OPERA- TION (Continued) Current Control: The Current Control handle turns a rotor inside the reactor ...

  • Lincoln Electric SVM187-A - page 39

    THEOR Y OF OPERA TION E-9 E-9 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC WELDING GENERA T OR OPERA- TION (Continued) Interpole coils: Armature current from the remaining two sets of brush- es i ...

  • Lincoln Electric SVM187-A - page 40

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES E-10 E-10 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 41

    T ABLE OF CONTENTS - TROUBLESHOOTING AND REP AIR F-1 F-1 Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY T roubleshooting and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F-1 How to Use T roubleshooting Gu ...

  • Lincoln Electric SVM187-A - page 42

    TROUBLESHOOTING AND REP AIR F-2 F-2 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC This T roubleshooting Guide is provided to help you locate and repair possible machine malfunctions. Simply follow ...

  • Lincoln Electric SVM187-A - page 43

    TROUBLESHOOTING AND REP AIR F-3 F-3 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC Sometimes machine failures appear to be due to PC board failures. These problems can sometimes be traced to poor e ...

  • Lincoln Electric SVM187-A - page 44

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 45

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 46

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 47

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 48

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 49

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 50

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 51

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 52

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 53

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 54

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 55

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 56

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 57

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 58

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 59

    OUTPUT PROBLEMS Observe Safety Guidelines detailed in the beginning of this manual. PROBLEMS (SYMPTOMS) POSSIBLE AREAS OF MISADJUSTMENT(S) RECOMMENDED COURSE OF ACTION If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely , contact the Lincoln Electric Service Department for technical troubles ...

  • Lincoln Electric SVM187-A - page 60

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-20 F-20 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 61

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 62

    Idler Solenoid Spring Idler Rod Speed Control Lever Ball Joint Lock Nut Pulley Fan Blades Possible Strobe-T ach Mark Points FIGURE F .1 – ENGINE COMPONENTS (CODE 10856) ENGINE RPM ADJUSTMENT TEST (continued) TEST PROCEDURE 1. T urn the engine off 2. Open the left side door , on the engine end of the machine. W ARNING: Secure the door in the open ...

  • Lincoln Electric SVM187-A - page 63

    SOLENOID BRACKET BALL JOINT LOCK NUT IDLER ROD FIGURE F .2 – ENGINE COMPONENTS (CODE 1 1 199 & 1 14080) ENGINE RPM ADJUSTMENT TEST (continued) Strobe-T ach Method (continued) 5. The tach should read between 1780 and 1810 RPM 6. Move the idle switch to the “AUTO IDLE” position and wait for the idle solenoid to energize, and the engine RPM ...

  • Lincoln Electric SVM187-A - page 64

    ENGINE RPM ADJUSTMENT TEST (continued) ENGINE RPM ADJUSTMENT PROCEDURE High Idle Adjustment: IMPORT ANT : The high idle RPM is set by the engine manufacturer , and should not be changed. If the high idle RPM is not within the specified range, the engine should be serviced by a qualified engine technician. Low idle adjustment: Code 10856 only: 1. Ho ...

  • Lincoln Electric SVM187-A - page 65

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 66

    EXC I TER COVER F I VE SCREWS (TWO ON OTHER S I DE) FIGURE F .3 – EXCITER COVER SCREW LOCA TIONS BRUSH AND SLIP RING SER VICE PROCEDURE (Exciter / Auxiliary Power Alternator) (continued) PROCEDURE 1. Open either , or both of the doors on the control panel end of the SAE-400 machine. W ARNING: Secure the doors in the open position using the door r ...

  • Lincoln Electric SVM187-A - page 67

    BRUSHES FIGURE F .4 – BRUSH LOCA TIONS BRUSH AND SLIP RING SER VICE PROCEDURE (Exciter / Auxiliary Power Alternator) (continued) PROCEDURE (continued 5. Check for evidence of sticking brushes. Sticking brushes will normally result in the slip rings being pitted and discolored from excessive arcing. Another sign of sticking brushes is instability ...

  • Lincoln Electric SVM187-A - page 68

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-28 F-28 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 69

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 70

    EXC I TER COVER F I VE SCREWS (TWO ON OTHER S I DE) FIGURE F .6 – EXCITER COVER SCREW LOCA TIONS EXCITER ROT OR VOL T AGE TEST(continued) PROCEDURE 1. T urn engine off. 2. Make sure that the battery is fully charged and in good condition, and the battery connections are clean and tight. The Engine and generator should be at normal operat- ing tem ...

  • Lincoln Electric SVM187-A - page 71

    POSITIVE SLIP RING NEGA TIVE SLIP RING BRUSH HOLDER ASSEMBL Y BRUSHES VOL TMETER LEADS FIGURE F .7 – EXCITER ROTOR VOL T AGE TEST EXCITER ROT OR VOL T AGE TEST (continued) PROCEDURE (continued) 5. Connect the volt meter probes to the brush termi- nals. See the wiring diagram and Figure F .7 NOTE: On this machine, and all other Lincoln Electric DC ...

  • Lincoln Electric SVM187-A - page 72

    EXCITER ROT OR VOL T AGE TEST (continued) PROCEDURE (continued) 9. Set the RUN/ST OP switch to “ST OP” If the meter reading is normal, this test is complete. If the voltage measures zero or very near zero, the rotor may be shorting or grounding while spinning. Perform the Exciter Rotor Resistance and Ground T est . If voltage is higher than spe ...

  • Lincoln Electric SVM187-A - page 73

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 74

    EXC I TER COVER F I VE SCREWS (TWO ON OTHER S I DE) FIGURE F .8 – EXCITER COVER SCREW LOCA TIONS EXCITER ROT OR RESIST ANCE AND GROUND TEST (Exciter / Auxiliary Power Alternator) (continued) PROCEDURE “Static” T ests: 1. T urn the engine off. 2. Open either , or both of the doors on the control panel end of the SAE-400 machine. W ARNING: Secu ...

  • Lincoln Electric SVM187-A - page 75

    POSITIVE SLIP RING NEGA TIVE SLIP RING BRUSH HOLDER ASSEMBL Y OHMMETER LEADS BRUSHES FIGURE F .9 – SLIP RING LOCA TIONS EXCITER ROT OR RESIST ANCE AND GROUND TEST (Exciter / Auxiliary Power Alternator) (continued) PROCEDURE (continued) 5. Using the ohmmeter , check the rotor winding resis- tance across the slip rings. Normal resistance is approxi ...

  • Lincoln Electric SVM187-A - page 76

    POSITIVE SLIP RING NEGA TIVE SLIP RING BRUSH HOLDER ASSEMBL Y BRUSHES VOL TMETER LEADS FIGURE F .10 – SLIP RING LOCA TIONS EXCITER ROT OR RESIST ANCE AND GROUND TEST (Exciter / Auxiliary Power Alternator) (continued) PROCEDURE (continued) “Dynamic” T ests: (Also referred to as flying resistance test) This test checks for faults in the rotor w ...

  • Lincoln Electric SVM187-A - page 77

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 78

    EXC I TER COVER F I VE SCREWS (TWO ON OTHER S I DE) FIGURE F .1 1 – EXCITER COVER SCREW LOCA TIONS FLASHING VOL T AGE TEST (Engine not running) (continued) PROCEDURE 1. Open either , or both of the doors on the control panel end of the SAE-400 machine. W ARNING: Secure the doors in the open position using the door restraint system. If the machine ...

  • Lincoln Electric SVM187-A - page 79

    J1-1 (+) BA TTERY VOL T AGE J1-10, FLASHING AND HOUR METER OUTPUT J1-5, CHASSIS GROUND FIGURE F .13 – IDLER/ENGINE PROTECTION PC BOARD CODES 10856 FLASHING VOL T AGE TEST (Engine not running) (continued) PROCEDURE (continued) 7. If this voltage reading is correct, the test is com- plete. If the voltage is significantly higher than expected: There ...

  • Lincoln Electric SVM187-A - page 80

    J31-1, (+) BA TTERY VOL T AGE I NPUT J31-10, FLASH I NG AND HOUR METER OUTPUT B-1 CHASS I S GROUND FIGURE F .14 – IDLER/ENGINE PROTECTION PC BOARD CODES 1 1 199 AND 1 1408 FLASHING VOL T AGE TEST (Engine not running (continued) PROCEDURE (continued) 10. Connect positive voltmeter probe to the Idler / Engine protection PC board J1 pin 10 for Code ...

  • Lincoln Electric SVM187-A - page 81

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 82

    EXCITER ST A TOR SHORT CIRCUIT & GROUND TEST (continued) PROCEDURE 1. Open either , or both of the doors on the control panel end of the SAE-400 machine. W ARNING: Secure the doors in the open position using the door restraint system. If the machine does not have a door restraint system, remove the doors or securely restrain them to prevent the ...

  • Lincoln Electric SVM187-A - page 83

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 84

    GENERA TOR COVER FOUR SCREWS T OT AL FIGURE F .15 – GENERA TOR COVER SCREW LOCA TIONS WELDING GENERA T OR BRUSH AND COMMUT A T OR INSPECTION AND SER VICE (continued) PROCEDURE 1. Shut off the engine. 2. Open either , or both of the doors on the control panel end of the SAE-400 machine. W ARNING: Secure the doors in the open position using the doo ...

  • Lincoln Electric SVM187-A - page 85

    ARMA TURE COMMUT A TOR SPRINGS BRUSH HOLDER PLA TE BRUSHES BRUSH RET AINER BRUSH HOLDER INSULA TORS MOUNTING SCREW DRILL MARK ROCKER FIGURE F .16 – GENERA TOR COMPONENTS WELDING GENERA T OR BRUSH AND COMMUT A T OR INSPECTION AND SER VICE (continued) PROCEDURE 5. Examine the Commutator . Normal appearance: The commutator should appear smooth, and ...

  • Lincoln Electric SVM187-A - page 86

    WELDING GENERA T OR BRUSH AND COMMUT A T OR INSPECTION AND SER VICE (continued) PROCEDURE (continued) Pitted and Arc Damaged Commutator: If pitting and arc damage to the commutator is evident, the machine may have been used with badly worn brushes. The brush spring tension may have been too low , or the brushes may have been sticking in the hold- e ...

  • Lincoln Electric SVM187-A - page 87

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 88

    WELD CIRCUIT GROUND AND SHORT CIRCUIT TEST (continued) PROCEDURE 1. T urn the engine off. Weld circuit ground test: 1. Rotate the output control to the minimum output position. 2. Measure the resistance between either of the two weld output terminals and a clean chassis ground connection. 3. The resistance measurement should be very high 500,000 (5 ...

  • Lincoln Electric SVM187-A - page 89

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 90

    SHUNT FIELD COIL RESIST ANCE AND GROUND TEST (continued) PROCEDURE 1. T urn the engine off. 2 . Open both of the doors on the control panel end of the SAE-400 machine. The roof may also need to be removed on some models. W ARNING: Secure the doors in the open position using the door restraint system. If the machine does not have a door restraint sy ...

  • Lincoln Electric SVM187-A - page 91

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 92

    SHUNT FIELD CIRCUIT VOL T AGE TEST (continued) PROCEDURE 1. T urn the engine off. 2. Open both of the doors on the control panel end of the SAE-400 machine. The roof may need to be removed on some models. W ARNING: Secure the doors in the open position using the door restraint system. If the machine does not have a door restraint system, remove the ...

  • Lincoln Electric SVM187-A - page 93

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 94

    WINDING CONT ACT SPRINGS MOV ABLE CONT ACTS Min. (open) Position FIRST STEP CONT ACT POSITION ROTOR INSULA TED FILLER FIGURE F .17 – OUTPUT CONTROL UNIT DEAD SHORT , 1ST STEP , AND OPEN REACTOR TESTS (continued) PROCEDURE 1. If possible, bring the machine to normal tempera- ture by connecting a load bank and operating the machine at 100% output ( ...

  • Lincoln Electric SVM187-A - page 95

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 96

    ARMA TURE COMMUT A TOR SPRINGS BRUSH HOLDER PLA TE BRUSHES BRUSH RET AINER BRUSH HOLDER INSULA TORS MOUNTING SCREW DRILL MARK ROCKER FIGURE F .18 – ROCKER W/MARKS ROCKER ADJUSTMENT PROCEDURE (continued) PROCEDURE The factory set point drill marks: 1. When the rocker is set for the first time at the facto- ry , a 1/8” drill is used to mark the p ...

  • Lincoln Electric SVM187-A - page 97

    ROCKER ADJUSTMENT PROCEDURE (continued) PROCEDURE (continued) Initial rocker placement: 1. The rocker should be initially positioned so the center of brushes visually lines up with the center of the main poles. Lining up the four brush holder studs with the four exciter brack- et mounting bolts is acceptable for initial place- ment. The rocker shou ...

  • Lincoln Electric SVM187-A - page 98

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-58 F-58 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 99

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 100

    WINDING Contacts & Springs Output Stud Assembly Brush Holder Assembly FIGURE F .19 – BRUSH & SPRING OUTPUT CONTROL UNIT (V ARIABLE REACT OR) INSPECTION AND SERVICE PROCEDURE (continued) PROCEDURE 1. Turn the engine of f, open the doors on the control panel end of the machine and disconnect the nega- tive battery cable. The doors must be s ...

  • Lincoln Electric SVM187-A - page 101

    WINDING INSULA TED WEDGE FIGURE F .20 – BRUSH & SPRING OUTPUT CONTROL UNIT (V ARIABLE REACT OR) INSPECTION AND SERVICE PROCEDURE (continued) PROCEDURE (continued) Servicing the continuous control unit: 8. Clean the continuous output control unit by using low pressure air to remove any excess dust and dirt. If the unit is greasy or oily , a mo ...

  • Lincoln Electric SVM187-A - page 102

    Steel Shaft Coil Spring Spring Clip Flat W asher Insulator Tu b e Springs Contacts Insulator (Short Insulator T ube Not Shown) Output Stud Output Stud Bracket Brush Holder FIGURE F .21 – INSULA TOR & SPRING LOCA TIONS OUTPUT CONTROL UNIT (V ARIABLE REACT OR) INSPECTION AND SERVICE PROCEDURE (continued) PROCEDURE Servicing the rotating brush h ...

  • Lincoln Electric SVM187-A - page 103

    FIGURE F .22 – SHAFT & TUBE OUTPUT CONTROL UNIT (V ARIABLE REACT OR) INSPECTION AND SERVICE PROCEDURE (continued) PROCEDURE (continued) The shaft spring will need to be compressed and the bracket drawn close to the back of the output control before the screws can be started and tightened. Locking type pliers and a drift punch can be used to m ...

  • Lincoln Electric SVM187-A - page 104

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-64 F-64 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 105

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 106

    #237 #224 GROUND FIGURE F .23 – ENGINE AL TERNA TOR CODE 10856 ENGINE PROTECTION SYSTEM CIRCUIT TEST (continued) PROCEDURE IMPORT ANT : Before proceeding with this test, verify that the engine has normal oil pressure, is not overheated, and the alternator drive belt is in place and properly ten- sioned. Open all of the doors on the SAE-400 machin ...

  • Lincoln Electric SVM187-A - page 107

    #59 #51 FIGURE F .24 – ENGINE AL TERNA TOR CODE 1 1 199 &1 1408 ENGINE PROTECTION SYSTEM CIRCUIT TEST (continued) PROCEDURE (continued) 4. Insulate and/or position these leads so they cannot touch chassis ground, any other electrical conduc- tor , or be damaged by any moving parts. 5. Start the engine and allow it to run. 6. If the engine sti ...

  • Lincoln Electric SVM187-A - page 108

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-68 F-68 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 109

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 110

    #237 #224 GROUND FIGURE F .25 – AL TERNA TOR CODE 10856 ENGINE AL TERNA T OR TEST (continued) PROCEDURE 1. Open the right side cover , on the radiator end of the SAE-400 machine. W ARNING: Secure the door in the open position using the door restraint system. If the machine does not have a door restraint system, remove the door(s) or securely rest ...

  • Lincoln Electric SVM187-A - page 111

    #59 #51 FIGURE F .26 – AL TERNA TOR CODE 1 1 199 & 1 1408 ENGINE AL TERNA T OR TEST (continued) PROCEDURE (continued) Engine running: • Chassis ground to the B+ terminal of the alterna- tor , (Lead #237 for code 10856) (Lead #51 for codes 1 1 199 and 1 1408) the meter should read about 13.5 to 14.2 VDC. • Chassis ground to the alternator ...

  • Lincoln Electric SVM187-A - page 112

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-72 F-72 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 113

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 114

    J1-5 (-), CHASSIS GROUND J1-9 (+), 1 1 T O 13 VOL TS TO FUEL SOLENOIDS J1-1 (+), BA TTERY VOL T AGE INPUT T O PC BOARD FIGURE F .27 – PC BOARD ENGINE FUEL SYSTEM VOL T AGE TESTS (continued) PROCEDURE 1. Open the doors on the SAE-400 machine. W ARNING: Secure the doors in the open position using the door restraint system. If the machine does not h ...

  • Lincoln Electric SVM187-A - page 115

    J31-1, (+) BA TTERY VOL T AGE I NPUT J31-9 (+) OUTPUT T O FUEL SOLENO I DS AND PUMP B-1 (-) CHASS I S GROUND FIGURE F .28 – PC BOARD ENGINE FUEL SYSTEM VOL T AGE TESTS (continued) PROCEDURE For Code 10856: 1. Place the run/stop switch in the “RUN” position and within 30 seconds, check for battery voltage between terminal J1-9 (+) and terminal ...

  • Lincoln Electric SVM187-A - page 116

    ENGINE FUEL SYSTEM VOL T AGE TESTS (continued) PROCEDURE For Codes 1 1 199 and 1 1408 1. Place the run/stop switch in the “RUN” position and within 30 seconds, check for 1 1 to 13 VDC between terminal J31-9 (+) and terminal B-1 (-). 2. Check for battery voltage between terminal J31-1 (+) and terminal B-1 (-). 3. Check for positive battery volta ...

  • Lincoln Electric SVM187-A - page 117

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 118

    EXCITER ROTOR BRUSH HOLDER ASSEMBL Y NUT WA S H E R SLEEVE COLLAR BRUSH HOLDER BRACKET FIGURE F .29 – ROTOR REMOV AL AL TERNA TOR ROT OR REMOV AL AND REPLACEMENT (continued) PROCEDURE Rotor Removal 1. T urn off the engine. 2. Open either , or both of the doors on the control panel end of the SAE-400 machine. W ARNING: Secure the doors in the open ...

  • Lincoln Electric SVM187-A - page 119

    AL TERNA TOR ROT OR REMOV AL AND REPLACEMENT (continued) Rotor Replacement: 1. Clean and inspect the armature shaft, the exciter rotor and slip rings. Replace the rotor if it is dam- aged, or if the slip rings are excessively worn. 2. Carefully slide the rotor onto the armature shaft. NOTE: It is recommended that a new sleeve collar , washer and lo ...

  • Lincoln Electric SVM187-A - page 120

    Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC NOTES F-80 F-80 SAE-400 SEVERE DUTY ...

  • Lincoln Electric SVM187-A - page 121

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 122

    GENERA TOR COVER FOUR SCREWS T OT AL FIGURE F .30 – GENERA TOR COVER REMOV AL AL TERNA TOR ST A TOR REMOV AL AND REPLACEMENT (continued) PROCEDURE 1. T urn off the engine. 2. Perform the Alternator Rotor Removal Procedure. 3. Remove the roof and doors. 4. Remove the four covers protecting the welding gen- erator brushes. See Figure F .30 5. Use t ...

  • Lincoln Electric SVM187-A - page 123

    ARMA TURE COMMUT A TOR SPRINGS BRUSH HOLDER PLA TE BRUSHES BRUSH RET AINER BRUSH HOLDER INSULA TORS MOUNTING SCREW DRILL MARK ROCKER FIGURE F .31 – ROCKER & MARK LOCA TIONS AL TERNA TOR ST A TOR REMOV AL AND REPLACEMENT (continued) PROCEDURE (continued) 9. Drain the fuel and store it in an approved container . Disconnect the fuel line from th ...

  • Lincoln Electric SVM187-A - page 124

    AL TERNA TOR ST A TOR REMOV AL AND REPLACEMENT (continued) Replacing the Exciter Alternator Stator: 1. During reassembly , anti-seize compound should be applied to the screw threads. 2. Inspect the mating surfaces of the generator frame and the exciter bracket assembly . These surfaces must mate together completely so it is very impor- tant that th ...

  • Lincoln Electric SVM187-A - page 125

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 126

    GENERA T OR FRAME REMOV AL AND REPLACEMENT (continued) PROCEDURE Remove the generator frame 1. T urn off Engine. 2. Perform the Alternator Rotor Removal Procedure . 3. Perform the Alternator Stator Removal Procedure. 4. Disconnect all of the wires and cables that connect to the stator/frame assembly . Carefully mark them for reassembly . 5. Remove ...

  • Lincoln Electric SVM187-A - page 127

    Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty . For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed thr ...

  • Lincoln Electric SVM187-A - page 128

    BLOWER PADDLE/ARMATURE MOUNTING BOLTS ( 8 ) BLOWER PADDLE ROPE SLING FIGURE F .32 – SLING LIFT GENERA T OR ARMA TURE REMOV AL AND REPLACEMENT (continued) PROCEDURE Removing the Armature 1. T urn off the engine 2. Perform the Alternator Rotor Removal Procedure. 3. Perform the Alternator Stator Removal Procedure . 4. Perform the Generator Frame Rem ...

  • Lincoln Electric SVM187-A - page 129

    RETEST AFTER REP AIR F-89 F-89 SAE-400 SEVERE DUTY Return to Section T OC Return to Section T OC Return to Section T OC Return to Section T OC Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC Retest after repair The machine should be retested if any parts are replaced that could affect the machine’ s electri ...

  • Lincoln Electric SVM187-A - page 130

    T ABLE OF CONTENTS - DIAGRAM SECTION G-1 G-1 Return to Master T OC Return to Master T OC Return to Master T OC Return to Master T OC SAE-400 SEVERE DUTY Electrical Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G-1 Wiring Diagram - Control - Code 1085 ...

  • Lincoln Electric SVM187-A - page 131

    ELECTRICAL DIAGRAMS G-2 SAE-400 SEVERE DUTY ® WIRING DIAGRAM - CONTROL - CODE 10856 (M19237) M19237 EN G I N E W EL D ERS W I RI N G D I A G RA M NONE M 18827 FEI - U NLESS OT HERW I SE SPE C I F I ED T OLE RANCE MAN UFA CT UR I NG TOLE RA N CE PER E2056 ON 2 PLACE DEC I MALS I S ± .0 2 ON 3 PLA CE DE C I MA LS I S ±. 0 0 2 ON ALL AN GLES I S ± ...

  • Lincoln Electric SVM187-A - page 132

    ELECTRICAL DIAGRAMS G-3 SAE-400 SEVERE DUTY ® WIRING DIAGRAM - ENGINE - CODE 10856 (M20609) SW ITC H PR OT EC TI ON P.C. B OARD IDLER /EN G INE J1 + SW ITCH (N. C.) O IL PRESS UR E TH ERMOS TART CO LD TERM IN AL S TART B - TH ERMOS TART 5C B B + GRO UND S CR EW TO C O NTR O L P AN EL B G 223 W W R 4 3 2 5A 1 10 G 225 B 9 8 7 3 2 B SOLENO ID 226 23 ...

  • Lincoln Electric SVM187-A - page 133

    ELECTRICAL DIAGRAMS G-4 SAE-400 SEVERE DUTY ® WIRING DIAGRAM - CODE 1 1199 (M20544) AC (-) D2 238 AC 202 1 (+ ) AC 203 AC D1 A 1 2 2C R E *844 GN D-E 602B (-) NE G PO S TO R OI D 201 W 3 500 602A - 22 600A Y 4 3 1 X 4 2 P8 215 + W 2 7A 11A 11 4A 400F 6A (+ ) REA CT O R N U F 5 4 EL ECT RO D E B 600 R R 41A 214 G 602 5 6 42 4 3 41 2 1 42A 21 CB1 CB ...

  • Lincoln Electric SVM187-A - page 134

    ELECTRICAL DIAGRAMS G-5 SAE-400 SEVERE DUTY ® WIRING DIAGRAM - CODE 1 1408 (M21283) AC (-) D2 238 AC 202 1 (+ ) AC 203 AC D1 A 1 2 2CR E *844 GN D -E 602B (-) NE G PO S TOR OI D 201 W 3 500 602A - 22 600A Y 4 3 1 X 4 2 P8 215 + W 2 7A 11A 11 4A 400F 6A (+ ) REA CTO R N U F 5 4 ELE CTRO D E B 600 R R 41A 214 G 602 5 6 42 4 3 41 2 1 42A 21 201A STA ...

  • Lincoln Electric SVM187-A - page 135

    ELECTRICAL DIAGRAMS G-6 SAE-400 SEVERE DUTY ® WIRING DIAGRAM - GENERA TOR FRAME (M5570) G-6 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual. The wiring diagram specific to your code is pasted ins ide one of the enclosure panels of your machine. Return to Section TOC Return to Section TOC Re ...

  • Lincoln Electric SVM187-A - page 136

    Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ELECTRICAL DIAGRAMS G-7 SAE-400 SEVERE DUTY ® SCHEMA TIC - COMPLETE MACHINE - CODE 10856 (G5351) EN-170 S O L ID E D G E G5351 SAE-400 MAC HI N ES C HEM ATIC NONE - DO NO T SC A ...

  • Lincoln Electric SVM187-A - page 137

    ELECTRICAL DIAGRAMS G-8 SAE-400 SEVERE DUTY ® SCHEMA TIC - COMPLETE MACHINE - CODE 1 1 199 (G4924) EN-170 S O L ID E D G E G4924 SAE-400 MAC HI N ES C HEM ATIC NONE - DO NO T SC AL E T HIS DR A WING EQ UIP M ENT TYPE: SUBJECT: SCA L E: NA CRM38346 1 PAGE ___ OF ___ 1 E NGI N EE RI NG CO NT RO LLE D MA NU FA CT URE R: No THIS DOCUMENT CONTAINS PROP ...

  • Lincoln Electric SVM187-A - page 138

    Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ELECTRICAL DIAGRAMS G-9 SAE-400 SEVERE DUTY ® SCHEMA TIC - COMPLETE MACHINE - CODE 1 1408 (G5827) EN-170 S O L ID E D G E G5827 SAE-400 MAC HI N ES C HEM ATIC NONE - DO NO T SC ...

  • Lincoln Electric SVM187-A - page 139

    NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric. This information is pro- vided for reference only . Lincoln Electric discourages board level troub ...

  • Lincoln Electric SVM187-A - page 140

    ELECTRICAL DIAGRAMS G-1 1 SAE-400 SEVERE DUTY ® SCHEMA TIC - IDLER/ENGINE SHUTDOWN PC BOARD - CODE 10856 (L1 1006-2) G-1 1 NOTE: This diagram is for reference only . It may not be accurate for all machines covered by this manual. Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to ...

  • Lincoln Electric SVM187-A - page 141

    NOTE: Lincoln Electric assumes no responsibility for liablilities resulting from board level troubleshooting. PC Board repairs will invalidate your factory warranty . Individual Printed Circuit Board Components are not available from Lincoln Electric. This information is pro- vided for reference only . Lincoln Electric discourages board level troub ...

  • Lincoln Electric SVM187-A - page 142

    Return to Section TOC Return to Section TOC Return to Section TOC Return to Section TOC Return to Master TOC Return to Master TOC Return to Master TOC Return to Master TOC ELECTRICAL DIAGRAMS G-13 SAE-400 SEVERE DUTY ® SCHEMA TIC - IDLER/ENGINE SHUTDOWN PC BOARD (G4828-2) G-13 NOTE: This diagram is for reference only . It may not be accurate for a ...

Manufacturer Lincoln Electric Category Welder

Documents that we receive from a manufacturer of a Lincoln Electric SVM187-A can be divided into several groups. They are, among others:
- Lincoln Electric technical drawings
- SVM187-A manuals
- Lincoln Electric product data sheets
- information booklets
- or energy labels Lincoln Electric SVM187-A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lincoln Electric SVM187-A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lincoln Electric SVM187-A, service manual, brief instructions and user manuals Lincoln Electric SVM187-A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lincoln Electric SVM187-A.

Similar manuals

A complete manual for the device Lincoln Electric SVM187-A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lincoln Electric SVM187-A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lincoln Electric SVM187-A.

A complete Lincoln Electric manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lincoln Electric SVM187-A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lincoln Electric SVM187-A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lincoln Electric SVM187-A, that we can find in the current document
3. Tips how to use the basic functions of the device Lincoln Electric SVM187-A - which should help us in our first steps of using Lincoln Electric SVM187-A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lincoln Electric SVM187-A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lincoln Electric SVM187-A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lincoln Electric SVM187-A?

Use the form below

If you did not solve your problem by using a manual Lincoln Electric SVM187-A, ask a question using the form below. If a user had a similar problem with Lincoln Electric SVM187-A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)