-
Fluke 233 - page 1
233 True-rms Remote Display Digital Multimeter PN 3465366 September 2009 © 2009 Fluke Corporation. All rights rese rved. Pri nted in USA. S pecifications are subject to change without notice. All product names are trademarks of their respectiv e companies. Getting Started Manual ...
-
Fluke 233 - page 2
LIMITED WARRANTY A ND LIMITATION OF LIA BILITY This Fluke product will be free from defects in material and wo rkmanship for three years from the date of purchase. T his warranty does not cover fuses, disposable batteries, or damage from accid ent, neglect, misuse, alteration, contamination, or abnormal conditions of operation or ha nd ling. Resell ...
-
Fluke 233 - page 3
1 Introduction The Fluke 233 (hereafter the Meter) is a co mpact and easy to operate tool for electr ical and electronic circuit measurements. XW Warning Read "Safety Information " before you use the Meter. How to Contact Fluke Use one of the telephone numbers be low to speak with a Fluke representative: Technical Support USA: 1-800-44-FL ...
-
Fluke 233 - page 4
233 Getting Started Manual 2 Safety Information The Meter complies with: • ISA-82.02.01 • CAN/CSA C22.2 No. 61010-1-04 • ANSI/UL 61010-1:2004 • EN 61010-1:2001 • EN 61326-1:2006 • EN 61326-2-2:200 6 • ETSI EN 300 328 V1.7.1:2006 • ETSI EN 300 489 V1.8.1:2008 • FCC Part 15 Subpart C Sections 15.207, 15.209, 15.249 F CCID: T 68-F233 ...
-
Fluke 233 - page 5
True-rms Remote Display Digital Multimeter Safety Information 3 • Remove the test leads from th e Meter before the battery door on the Meter base is opened. • Examine the test leads for damaged insulation or exposed metal. Measure th e test leads for continuity. Replace damaged test leads befo re you use the Meter. • Do not apply more tha n t ...
-
Fluke 233 - page 6
233 Getting Started Manual 4 • Use only specified 1.5-V AA batteries (three in the Meter base and two in the display), correctly installed, for Meter power. • Comply with local and n ational safety requirements when in hazardous locations. • Only use test leads that have the same voltage, category , and amperage ratings as the Meter and that ...
-
Fluke 233 - page 7
True-rms Remote Display Digital Multimeter Safety Information 5 Table 1. Electrical Symbols B AC (Alternating Current) J Earth ground F DC (Direct Current) I Fuse X Hazardous voltage P Conforms to European Union directives. W Risk of Danger. Important information. See Manual. ) Conforms to relevant Canadian Standar ds Association directives. Ba ...
-
Fluke 233 - page 8
233 Getting Started Manual 6 Features See Tables 3 through 4 for a list of Meter features with a short feature descriptio n. Table 2. Display meter remote Auto RangeManual Range 1 2 3 4 5 6 8 9 11 13 12 14 10 7 gcc101.eps No. Symbol Indication 1 MIN MAX AVG mode on. 2 MAX MIN AVG Maximum, minimum, or average measurement shown. 3 Display hol ...
-
Fluke 233 - page 9
True-rms Remote Display Digital Multimeter Features 7 Table 2. Display (cont.) No. Symbol Indication 4 Radio connection indicat or. 5 ° C, ° F degr ees Celsius, degrees Fah renheit 6 A amperes (amps) V, mV volts, millivolts μ F, nF microfarad, nanofarad DC AC Direct current or alternating current. Ω , M Ω , k Ω ohm, megohm, kilohm Hz, kHz ...
-
Fluke 233 - page 10
233 Getting Started Manual 8 Table 3. Input s 1 2 3 gcc110.eps No. Terminal Description 1 A Input for 0 A to 10.00 A current measurements. 2 COM Common terminal for all measurements. 3 Input for voltage, continuity, resistance, di ode, capacitance, tem perature, and frequenc y measurements. ...
-
Fluke 233 - page 11
True-rms Remote Display Digital Multimeter Features 9 Table 4. Funct ion Switch P ositions Sw it ch Position Description Hz (button) AC voltage from 0.06 to 1000 V. Frequency from 5 Hz to 50 kHz. DC voltage from 0.001 V to 1000 V. AC voltage from 6.0 to 600.0 mV, dc-c oupled. DC voltage from 0.1 to 600. 0 mV. Ohms from 0.1 Ω to 40 M Ω ...
-
Fluke 233 - page 12
233 Getting Started Manual 10 Error Messages Table 5 contains possible error messages and the steps to clear the error. Table 5. Error Messages Error Messages Display-module batteries mu st be repl aced before the Meter will operate. Meter-base batteries must be replac ed before the Meter will ope ...
-
Fluke 233 - page 13
True-rms Remote Display Digital Multimeter Remote Operation 11 Remote Operation 2 1 gcc114.eps Figure 1. Display Module Separation 2 1 gcc115.eps Figure 2. Dock Display Module with Meter Base ...
-
Fluke 233 - page 14
233 Getting Started Manual 12 Fuse Test Good fuse: 0.0 Ω to 0.5 Ω Replace fuse: OL gcc105.eps Figure 3. Fuse Test Battery Replacement 2 3 gcc111.eps Figure 4. Display-Module Battery Remova l ...
-
Fluke 233 - page 15
True-rms Remote Display Digital Multimeter Battery Replacement 13 2 1 3 4 gcc112.eps Figure 5. Meter Base Batter y Replacement ...
-
Fluke 233 - page 16
233 Getting Started Manual 14 General Specifications Maximum voltage betw een any terminal and earth groun d ........................................... 1000 V rms W Fuse for A inputs ..................................................... 11 A, 1000 V 17000A interrupt ra ting Fuse Altitude Operating .................................................. ...
Do you have a question concerning Fluke 233?
Use the form below
If you did not solve your problem by using a manual Fluke 233, ask a question using the form below. If a user had a similar problem with Fluke 233 it is likely that he will want to share the way to solve it.