English dropdown-ico

Manual Sony SRX-T420

76 pages 4.73 mb
Download

Go to site of 76

Summary
  • Sony SRX-T420 - page 1

    DA T A PROJECT OR SRX-T420 INST ALLA TION M ANU AL 1st Edition ...

  • Sony SRX-T420 - page 2

    SRX-T420 ! 警告 このマニュアルは，サービス専用です。 お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災， 人身事故につながることがあります。 危険をさけるため，サービストレーニングを受けた技術者のみご使用くだ? ...

  • Sony SRX-T420 - page 3

    1 SRX-T420 T able of Contents 2. Adjustment 2-1. Installation of SRX Controller ........................................ 2-2 2-1-1. Startup .................................................................... 2-2 2-1-2. Function Memory .................................................. 2-4 2-1-3. Log Function ....................................... ...

  • Sony SRX-T420 - page 4

    ...

  • Sony SRX-T420 - page 5

    3 SRX-T420 Manual Structure Purpose of this manual This manual is the installation manual of Data Projector SRX-T420. This manual is intended for use by trained system and service engineers, and de- scribes the information for installation of the unit. The DIF-188 board mounted on this unit as standard equipment is equivalent of LKRI-005. For the s ...

  • Sony SRX-T420 - page 6

    ...

  • Sony SRX-T420 - page 7

    1-1 SRX-T420 Section 1 Installation Panel (U8) Front side Rear side Panel (U7) block assembly Panel (U2) block assembly Panel (U4) block assembly (420) Panel (U3) Panel (U1) Panel (U1B) Panel (U6) Panel (U5) Panel (U4B) (420) Fig. 1-1-1 Outline The light source lamp bulb and projection lens are optionally available. Y ou can incorporate them in the ...

  • Sony SRX-T420 - page 8

    1-2 SRX-T420 Panel (U7) block assembly Lock Hooks Fig. 1-1-2 Grilles   Screws (with drop-safe) Panel (U2) block assembly Hooks Hooks Hooks Screws Fig. 1-1-3 1-1-2. Panel (U7) Block Assembly 1. Release the lock on the panel (U7) block assembly . 2. Remove the panel (U7) block assembly in the direction of the arrow with attention to the three h ...

  • Sony SRX-T420 - page 9

    1-3 SRX-T420 Panel (U3) Screws Hooks Panel (U6) Hooks Hooks Screws   Fig. 1-1-4 Fig. 1-1-5 1-1-4. Panel (U3) 1. Remove the panel (U7) block assembly . (Refer to Section 1-1-2.) 2. Remove the panel (U2) block assembly . (Refer to Section 1-1-3.) 3. Remove the three screws, then remove the panel (U3) in the direction of the arrow . 4. T o insta ...

  • Sony SRX-T420 - page 10

    1-4 SRX-T420 Panel (U5) Screws Screws Hooks Panel (U1B) Screws Fig. 1-1-6 Fig. 1-1-7 1-1-6. Panel (U5) 1. Remove the panel (U7) block assembly . (Refer to Section 1-1-2.) 2. Remove the panel (U6). (Refer to Section 1-1-5.) 3. Remove the three screws, then remove the panel (U5) in the direction of arrow . 4. T o install, reverse the removal procedur ...

  • Sony SRX-T420 - page 11

    1-5 SRX-T420 Screws Panel (U1) Screws Screws Screws Fig. 1-1-8 1-1-8. Panel (U1) 1. Remove the panel (U7) block assembly . (Refer to Section 1-1-2.) 2. Remove the panel (U2) block assembly . (Refer to Section 1-1-3.) 3. Remove the panel (U6). (Refer to Section 1-1-5.) 4. Remove the panel (U1B). (Refer to Section 1-1-7.) 5. Remove the eight screws, ...

  • Sony SRX-T420 - page 12

    1-6 SRX-T420 M8 bolts Jack Jack M8 bolts Holes Adjuster pipe assembly Adjuster pipe assembly Jack Frame n When setting the jack, pay attention to the holes on the bottom of flame. Fig. 1-2b In the case of tilt angle from 5 to 10 degrees: 1. Remove the panel (U7) block assembly . (Refer to Section 1-1-2.) 2. Remove the panel (U2) block assembly . (R ...

  • Sony SRX-T420 - page 13

    1-7 SRX-T420 Adjuster Anchor BKT Duct connection 8-inch duct Fig. 1-2c Fig. 1-3 In the case of fi xing this unit: This unit can be fi xed to the fl oor using the anchor BKT . When fi xing this unit, attach the anchor BKT to the adjust- er as shown in the illustration. Part name Anchor BKT (optionally available): 3-294-224-01 1-3. Installing the ...

  • Sony SRX-T420 - page 14

    1-8 SRX-T420 Bolts Focus cable Zoom cable POTENTIO cable Projection lens Pins Projection lens Notch Line T ighten the bolts in the order from  to  .    Lens bracket Fig. 1-4 1-4. Installing the Projection Lens 1. Attach the projection lens. 2. Align the notch of lens bracket with the line of projec- tion lens and tighten the suppl ...

  • Sony SRX-T420 - page 15

    1-9 SRX-T420 Hook Holes Convex portions Hole Hole Convex portions Lens cover Lens cover Lens cover Hook Hook Lens cover Hook Hook Hook Fig. 1-5a Fig. 1-5b 1-5. Installing the Lens Cover 1. Attach the lens cover in the direction of arrow with attention to the three hooks. n The lens covers are same parts, so they can be attached both upper and lower ...

  • Sony SRX-T420 - page 16

    1-10 SRX-T420 Adjuster Protection suit Arm cover Hood Face shield Face shield Glove Arm cover Glove Fig. 1-6a 1-6. Installing the Lamp Bulb w . Be sure to turn of f the power of this unit before installing the lump bulb. . Be sure that only the quali fi ed service personnel can install the lamp bulb. For the quali fi cation, please contact your l ...

  • Sony SRX-T420 - page 17

    1-1 1 SRX-T420 Screw Anode harness Portion A Lamp bulb Anode harness Anode side Screw Fig. 1-6b Fig. 1-6c Procedure m . Keep the serial code label af fi xed on the Operating Instructions of the lamp bulb which is required for installation. . Keep the materials such as packaging box, case, protection sheet because they are used when disposing of th ...

  • Sony SRX-T420 - page 18

    1-12 SRX-T420 Panel (U4) block assembly (420) Lock Screw (with drop-safe) Screw (with drop-safe) Cold mirror assembly Cold mirror assembly Screws (with drop-safe) Maintenance cover Panel (U4) block assembly Fig. 1-6d 3. Release the lock, then open the panel (U4) block assembly (420). 4. Loosen the screw (with drop-safe), then rotate the cold mirror ...

  • Sony SRX-T420 - page 19

    1-13 SRX-T420 Cathode terminal Hexagon socket set screw Anode terminal Bolt Fig. 1-6e 6. Remove the bolt from the anode terminal. 7. Loosen the hexagon socket set screw of the cathode terminal. 8. Remove the plastic cover from the lamp bulb. Plastic cover Lamp bulb Fig. 1-6f ...

  • Sony SRX-T420 - page 20

    1-14 SRX-T420 Protection sheet Lamp bulb Fig. 1-6g 9. Remove the protection sheet from the lamp bulb. 10. Loosen the knob, then move the anode holder in the direction of the arrow . 1 1. Insert portion A of the lamp into the cathode terminal. n When attaching the lamp bulb, be careful not to dam- age the re fl ector portion. Also, be careful not t ...

  • Sony SRX-T420 - page 21

    1-15 SRX-T420 Cathode terminal Hexagon socket set screw Anode terminal Bolt Anode holder Anode harness Knob Cathode terminal End face Surface C Lamp bulb Anode holder Lamp bulb Anode harness No clearance Adjust by bending this portion. Portion A In the case of anode harness separated lamp bulb Anode holder Lamp bulb Anode harness In the case of ano ...

  • Sony SRX-T420 - page 22

    1-16 SRX-T420 LKRI-003 B3 x 8 Finger holder (HIF) Panel (HIF-44) LKRI-003 B3 x 8 Fixed plate (HIF) 320 Handle Handle Fig. 1-7a Fig. 1-7b 1-7. Installing the Optional Board to INPUT A, INPUT B, INPUT C and INPUT D For any slots, the optional board, LKRI-003 or LKRI-005 can be installed. The installing procedure for each slot is same. n For INPUT A s ...

  • Sony SRX-T420 - page 23

    1-17 SRX-T420 INPUT B LKRI-003 PSW4 x 10 Panel cover (IF) 420 PSW4 x 10 PSW4 x 10 Panel cover (IF) 420 Blank panel Fig. 1-7c Fig. 1-7d 4. Remove the six screws, then remove the all blank panels. n Store the removed blank panel. 5. Remove the six screws, then remove the panel cover (IF) 420. When attaching the LKRI-003 to INPUT B slot 6. Insert the ...

  • Sony SRX-T420 - page 24

    1-18 SRX-T420 LKRI-005 B3 x 8 Finger holder (DIF) Panel (DIF-188) LKRI-005 B3 x 8 Fixed plate (DIF) 320 Handle Handle PSW4 x 10 PSW4 x 10 Panel cover (IF) 420 Blank panel Fig. 1-7e Fig. 1-7f Fig. 1-7g Procedure (LKRI-005) 1. Remove the two screws, then remove the panel (DIF-188) and fi nger holder (DIF). 2. Attach the fi xed plate (DIF) 320 using ...

  • Sony SRX-T420 - page 25

    1-19 SRX-T420 INPUT B LKRI-005 PSW4 x 10 Panel cover (IF) 420 Fig. 1-7h When attaching the LKRI-005 to INPUT B slot 6. Insert the LKRI-005 board into INPUT B slot, and connect it securely . 7. Attach the panel cover (IF) using the twelve screws. n Attach the blank panel to empty slot. ...

  • Sony SRX-T420 - page 26

    1-20 SRX-T420 Fig. 1-7i SRW-5000 HD DIGITAL VIDEO CASSETTE RECORDER LKRI-003 T o HD-SDI output terminal HD-SDI connecting cable (optionally available) T o IN terminal HDCAM recorder/player , etc. Connection with each equipment m . Connect each equipment with the power turned of f state. . Use the connecting cables applicable to each terminal. . Ins ...

  • Sony SRX-T420 - page 27

    1-21 SRX-T420 In case of LKRI-005 m . For INPUT A slot, LKRI-005 is installed by default. However , LKRI-003 can be installed. . When using a long cable, the image may not be displayed properly due to the signal attenuation. . When the 10 bit single mode is selected, the DVI cable applicable to Dual-link is required. 1. Connect the commercially ava ...

  • Sony SRX-T420 - page 28

    1-22 SRX-T420 1-8. Interlock T erminal Pin location Interlock terminal 1. Interlock Function The SRX-T420 interlock function is enabled by making the two pins of the interlock terminal open or short. The following two patterns can be used for the interlock function in the applicable serial. Pattern 1 Normal: Open Interlock: Short Open/short between ...

  • Sony SRX-T420 - page 29

    1-23 SRX-T420 Pattern 2 Normal: Short Interlock: Open Open/short between pin 5 and pin 6 with the pin 3 and pin 4 shorted state 1-9. Connecting and Wiring of External Device w Do not plug the power cord into the power supply when performing the following wiring operations. Signal cable wiring When connecting to external device to this unit, connect ...

  • Sony SRX-T420 - page 30

    1-24 SRX-T420 1-10. Connecting the Power Cord Use the 3-core power cord that satisfy A WG 8, 250 V rated and 40 A rated. Connect the power cord to the AC IN terminal block on the rear side of this unit, referring the following procedure. w . Connection of the main power and the electric wiring work should be done by quali fi ed electricians only . ...

  • Sony SRX-T420 - page 31

    1-25 SRX-T420 Screw Ground wire Ground terminal Pack by soldering Screws Ground terminal Cable clamp Screw Fig. 1-10c Fig. 1-10d 5. Pack by soldering the end of the ground wire. 6. Attach the ground terminal removed in step 4 to the ground wire, then fi x it with the screw . 7. Route the cable through the lower hole of the terminal block, then fi ...

  • Sony SRX-T420 - page 32

    1-26 SRX-T420 1-1 1. About the Optional Accessories The projection lamps of this projector are provided as optional accessories. Install the lamp houses to the projector according to your model. For versatile use of the projector , the optional accessories mentioned below can be used with the projec- tor . Select to use them according to your syste ...

  • Sony SRX-T420 - page 33

    1-27 SRX-T420 1-12. Projection Distance Charts The alphabetical characters in this section indicate the following measurements: W : Screen width (unit: mm) D: Screen diagonal length (unit: inch) L (min): Minimum distance between the center of lens and screen L (max): Maximum distance between the center of lens and screen H: Screen height (different ...

  • Sony SRX-T420 - page 34

    1-28 SRX-T420 The formula for calculating the projection distance from the screen diagonal length (D, unit: inch) is as follows: T ype of lens Projection distance calculation formula when inputting a 4K x 2K signal Projection distance calculation formula when inputting a 16:9 signal Projection distance calculation formula when inputting a 4:3 signa ...

  • Sony SRX-T420 - page 35

    1-29 SRX-T420 When projecting a 3840-pixel (aspect ratio 16:9) image at the maximum horizontal pictur e element Unit: mm (inches) W 4500 5000 6000 7000 8000 9000 10000 12000 14000 16000 (177 1/6) (196 6/7) (236 2/9) (275 3/5) (315) (354 1/3) (393 5/7) (472 4/9) (551 1/6) (630) L (min) 7001 7791 9373 10955 12537 141 18 15700 18863 22027 25190 (275 5 ...

  • Sony SRX-T420 - page 36

    1-30 SRX-T420 Using the LKRL-Z140 projection lens When projecting a 4096-pixel (4K x 2K) image at the maximum horizontal pictur e element Unit: mm (inches) W 4500 5000 6000 7000 8000 9000 10000 (177 1/6) (196 6/7) (236 2/9) (275 3/5) (315) (354 1/3) (393 5/7) L (min) 16937 18792 22502 26212 29922 33632 37342 (666 4/5) (739 5/6) (885 8/9) (1032) (1 ...

  • Sony SRX-T420 - page 37

    1-31 SRX-T420 When projecting a 2880-pixel (aspect ratio 4:3) image at the maximum horizontal pictur e element Unit: mm (inches) W 3500 4000 4500 5000 6000 7000 8000 (137 4/5) (157 1/2) (177 1/6) (196 6/7) (236 2/9) (275 3/5) (315) L (min) 18759 21404 24050 26695 31986 37277 42568 (738 1/2) (842 2/3) (946 5/6) (1051) (1259 1/3) (1467 3/5) (1676) L ...

  • Sony SRX-T420 - page 38

    1-32 SRX-T420 1-13. Dimensions Left Exhaust Front (Barycentric position) (Barycentric position) ...

  • Sony SRX-T420 - page 39

    1-33 SRX-T420 Signal cable (For the unit fixing) AC power cable * (Optional lens) * LKRL LIST (Barycentric position) To p (Barycentric position) Right Intake Intake (Barycentric position) Rear Exhaust Intake Exhaust Intake Bottom Intake Refer to List (Barycentric position) Panel for lamp replacing Unit: mm ...

  • Sony SRX-T420 - page 40

    ...

  • Sony SRX-T420 - page 41

    2-1 SRX-T420 Section 2 Adjustment 1. Install an SRX Controller in an adjusting personal computer . (Refer to Operating Instructions.) 5. Perform illumination range adjustment and registration adjustment. (Perform these adjustments as required.) (Refer to Section 2-5.) 6. Perform the γ adjustment and uniformity adjustment using the PJ COLOR ADJUSTM ...

  • Sony SRX-T420 - page 42

    2-2 SRX-T420 Fig. 2-1-1b Fig. 2-1-1a Ethernet cable (cross cable) (supplied) T o Ethernet connector PC Shield case assembly (1) NETWORK connector 2-1. Installation of SRX Controller This unit can be operated the adjustments and setting using the supplied SRX Controller . For about installation of SRX Controller , refer to Operating Instructions. 2- ...

  • Sony SRX-T420 - page 43

    2-3 SRX-T420 Required equipment . PC - CPU: Intel Pentium M 1.6 GHz or more, and OS-recommended - RAM capacity: 256 MB or more, 512 MB or more recommended, and OS-recommended - Communication: LAN (10BASE-T/100BASE-T) or COM (RS-232C) - Graphics mode: XGA (1024 x 768) or higher - HDD: Built-in Drive, having an empty capacity of 15 MB or more - CD-RO ...

  • Sony SRX-T420 - page 44

    2-4 SRX-T420 2-1-2. Function Memory Y ou can register the settings that have been adjusted in the control windows to FUNCTION 1 to 7. As the default setting, the settings are registered to FUNCTION 1. T o register the settings to FUNCTION 2 to 7, click one of the FUNCTION 2 to 7 radio buttons, then adjust the items in each window . Y ou can recall ...

  • Sony SRX-T420 - page 45

    2-5 SRX-T420 Fig. 2-2-1 2-2-1. Owner Information The information about this unit is set. Owner Name: T ype the name of owner . Organization: T ype the name of organization. Projector Region: T ype the region that the unit is installed. Location: T ype the installation location. Name: T ype the arbitrary name. Memo: T ype memo. ...

  • Sony SRX-T420 - page 46

    2-6 SRX-T420 Fig. 2-2-2 2-2-2. Date & Time The current time is set. T ime Zone: Select the zone that the unit is installed. Adjust clock for daylight saving changes: Place a check mark when adjusting clock for daylight saving. Date & T ime Upper box: Click the button to display the calendar , and select the date. Lower box: Click the hour o ...

  • Sony SRX-T420 - page 47

    2-7 SRX-T420 Fig. 2-2-3 2-2-3. Network The connection to the network is set. Internet Protocol (TCP/IP): Select either one of the following. . Obtain an IP address automatically (DHCP): Obtains the IP address automatically from DHCP . . Specify an IP address: Sets the speci fi ed IP address. When “Specify an IP address” is selected, perform th ...

  • Sony SRX-T420 - page 48

    2-8 SRX-T420 Fig. 2-2-4 2-2-4. Mail Report The sending of mail for the lamp bulb operating time and the maintenance information is set. Reporting T iming Lamp T imer Reminder: Set the lamp lighting-up time to send the lamp noti fi cation mail. Maintenance Reminder: Set the operating (power ON) time to send the maintenance noti fi cation mail. Re- ...

  • Sony SRX-T420 - page 49

    2-9 SRX-T420 Fig. 2-2-5 2-2-5. PC Communication The communication between this unit and PC is set. Projector Identifying: Setting of this unit Port No: T ype the UDP port number . Interval: Select the packet transmission interval. Broadcast Address: T ype the broadcast address. [>>] button: Add the address typed in Broadcast Address to the li ...

  • Sony SRX-T420 - page 50

    2-10 SRX-T420 Fig. 2-2-6 2-2-6. SNMP SNMP (Simple Network Management Protocol) is set. SNMP sysName: T ype the character string of standard MIB sysName. Contact: T ype the character string of standard MIB sysContact. Location: T ype the character string of standard MIB sysDescr . Send authentication trap: Place a check mark when accepting the sendi ...

  • Sony SRX-T420 - page 51

    2-1 1 SRX-T420 Fig. 2-2-7 2-2-7. Pro fi le The setting value of this unit is stored in PC, or the setting value stored in PC is written in this unit. Save: Place a check mark in the setting value to be stored in PC. File: Edit and select the fi le name to be stored. . [...] button: Select the fi le. [SAVE] button: Store the checked setting value ...

  • Sony SRX-T420 - page 52

    2-12 SRX-T420 2-3. Optical Axis Adjustment of Lamp Bulb Procedure 1. Be sure to click the “SER VICE” tab in the standby state. The SER VICE window is displayed. 2. Click the [SELECT] button in a “LAMP ADJUST & TIMER RESET” menu. LAMP INFORMA TION window is displayed. 3. Enter the serial code described in the Operating Instructions of a ...

  • Sony SRX-T420 - page 53

    2-13 SRX-T420 6. Click the “INST ALLA TION” tab. The INST ALLA TION window is displayed. 7. Set the lamp power to 100% in the “LAMP POWER” menu to project an image in 100% black. (No signal condition) 8. Display the LAMP INFORMA TION window in the SER VICE window . 9. Click the [START] button in a “Lamp Adjust” menu. The unit enters the ...

  • Sony SRX-T420 - page 54

    2-14 SRX-T420 12. In the same way , adjust the X-axis and Y -axis direction adjusting screws so that the value of the internal lumi- nance sensor becomes maximum. 13. Adjust “Z Axis Adjust” again using the [+] / [_] button so that the value of the internal luminance sensor becomes maximum. X-axis direction adjusting screw Y -axis direction adju ...

  • Sony SRX-T420 - page 55

    2-15 SRX-T420 2-4. Lens Adjustment (H Shift, V Shift, Zoom, and Focus) Procedure 1. Project a test pattern on the INST ALLA TION window . 2. Loosen the four bolts securing the projection lens. Insert the fl at screwdriver between the lens bracket and the lens bracket shield and move the projection lens from side to side to adjust the horizontal po ...

  • Sony SRX-T420 - page 56

    2-16 SRX-T420 n Set the V shift amount within 1/2 screen. If it exceeds 1/2 screen, the zoom is changed, the image position may not be positioned at same place. Check if the V shift amount exceeds 1/2 screen in the following procedure. When the V shift amount exceeds 1/2 screen, perform the adjustment. In the case that the V shift is lowered. How t ...

  • Sony SRX-T420 - page 57

    2-17 SRX-T420 2-5. Illumination Area Adjustment and Registration Adjustment 2-5-1. Illumination Area Adjustment If there is any deviation of illumination range when installing the unit, perform adjustment in the follow- ing procedure. n The adjustment cannot be correctly performed with the fi lter cover open because the fi lter cover switch senso ...

  • Sony SRX-T420 - page 58

    2-18 SRX-T420 5. Open the panel duct in the direction of the arrow . 6. Remove the two screws, then remove the panel duct cover (upper). 7. Remove the two screws, then remove the panel duct cover (lower). 8. Close the fi lter cover , then secure it with the screw . Fig. 2-5-1c Filter cover Panel duct cover (upper) Screws Screws Panel duct cover (l ...

  • Sony SRX-T420 - page 59

    2-19 SRX-T420 9. Set Lamp Power to 53% in the “LAMP POWER” menu on the INST ALLA TION window of SRX Con- troller immediately after the lamp is lit. 10. Project the white image on the screen using “T est Mode 1” in the “TEST P A TTERN” menu. n If it is dif fi cult to observe the left, right, top and bot- tom edges of the white image bec ...

  • Sony SRX-T420 - page 60

    2-20 SRX-T420 “COLOR SP ACE CONVERTER” menu Fig. 2-6-1 2-6. Color Space Conversion (CSC Adjustment) The color space of this unit can be corrected for each color reproduction range. n The CSC adjustment cannot be correctly performed if γ is displaced. It is recommended to perform the γ adjustment and the uniformity adjustment fi rst. (Refer t ...

  • Sony SRX-T420 - page 61

    2-21 SRX-T420 “COLOR SP ACE CONVERTER” menu Fig. 2-6-2 12. Check that the difference between the value measured in step 1 1 and the “T arget Color Gamut” value is within the following margin of error . 80% green signal when Adobe RGB is selected: within ? 0.010 Other than the above: within ? 0.005 n If the difference is not within the margi ...

  • Sony SRX-T420 - page 62

    2-22 SRX-T420   Fig. 2-7-1a 12. Check that the difference between the value measured in step 1 1 and the “T arget Color Gamut” value is within the margin of error ? 0.005. n If the difference is not within the margin of error , repeat steps 5 to 11. 13. Click the [APPLY] button. 2-7. Functions of Each Window This section describes the fun ...

  • Sony SRX-T420 - page 63

    2-23 SRX-T420 . MASKING ADJUST Adjusts the image masking according to the screen shape by the six adjusting point respectively . And adjustment value is displayed by pointing the cursor at each adjusting point. When an adjusting point is double-clicked, the adjustment window is displayed. A setting value increases when you click the [+] button. A n ...

  • Sony SRX-T420 - page 64

    2-24 SRX-T420     Fig. 2-7-2 . MUTING Operates to close and open of the douser . - [ON] button: Close the douser . (Muting condition) - [OFF] button: Open the douser . . CUT OFF When a 3D lens is attached, switch the output of L image and R image. For detail, refer to the Installation and Service Manual of LKRL-A002/A003.  POWER/Loca ...

  • Sony SRX-T420 - page 65

    2-25 SRX-T420  LENS CONTROL Adjusts the image projected on the screen. . Zoom: Adjusts the size of an image. An image is expanded when you click the [+] button. It is reduced when you click the [_] button. . Focus: Adjusts a focus. A focus is adjusted to the distance place when you click the [+] button. It is adjusted to the nearby place when yo ...

  • Sony SRX-T420 - page 66

    2-26 SRX-T420         Fig. 2-7-3a 2-7-3. SERVICE Window  WHITE BALANCE  REGISTRA TION ADJUST  LAMP ADJUST & TIMER RESET  AIR FIL TER TIMER  INTERPOLA TION  MAINTENANCE TIMER  COLOR SP ACE CONVER TER  VERSION INFORMA TION  WHITE BALANCE The adjustments of Gain R/G/B and Bias R/G/B are performed ...

  • Sony SRX-T420 - page 67

    2-27 SRX-T420  REGISTRA TION ADJUST Moves R (red), G (green), and B (blue) in the horizontal and vertical directions by two pixels (maximum) one pixel at a time so as to adjust registration. . On: Selects when adjusting. . Off: Selects when not adjusting. . H: Pixels move in the horizontal direction. R: Red pixels horizontally move by two pixels ...

  • Sony SRX-T420 - page 68

    2-28 SRX-T420  INTERPOLA TION Switches the interpolation function during the projection of 2K-resolution image. . On: Projects the high-resolution picture quality with a smooth image. . Off: Projects the pixelated rough image.  MAINTENANCE TIMER . Elapsed Timer Displays the cumulative lighting time of lamp valve. (excluding cooling time) n Ot ...

  • Sony SRX-T420 - page 69

    3-1 SRX-T420 Section 3 Error Message The following messages are displayed in the status message display at the back of the main unit and the “W arning Info” of an SRX controller . These messages are classi fi ed into ALER T (degree of risk: high), W ARNING (degree of risk: middle), and F AILURE (degree of risk: low) according to the degree of ...

  • Sony SRX-T420 - page 70

    3-2 SRX-T420 ALERT (Degree of risk: high) Message No. Error message T rouble Remedy ALERT_01 BOARD ERROR The power of IF A board is defective. Check the IF A board. Replace the IF A board if it is damaged. ALERT_02 BOARD ERROR The power of IFB board is defective. Check the IFB board. Replace the IFB board if it is damaged. ALERT_03 BOARD ERROR The ...

  • Sony SRX-T420 - page 71

    3-3 SRX-T420 Message No. Error message T rouble Remedy ALERT_33 BALLAST ERROR The power unit for lamp fan is abnormal. Check the power unit for lamp fan. Re- place the fan if it is damaged. ALERT_34 BALLAST ERROR The power unit for lamp is abnormal. Check the cable between the power unit for lamp and lamp house. Check the power unit for lamp. Repla ...

  • Sony SRX-T420 - page 72

    3-4 SRX-T420 Message No. Error message T rouble Remedy W ARN_26 DOUSER ERROR DOUSER operation is failed. Check the connector of a shift block. Check the shift block. Replace the shift block if it is damaged. W ARN_27 BALLAST ERROR A power unit for lamp communication failed. Check the cable between the power unit for lamp and lamp house. Check the p ...

  • Sony SRX-T420 - page 73

    3-5 SRX-T420 Message No. Error message T rouble Remedy F AIL_19 LENS ERROR Focus operation is failed. Check the lens and lens cable. Check the SY board. Replace the SY board if it is damaged. F AIL_21 ADJUSTMENT ERROR The Z-axis operation is failed. Check the lamp house-supplied motor and harness. Replace the motor if it is dam- aged. Check the SY ...

  • Sony SRX-T420 - page 74

    3-6 SRX-T420 n Fan location T op view 7 Front side Lamp fan A Lamp fan B Lamp fan C Lamp fan D Peltier R fan Peltier G fan Peltier B fan DST board Filter cover PBS fan PS converter fan 1 CN board PS converter fan 2 Front side ...

  • Sony SRX-T420 - page 75

    ...

  • Sony SRX-T420 - page 76

    Sony Corporation SRX-T420 (SY) E 9-968-662-01 Printed in Japan 2009. 10 22 ©2009 ...

Manufacturer Sony Category Projector

Documents that we receive from a manufacturer of a Sony SRX-T420 can be divided into several groups. They are, among others:
- Sony technical drawings
- SRX-T420 manuals
- Sony product data sheets
- information booklets
- or energy labels Sony SRX-T420
All of them are important, but the most important information from the point of view of use of the device are in the user manual Sony SRX-T420.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Sony SRX-T420, service manual, brief instructions and user manuals Sony SRX-T420. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Sony SRX-T420.

Similar manuals

A complete manual for the device Sony SRX-T420, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Sony SRX-T420 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Sony SRX-T420.

A complete Sony manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Sony SRX-T420 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Sony SRX-T420, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Sony SRX-T420, that we can find in the current document
3. Tips how to use the basic functions of the device Sony SRX-T420 - which should help us in our first steps of using Sony SRX-T420
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Sony SRX-T420
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Sony SRX-T420 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Sony SRX-T420?

Use the form below

If you did not solve your problem by using a manual Sony SRX-T420, ask a question using the form below. If a user had a similar problem with Sony SRX-T420 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)