-
Avaya P332MF - page 1
Avaya User’s Gui de A VAYA P332MF S TACKAB LE S WITCH S O F T W ARE V E R S I O N 3.12 May 2002 ...
-
Avaya P332MF - page 2
...
-
Avaya P332MF - page 3
Avaya P332MF User’s Guide I Preface FCC Notice This equipment has been tested an d found to comply with the li mits for a Class A digital device, pursu ant to part 15 of th e FCC Rul es. These limits are design ed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This eq uipm ...
-
Avaya P332MF - page 4
II Avaya P332MF User’s Guide Notes, Cau tions an d Warnin gs Note: Notes contai n hel pful informa tio n or h ints or re fere nce to mate rial i n othe r docum entatio n. Caut ion: You should take care. Yo u coul d do somethi ng th at may damage equipment or result in lo ss of data. Wa r ni n g : Th is m eans danger. Fa ilure to follow the instru ...
-
Avaya P332MF - page 5
Avaya P332MF User’s Guide i Table of Cont ents Preface ..................... ................. ............ ........... ................. ........... ........... .............. I FCC Notice .............. ............ ..... ............ ..... ...... ........... ...... ........... ...... ..... ............ .. I Conventions Used in the Documentatio ...
-
Avaya P332MF - page 6
Table of Contents ii Avaya P332MF User’s Guide Positioning .......................... ............ ........... ................. ........... ................. ........... 19 Rack Mounting ........................ ........... ............ ................. ........... ........... ........... 20 Connecting Stacked Switches ................. ....... ...
-
Avaya P332MF - page 7
Table of Contents Avaya P332MF User’s Guide iii show time .......... ........... ................. ............ ........... ................. ........... ...... 45 show timezone .................. ........... ................. ............ ........... ................. 45 show time parameters ................. ................. ............ ..... ...
-
Avaya P332MF - page 8
Table of Contents iv Avaya P332MF User’s Guide show rmon event ......... ................. ........... ............ ................. ........... ...... 72 show ppp session ......................... ........... ................. ............ ........... ...... 72 show ppp authentication .................. ........... ................. ........... ...
-
Avaya P332MF - page 9
Table of Contents Avaya P332MF User’s Guide v set snmp trap ..................... ........... ................. ............ ........... ................. 94 set snmp trap auth ............ ................. ........... ............ ................ ............ 95 set snmp retries ...... ........... ................. ........... ............ ... ...
-
Avaya P332MF - page 10
Table of Contents vi Avaya P332MF User’s Guide set autopartition ................ ........... ................. ........... ................. .......... 116 set license ........... ................. ........... ........... ................. ............ ...............116 set ppp authentication incoming ..... ........... ................. ....... ...
-
Avaya P332MF - page 11
Table of Contents Avaya P332MF User’s Guide vii no username ................ ............ ................. ........... ........... ................. .... 135 show username ................. ........... ................. ............ ................ .......... 136 set ppp chap-secret ................. ................. ........... ........... .. ...
-
Avaya P332MF - page 12
Table of Contents viii Avaya P332MF User’s Guide Avaya Approved GBIC Trans ceivers ........ ................. .......... 152 Specifications ............... ............ ................. ........... ................. .... 1 52 Agency Approval ............. ................. ........... ............ ............... 153 MTBF ................. ..... ...
-
Avaya P332MF - page 13
Avaya P332MF User’s Guide ix List of Figur es Figure 2.1 Avaya P3 33T and Avay a P3 34T st ac ks wit h a n Avay a P882 Backbone ............ ............ ........... ................. ........... ............ ................ ............ .. 5 Figure 2.2 Avaya P33 0 stacks with an Avaya 330 ba ckbone ............ ........ 6 Figure 2.3 Avaya P33 2 ...
-
Avaya P332MF - page 14
List of Figures x Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 15
Avaya P332MF User’s Guide xi List of Tables Table 3.1 Avaya P332MF LED De scriptions ............... ........... ........... ........ 9 Table 3.2 Avaya P330 <- -> Select buttons ....... ................. ........... ............ 10 Table 4.1 Default Switch Settings ..................... ............ ................ ............ 26 Table 4. ...
-
Avaya P332MF - page 16
List of Tables xii Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 17
Avaya P332MF User’s Guide 1 Chapter 1 Avaya P330 Overview The Avaya P330 family of stackable Ethernet workgroup switches includes a ra nge of modul es with 10 /100/100 0 Mbps port s and a Lay er 3 capabili ty/ATM Expan sion Module. Th e Avaya P332MF sw itch ha s 12x100B aseFX MT-RJ port s and an Expansion M odule slot. The optiona l expansion mo ...
-
Avaya P332MF - page 18
Chapt e r 1 Avaya P3 30 Overvi e w 2 Avaya P332MF User’s Guide Avaya P330 Standards Suppo rted The Avaya P3 3 0 complies with th e following sta nda rds. IEEE • 802.3x Flow Control on all ports • 802 .1Q VLAN Tagg ing support on all por ts and 802. 1p compati ble • 802.1D Bridges and STA • 803 .2z Giga bit Ethernet ports • 803.2u Ethern ...
-
Avaya P332MF - page 19
Chapt e r 1 Avaya P3 30 Overvi e w Avaya P332MF User’s Guide 3 Avaya Mu lti-Serv ice Network Manage r™ When yo u ne ed extra con trol and m onitoring or wish to ma nage othe r Cajun Campus equipment, then the Avaya Multi-Service Network Manager network management suite is the answer. This suite provides the ease-of-use an d features necessary f ...
-
Avaya P332MF - page 20
Chapt e r 1 Avaya P3 30 Overvi e w 4 Avaya P332MF User’s Guide SMON The Avaya P3 3 0 supports Avaya’s g round-breaking SMO N Switched Networ k Moni tor ing, wh ic h the IETF ha s now ad op ted as a s tandard ( RFC261 3). SMO N provides an unprecedented top-down monito ring of switched network traffic at the following levels : • Enterprise Mon ...
-
Avaya P332MF - page 21
Avaya P332MF User’s Guide 5 Chapter 2 Applications The following sectio ns describe typical appl icat ions fo r the Avay a P330 in a networ k with other Cajun Campus products. Application 1 This applica tion shows Avay a P88 2 as the network backbone with Avaya P333T and Avay a P334T s tack s as cl os et de v ices with LAG and re dund ant lin ks. ...
-
Avaya P332MF - page 22
Chapter 2 A pplications 6 Avaya P332MF User’s Guide Application 2 This applica t io n sh ow s an Avaya P330 stack formin g t he backbone of a Smal l / Medium-s ized Enterprise (SME) network wi th Avaya P 330 stack s as clos et devices with LAN an d redun dant links. Figur e 2.2 A vaya P330 s tacks with a n A vaya 330 backbo ne Avaya P330 10/100 M ...
-
Avaya P332MF - page 23
Chap ter 2 Appl icatio ns Avaya P332MF User’s Guide 7 Application 3 This a pplicati on show s Avaya P880 as the ne twork ba ckbone with Avay a P332MF deploy ed as a dist ributio n switch. An Avaya P3 33R mult ilayer switch pr ovides loca l IP routin g. The Avay a P333T sta cks act as cl oset devices w ith LAG and redu ndant links. Figur e 2.3 Ava ...
-
Avaya P332MF - page 24
Avaya P332MF User’s Guide 8 Chapter 3 Avaya P332MF Front and Back Panels Avaya P33 2MF Front Panel The Avaya P332MF front panel contai ns LEDs , controls , connect ors and an expansion Module slot, as well as a console connector. The status LEDs and control buttons prov id e at-a-glance in formation. The front panel LED s consist of P ort LEDs an ...
-
Avaya P332MF - page 25
Chapt er 3 Avay a P3 32MF Fr o nt and Bac k Panel s Avaya P332MF User’s Guide 9 Figur e 3.2 Avaya P332 MF LEDs Note: All LEDs are lit during a reset. Table 3 .1 Avaya P332MF LED Descript ions LED Name Description LED Status PWR Power st atus OFF – power is off ON – p ower is o n Blink – usin g BUPS onl y OPR CPU o p e ration OFF – Module ...
-
Avaya P332MF - page 26
Chapt er 3 Avay a P332MF Fr ont an d B ack Pane ls 10 Avaya P332MF User’s Guide COL Collision OFF – No coll ision or FDX port ON – Col lision occurred on line Tx Transmit to lin e OFF – No transm it a ctivity ON – Data transm itted on line from the module Rx Receive from line OF F – No receive activity ON – Data received from the lin ...
-
Avaya P332MF - page 27
Chapt er 3 Avay a P3 32MF Fr o nt and Bac k Panel s Avaya P332MF User’s Guide 11 Note: To perform “Fo r ce Initia l Versi on” reset the module and at the same time press the FIV reset button (use an opened paper clip or other pointed object). Release the reset buttons first and 1 or 2 seconds later, release the FIV button. Note: The Port LEDs ...
-
Avaya P332MF - page 28
Chapt er 3 Avay a P332MF Fr ont an d B ack Pane ls 12 Avaya P332MF User’s Guide Avaya P330 Back Panel The Avaya P330 back pan el con tai ns a stacki ng su b-m od ule slo t, pow er suppl y an d BUPS connector. Figure 3.3 show s the back panel of the AC switch (top) and the DC switch (bott om) with a stac kin g sub-modu le inst alled. Figur e 3.3 A ...
-
Avaya P332MF - page 29
Chapt er 3 Avay a P3 32MF Fr o nt and Bac k Panel s Avaya P332MF User’s Guide 13 ...
-
Avaya P332MF - page 30
Chapt er 3 Avay a P332MF Fr ont an d B ack Pane ls 14 Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 31
Chapt er 3 Avay a P3 32MF Fr o nt and Bac k Panel s Avaya P332MF User’s Guide 15 ...
-
Avaya P332MF - page 32
Chapt er 3 Avay a P332MF Fr ont an d B ack Pane ls 16 Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 33
Chapt er 3 Avay a P3 32MF Fr o nt and Bac k Panel s Avaya P332MF User’s Guide 17 ...
-
Avaya P332MF - page 34
Chapt er 3 Avay a P332MF Fr ont an d B ack Pane ls 18 Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 35
Avaya P332MF User’s Guide 19 Chapter 4 Installation and Se tup The Avaya P332 MF i s read y t o work aft er yo u ca rry out the installation in structions given below. All the Avaya P332MF ports provide complete connectivity and no configuration is req uired to m ake the system work. Installing the X330STK Sta cking Sub-module in the P330 Caution ...
-
Avaya P332MF - page 36
Chapt e r 4 Insta llati on and Se tup 20 Avaya P332MF User’s Guide Note: Use Octaplane cables to in terconnect with other sw itches. Rack Mounting The Avaya P 330 case fi ts in mos t stand ard 19-inc h racks. Avaya P330 i s 2U (88m m, 3.5”) hi gh. Place the Avaya P330 in the rack a s follows: 1 Snap open the hinged ends of the front panel to re ...
-
Avaya P332MF - page 37
Chapter 4 Install ation an d Setup Avaya P332MF User’s Guide 21 Connecting Stacked Switches Note: The two ends of the Octaplane cable terminate with different connectors. Each connector can only be connected to its m atching port. The following cables are used to connect stacked sw itches: • Short Octaplane cable (X330SC) – ivory-colored, use ...
-
Avaya P332MF - page 38
Chapt e r 4 Insta llati on and Se tup 22 Avaya P332MF User’s Guide Note: You can build a stack of up to 10 Avaya P3 30 switches. If you d o not wish to stack all the sw itches in a single rack, use long Octaplane cables to connect two physical stac ks a s shown in Figu re 4.3. Figure 4.2 Incorr ect Stack Connection Power Supply Connect or BUPS Co ...
-
Avaya P332MF - page 39
Chapter 4 Install ation an d Setup Avaya P332MF User’s Guide 23 Figur e 4.3 Avaya P330 Stack Conne ction s Cable to Upper U nit Cable to Lower Unit Cable to Upper U nit Cable to Lower Unit Cable to Upper U nit Cable to Lower Unit Cable to Upper U nit Cable to Lower Unit Cable to Upper U nit Cable to Lower Unit Power Supply Connector BUPS Conn ect ...
-
Avaya P332MF - page 40
Chapt e r 4 Insta llati on and Se tup 24 Avaya P332MF User’s Guide Installing Expansion Sub-modules Caut ion: The expansion sub-modules contain components sensitive to electrostatic discharge. Do no t touch the circuit board unl ess inst ruc ted t o do so. Installing the Expansion S ub-module into the Avaya P330 1 Remove the blankin g pla te or o ...
-
Avaya P332MF - page 41
Chapter 4 Install ation an d Setup Avaya P332MF User’s Guide 25 Powering O n – Avaya P330 Module AC For the AC input version of the Avay a P 330, insert the AC power cord into the power inle t in the back of th e unit. The un it po w e r s up e v e n i f n o d i r e c t A C p o w e r i s applied to it . 1 If you are using a BUPS, inse rt a po w ...
-
Avaya P332MF - page 42
Chapt e r 4 Insta llati on and Se tup 26 Avaya P332MF User’s Guide Configuring the Switch The Avaya P 330 may b e con figured usi ng the t ext-based Comm and Line Interface (CLI), th e built-in Avaya P3 30 Device Mana ger (Embedded Web) or Ava ya Multi- Service Network Manager™ . For instruction s on the text-bas ed utility, see the CLI chapter ...
-
Avaya P332MF - page 43
Chapter 4 Install ation an d Setup Avaya P332MF User’s Guide 27 Note: Function s operate in their defaul t settin gs unless config ured oth erwise. Tabl e 4.2 De fault P ort Settings Function Default Setting 10 / 1 0 0 B a s e- T X p o rt s 100Base-F ports 1 00 0 B a s e - X p o rt s Duplex mode Full duplex Full duplex Full duplex only Port Speed ...
-
Avaya P332MF - page 44
Chapt e r 4 Insta llati on and Se tup 28 Avaya P332MF User’s Guide Cabling Avaya P3 30 modules include th e following types of p orts (a ccording to the speed and stan dard they s upport): 10Base-T, 100Ba s e-TX, 1 00Base-FX, 1000Base-S X and 1000B ase-L X. Note: To interconnect Avaya P 330 switches with tw isted pa irs, cros sed cables are req u ...
-
Avaya P332MF - page 45
Chapter 4 Install ation an d Setup Avaya P332MF User’s Guide 29 Conne cting the Co nso le Cable The Avaya P3 30 has o ne seri a l port o n th e fro nt pa nel o f the switch for connect ing a terminal, a terminal emula tor, or a modem. The serial port on the front panel is la belled “Co nsole” and ha s a R J-45 co nnector . Connect the P330 to ...
-
Avaya P332MF - page 46
Chapt e r 4 Insta llati on and Se tup 30 Avaya P332MF User’s Guide 5 Set the baud rate, ppp authentication, and ppp time out required to match your modem. These commands are described in the “Command Line Interface” chapter. 6 At the prompt, type: set interface ppp enable The CLI responds with th e following: Entering the Modem mode within 60 ...
-
Avaya P332MF - page 47
Avaya P332MF User’s Guide 31 Chapter 5 Avaya CLI – Architecture, Acce ss & Conven tions This chapt er describes the Avaya P 330 CLI arch itecture a nd convention s, and provides instructions for accessing the Avaya P330 for co nfiguration purposes. The configuration procedure involves establishing a Telnet session or a serial connecti on an ...
-
Avaya P332MF - page 48
Chapter 5 Avaya CLI – Ar ch itecture, Access & Conventions 32 Avaya P332MF User’s Guide Establishing a Telnet Connectio n Perform the followin g steps to establish a Telnet co nnection to the Avaya P330 for configuration of Stack or Ro uter parameters . You can Teln et either the Stack Master IP address or directly to one of the Router IP a ...
-
Avaya P332MF - page 49
Chapt e r 5 Avaya C LI – Ar chitecture , Ac ces s & Con ve n ti ons Avaya P332MF User’s Guide 33 Command Line Prompt When you start the CLI, the initial prompt shows the number of the Master module in the Avaya P3 30 stack. For example, if the st ack Mas ter is Mo dule 5, countin g from the bottom up, then the prom pt is: P330-5> In this ...
-
Avaya P332MF - page 50
Chapter 5 Avaya CLI – Ar ch itecture, Access & Conventions 34 Avaya P332MF User’s Guide Security Levels There are four security ac cess levels – User, Privileged, Configure and Supervisor . • The User level is a general access leve l used to show system parameter values. • The Privileged level is used by site personnel to access stack ...
-
Avaya P332MF - page 51
Chapt e r 5 Avaya C LI – Ar chitecture , Ac ces s & Con ve n ti ons Avaya P332MF User’s Guide 35 Enteri ng the CLI To enter the CLI, enter your username and password. Y our access level is indicated in the prompt as follows: The User level prompt is shown below: P330-N> The Privileged level prompt is shown below: P330-N# The Configu re l ...
-
Avaya P332MF - page 52
Chapter 5 Avaya CLI – Ar ch itecture, Access & Conventions 36 Avaya P332MF User’s Guide Navigation, Cursor Movement and Shortcuts The CLI contains a simple text editor with these functions: Getting Help On-line help may be obtain ed at any time by typing a qu estion mark ( ? ), or t he word help on the comm and line or by pressin g th e F1 ...
-
Avaya P332MF - page 53
Chapt e r 5 Avaya C LI – Ar chitecture , Ac ces s & Con ve n ti ons Avaya P332MF User’s Guide 37 Universal Commands Univers al commands are co mmands that can be issue d anywhere in the hierarchica l tree. Top and U p commands The Up command moves you up to the n ext highest level in the CLI comman d hierarchy. The Top co mmand mo ves yo u ...
-
Avaya P332MF - page 54
Chapter 5 Avaya CLI – Ar ch itecture, Access & Conventions 38 Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 55
Avaya P332MF User’s Guide 39 Chapter 6 CLI – Layer 2 This chapter provides all the Layer 2 CLI commands, parameters and their default values. The CLI is comman d-line driven and does no t have any menus. To a ctiva te a config uration o ption, yo u must type the desired co mmand at the prompt and press Enter . Note: The terms “module” and ? ...
-
Avaya P332MF - page 56
Chapt e r 6 CLI – L ay er 2 40 Avaya P332MF User’s Guide session Use t he session command to op en a sessio n with a spe cific ent ity i n a switc h o f the stack. For example, you can open a session with the Routing entity of a P332G-ML sw itch in the sta ck, or with an the X330 ATM sub -module entity plu gged in to a spe cific swi tch . The s ...
-
Avaya P332MF - page 57
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 41 clear scre en The clear screen comman d clears the current terminal display. The syntax f o r this command i s: clear screen ping Use the ping co mmand to send ICMP echo request packets to another node on the network. The syntax f o r this command i s: ping [host[number]] Note: You can us ...
-
Avaya P332MF - page 58
Chapt e r 6 CLI – L ay er 2 42 Avaya P332MF User’s Guide Show Co mmands Sum mary Tab l e Following is a table of the show commands: • show ti me Show s the current time. Pa ge 45 • show timezo ne Shows the curren t timezo ne offset. Page 45 •s h o w t i m e parameters Shows the statu s and par a meters . Page 45 • show ip route Show s t ...
-
Avaya P332MF - page 59
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 43 •s h o w p o r t s e l f - l o o p - discovery Displays which port or sw itch has an enabled IB M™ token r ing cable loop discovery sta tus. Page 57 •s h o w i n t e r n a l buffering Shows the current int ernal buffering capacity. Page 57 • show boot bank Displays the softw are b ...
-
Avaya P332MF - page 60
Chapt e r 6 CLI – L ay er 2 44 Avaya P332MF User’s Guide • show rmon event Shows the existing event entries. Page 72 • show ppp session Shows the PPP parameters of the active PPP sessio n. Page 72 • show ppp authentication Sh ows the authentica tio n method used for P PP sessions. Page 72 • show ppp incom ing timeout Show s the amount o ...
-
Avaya P332MF - page 61
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 45 show time Use the show time command to display the current stac k ti me. The syntax f o r this command i s: show time Output Ex am ple: P330-N> show time 10:32:34 27 JAN 2000 GMT show timezone Use the show timezone command to display the current stack time z one. The syntax f o r this ...
-
Avaya P332MF - page 62
Chapt e r 6 CLI – L ay er 2 46 Avaya P332MF User’s Guide show ip route Use t he show ip route command to display IP routin g tab le entries. The synt ax for this command is : show ip route Output Exam ple: P330-N> show ip route show image versio n Use the show image version co mmand to disp la y the software version of the image on both mem ...
-
Avaya P332MF - page 63
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 47 show downl oa d status Use the show download status comman d to dis play a summ ary of the last softwar e download operat ion. The syntax f o r this command i s: show download status [slot] Output Ex am ple: P330-1(super)# sh download status 1 Mod Bank Download State Activity Status Downl ...
-
Avaya P332MF - page 64
Chapt e r 6 CLI – L ay er 2 48 Avaya P332MF User’s Guide show snmp retries Use the show snmp retries comma nd to display t he number of retries initiated by the Device Manager a pplica tion when it tries to sen d SNMP messages to the devi ce . The synt ax for this command is : show snmp retries Output Exam ple: P330-N> show snmp retries the ...
-
Avaya P332MF - page 65
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 49 The syntax f o r this command i s: show logout Output Ex am ple: P330-N> show logout CLI timeout is 10 minutes show inter face Use the show interface command to display in f ormation on net work interfaces. The syntax f o r this command i s: show interface Output Ex am ple: To display ...
-
Avaya P332MF - page 66
Chapt e r 6 CLI – L ay er 2 50 Avaya P332MF User’s Guide show port Us e t he show port command to display port status. The synt ax for this command is : show port [<mod_num>[/<port_num>]] Output Exam ple: To display the sta tus for port 4 on switch 3: P330-N> show port 3/4 Port Name Status Vlan Level Neg Dup. Spd. Type ------ --- ...
-
Avaya P332MF - page 67
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 51 show port trap Use the show port trap command to display informa tio n on SNMP generic link up/down traps sent fo r a specif ic po rt. The syntax f o r this command i s: show port trap [<mod_num>[/<port_num>]] Output Ex am ple: P330-N> show port trap 1/1 Port 1/1 up/down tr ...
-
Avaya P332MF - page 68
Chapt e r 6 CLI – L ay er 2 52 Avaya P332MF User’s Guide show port classific ation Use the show port classification command to display a port’s classification. The synt ax for this command is : show port classification [module/[port] Output Exam ple: P330-1(super)# show port classification Port Port Classification ------ --------------------- ...
-
Avaya P332MF - page 69
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 53 show interm o dule port redundan cy Use the show intermodule redundancy com mand to display the intermodule redu ndancy e n try defi ned fo r the stack. The syntax f o r this command i s: show intermodule port redundancy Output Ex am ple: P330-N> show intermodule port redundancy Primar ...
-
Avaya P332MF - page 70
Chapt e r 6 CLI – L ay er 2 54 Avaya P332MF User’s Guide Output Exam ple: P330-N> show port vlan-binding-mode port 1/1 is statically bound port 1/2 is statically bound port 1/3 is statically bound port 1/4 is statically bound port 1/5 is statically bound port 1/6 is statically bound port 1/7 is statically bound port 1/8 is statically bound p ...
-
Avaya P332MF - page 71
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 55 show port blockin g Use the show port blocking command to displa y the port blocking mod e on a particular switch. Use the session command to change switches before using th is command. The show port blocking command is used with the show self-loop discovery command to confirm a port’s ...
-
Avaya P332MF - page 72
Chapt e r 6 CLI – L ay er 2 56 Avaya P332MF User’s Guide Output Exam ple: P330-N> show port blocking +-------------------+ | Port | Blk /Fwd | +-------------------+ | 1 | Blocking | | 2 | Blocking | | 3 | Blocking | | 4 | Blocking | | 5 | Blocking | | 6 | Blocking | | 7 | Blocking | | 8 | Blocking | | 9 | Blocking | | 10 | Blocking | | 11 | ...
-
Avaya P332MF - page 73
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 57 show port self-loop -discovery Use the s how port self-loop-discovery command to dis p la y which port or switch h as an enab led IBM™ t oken ring cable loop discovery sta tus. Note: This comm a nd is not supported by the P33 0-ML switches. Note: If this command is to be implemen ted on ...
-
Avaya P332MF - page 74
Chapt e r 6 CLI – L ay er 2 58 Avaya P332MF User’s Guide show boot bank Use the show boot bank comm an d to disp lay the software bank from which the switch will b oot at the next boot proce ss. This command sho uld be issued sepa rately for each switch in the stack usi ng the session command. Note: This command is not supported by the P333R an ...
-
Avaya P332MF - page 75
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 59 No Expansion Not Present P330STK 2.2 Conn-Up:Ok Conn-Down:Ok BUPS BUPS:Not Prsnt Fans:None Type:None ...
-
Avaya P332MF - page 76
Chapt e r 6 CLI – L ay er 2 60 Avaya P332MF User’s Guide Output Fields show port flo wcontrol Use the show port flowcontrol command to display per-port st atus information relat ed to flow control. The synt ax for this command is : show port flowcontrol [<mod_num>[/<port_num>]] Output Exam ple: P330-N> show port flowcontrol 3/2 P ...
-
Avaya P332MF - page 77
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 61 Output Fields Field Descr iption Port Switch and port number Send- Flow contr ol- Admin Send flo w-control admini stration. Pos sible set t ing s: • ON indicates tha t the local port is allowed to send flo w control frames to the far end. • OFF ind ica tes that the local po rt is not ...
-
Avaya P332MF - page 78
Chapt e r 6 CLI – L ay er 2 62 Avaya P332MF User’s Guide show cam Use the show cam commands to display the CAM table entries for a specific port. Note: MACs asso cia ted with LAGs appear under the LAG ID, not under the LAG port. The synt ax for this command is : show cam [mac mac-addr]/[module[/port]] Output Exam ple: P330-N> show cam 1/1 De ...
-
Avaya P332MF - page 79
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 63 show port auto-neg otiation-flo wcontro l-advert isemen t Use the s how port auto-negotiation-flowc ontrol-advertisement command to displa y th e flowcontrol adve rtisement for a Gigabit port used to perf orm au to-ne gotia tio n. The syntax f o r this command i s: show port auto-negotiat ...
-
Avaya P332MF - page 80
Chapt e r 6 CLI – L ay er 2 64 Avaya P332MF User’s Guide Output Exam ple: P330-N> show trunk 1/5 Port Mode Binding mode Native vl an Vlans allowed on trunk ------ ----- -------------- ----------- ---------------------- 1/5 off statically bound 1 1 Output Fields : show vlan Use the show vlan comma nd to d is play the VLANs co nf igured in the ...
-
Avaya P332MF - page 81
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 65 show leak y-vlan Use the show leaky-vlan command to display the lea ky VLAN status. The syntax f o r this command i s: show leaky-vlan Output Ex am ple: P330-N> show leaky-vlan Leaky VLAN mode Disable show spant ree Use the show spantree command to display span nin g-tree information. ...
-
Avaya P332MF - page 82
Chapt e r 6 CLI – L ay er 2 66 Avaya P332MF User’s Guide Output Fields : Field Desc ript ion Span ning t ree Status of whe ther Spanni ng-Tre e Protocol is e nabled or disabled Designa ted Root MAC address of the designated spanning-tree root bridge Designa ted Root Pri ority Priority of the designated root bridge Designa ted Root Co st Total p ...
-
Avaya P332MF - page 83
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 67 show autopa rtition Use the show autopartition command to display the auto matic partition. Note: Autopartiti on for the P330-ML sw itches will alwa ys have the value disabled . This comman d is used to display the autopa rtition status for the ot her P330 switches in the stack. The synta ...
-
Avaya P332MF - page 84
Chapt e r 6 CLI – L ay er 2 68 Avaya P332MF User’s Guide 00000000 0 00004242 0205 0 0 0 0 0 0 0 0 0 0 MODULE 1, MESSAGE 03: 00000000 0 00002395 0205 0 0 0 0 0 0 0 0 0 0 show module- identity Use the show module identity command to displa y the switch identity required for acquiring a license. The synt ax for this command is : show module-identi ...
-
Avaya P332MF - page 85
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 69 show system Use the show system command to display the up time, system na me, loca tion, and c ontac t perso n. The syntax f o r this command i s: show system Output Ex am ple: P330-N> show system Uptime d,h:m:s ------------------------ 0,2:40:55 System Name System Location System Cont ...
-
Avaya P332MF - page 86
Chapt e r 6 CLI – L ay er 2 70 Avaya P332MF User’s Guide RMON To ol s The following are a series of RM ON commands, however we recommend using the P330 Device Mana ger. show rmon statistics Use the show rmon statistics co mmand to show the RMON statistics counters for a certain interface n umber according to the MIB-2 interface table numbering ...
-
Avaya P332MF - page 87
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 71 show rmon hi story Use the show rmon history command to show the most recent RMON history log for a given His tory Index. The history in dex is defined usi ng the rmon history comman d on Page 126 or u sing an RMON m anage ment too l. The syntax f o r this command i s: show rmon history [ ...
-
Avaya P332MF - page 88
Chapt e r 6 CLI – L ay er 2 72 Avaya P332MF User’s Guide show rmon even t Use the show rmon event command to show the parameters of an Event entry defined by the rmon event com mand on Page 1 28 or us ing the P3 30 Device Manage r. The synt ax for this command is : show rmon event [<Event Index>] Output Exam ple: P330-N> show rmon even ...
-
Avaya P332MF - page 89
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 73 sho w ppp incom ing ti meou t Use the ppp incoming timeout command to see the amoun t of tim e in minutes that a PPP ses sio n can remain idle befo re being auto matically discon nected. The syntax f o r this command i s: show ppp incoming timeout Output Ex am ple: P330-N> show ppp inc ...
-
Avaya P332MF - page 90
Chapt e r 6 CLI – L ay er 2 74 Avaya P332MF User’s Guide show tftp downloa d/ upload status Use the show tftp download status and show tftp upload status commands to display th e status of the current TFTP config uration file copy pro c ess into/from the device. The synt ax for this command is : show tftp {download|upload} status [<mod_num&g ...
-
Avaya P332MF - page 91
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 75 show web aux- files-url Use the show web aux-files-url co mmand to di splay the URL/Directo ry from where the P330 can access the Device Management auxiliary files (for example help files). The syntax f o r this command i s: show web aux-files-url show intellig ent-multicast Use the show ...
-
Avaya P332MF - page 92
Chapt e r 6 CLI – L ay er 2 76 Avaya P332MF User’s Guide show intellig ent-multicast hardw are-support Use the show intelligent-multicast hardware-support command to display the intelligen t multicast hardwa re suppo rt configuration . The synt ax for this command is : show intelligent-multicast hardware-support Output Exam ple: P330-N> show ...
-
Avaya P332MF - page 93
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 77 show secure mac port Use the show secure mac port command to displ ay the secure MAC address es of a port from the sub-agent CLI. This command is accessed only through connection to a particul ar sw itch . Note: This comm a nd is not supported by the P33 0-ML switches. Note: If this comma ...
-
Avaya P332MF - page 94
Chapt e r 6 CLI – L ay er 2 78 Avaya P332MF User’s Guide The synt ax for this command is : show arp-aging-interval Output Exam ple: P330-N> show arp-aging-interval ARP table aging interval for gateways was set to 10 minutes. show self-loop- discovery Use the show self-lo op-d iscovery comman d to display a switch ’s IB M token ring cable d ...
-
Avaya P332MF - page 95
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 79 show allow ed manage rs table Use the show allowed mana gers table command show the list of th e twenty possible allowed ma nagers IP addresses . show allowed managers table Output Ex am ple: P330-N> show allowed managers status 1 ) 149.49.32.134 2 ) Not Used 3 ) Not Used 4 ) Not Used ...
-
Avaya P332MF - page 96
Chapt e r 6 CLI – L ay er 2 80 Avaya P332MF User’s Guide Output Exam ple: P330-N> dir M# file ver num file type file location file description -- ---- -------- ---------- ------------- ---------------- 1 Booter_Image 3.5.17 SW BootImage Nv-Ram Booter Image 1 module-config N/A Running Conf Ram Module Configuration 1 stack-config N/A Running C ...
-
Avaya P332MF - page 97
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 81 Privileged Level Commands Following is a table of the Privileged Level commands. This level in cludes all the commands from the User Level described above ( s ee the User Level Commands Secti o n for a des cr i pt io n of th e s e co mmo n c om man ds ). • no ho stn ame Retu rns the pro ...
-
Avaya P332MF - page 98
Chapt e r 6 CLI – L ay er 2 82 Avaya P332MF User’s Guide no host name Use the no hostname command to return the CLI prompt to its default. The synt ax for this command is : no hostname Note: If this command is to be implemented on a switch oth er than the stac k master, a session should be opened to the relevant sw itch. no rmon histo ry Use th ...
-
Avaya P332MF - page 99
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 83 no rmon event Use the no rmon event command to delete an existing RMON event ent ry. The syntax f o r this command i s: no rmon event <Event Index> hostname Us e the hostname command to change the Command Line Interfa ce (CLI) prompt. The current switch number always appears at the ...
-
Avaya P332MF - page 100
Chapt e r 6 CLI – L ay er 2 84 Avaya P332MF User’s Guide clear ti mezone Returns the timezone to its default, Coo rdina ted Universal Time (UTC) The synt ax for this command is : clear timezone clear ip ro ute Use th e clear ip route command to delete IP routing table entries . The synt ax for this command is : clear ip route <destination> ...
-
Avaya P332MF - page 101
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 85 clear vlan Use the clear vlan command to del ete an existing VLAN and r eturn ports from this VLAN to the default VLAN #1. When you clear a VLAN, all ports assigned to that VLAN are assigned to the defaul t VLAN #1. The syntax f o r this command i s: clear vlan <vlan-id>[ name <v ...
-
Avaya P332MF - page 102
Chapt e r 6 CLI – L ay er 2 86 Avaya P332MF User’s Guide clear po rt static-vlan Use the clear port static-vlan command to delete VL AN s statically configured on a port. The synt ax for this command is : clear port static-vlan [module/port range][vlan num] Output Exam ple: P330-1(super)# clear port static-vlan 1/10 5 VLAN 5 is unbound from por ...
-
Avaya P332MF - page 103
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 87 Output Ex am ple: P330-N# clear port mirror 1/2/1/4 this command will delete the port mirror entry - do you want to continue (Y/N)? y Mirroring packets from port 1/2 to port 1/4 is cleared clear secu re mac Use the clear secure mac command to remove a MAC address from the CAM tab le of a ...
-
Avaya P332MF - page 104
Chapt e r 6 CLI – L ay er 2 88 Avaya P332MF User’s Guide Set Co mmands Sum mary Tab le Following is a Table of the Privileged Level set commands. • set logout Sets the number of minutes before an inactive CLI sess ion automat ically logs out. Page 91 • set timezone Sets the timezone for the system . Page 92 • set time protocol Sets the ti ...
-
Avaya P332MF - page 105
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 89 • set port disa ble Admin istratively disables a port. Page 100 • set port speed Sets the speed for a 10/ 100 port. Page 101 • set port duplex Se ts the dupl ex mode of a port. Page 101 • set port name Assigns a name to a port. Page 102 • set port trap Enables/disables the SNMP ...
-
Avaya P332MF - page 106
Chapt e r 6 CLI – L ay er 2 90 Avaya P332MF User’s Guide • set port spantree cost Sets the port spantree cost. P age 110 • set port security Enables MAC security on a range of ports. Page 111 • set cascading Sets switch cascading fault-monitoring mode. Page 111 • set inband vlan Sets the management VLAN ID. Page 111 • set vlan Creates ...
-
Avaya P332MF - page 107
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 91 set logout The set logout command is used to set the number of minutes un til the system automat ically disc onn ects an idle ses sio n. The syntax f o r this command i s: set logout <timeout> Output Ex am ple: To set the number of minutes until the system disconnects an idle se ssi ...
-
Avaya P332MF - page 108
Chapt e r 6 CLI – L ay er 2 92 Avaya P332MF User’s Guide automati cally: P330-N# set logout 20 Sessions will be automatically logged out after 20 minutes of idle time. Output Exam ple: To disable the automatic dis connection o f idle sessions: P330-N# set logout 0 Sessions will not be automatically logged out. set timezone Use the set timezone ...
-
Avaya P332MF - page 109
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 93 The protocol has been set to TIME protocol set time server The set time server command is used to set the TIME server address. The syntax f o r this command i s: set time server <ip> set time clien t The set time client command is used to enable or disa ble the periodic network time ...
-
Avaya P332MF - page 110
Chapt e r 6 CLI – L ay er 2 94 Avaya P332MF User’s Guide ROUTE HOST TABLE destination gateway flags Refcnt Use Interface ------------------------------------------------------------------------ 127.0.0.1 127.0.0.1 5 2 131 lo0 10.10.10.10 192.168.1.1 7 0 0 se0 ------------------------------------------------------------------------ set snmp comm ...
-
Avaya P332MF - page 111
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 95 Output Ex am ple: To enable SNMP Conf igChange traps to a specific m anager: P330-N# set snmp trap 192.168.173.42 enable config SNMP config change traps enabled. Output Ex am ple: To enable all traps to a specific manager: P330-N# set snmp trap 192.168.173.42 enable all All SNMP traps ena ...
-
Avaya P332MF - page 112
Chapt e r 6 CLI – L ay er 2 96 Avaya P332MF User’s Guide set snmp timeout Use the set snmp timeout command to set the SNMP timeout i n seconds. This command is useful for access using the Device Manager. The synt ax for this command is : set snmp timeout <number> set system location Use the set system location command to se t the m ib2 sy ...
-
Avaya P332MF - page 113
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 97 set device-m ode Use the set device-mode co mmand to change the Basic Mode of Operation of the P332 -ML/P332G T-ML/P333 R/P333R -LB switches between Ro uter and La yer 2 modes. Note: This command i s not suppo rted by the P3 33T/P334T/P332 MF swit ches whic h do not ha ve Router mo de . T ...
-
Avaya P332MF - page 114
Chapt e r 6 CLI – L ay er 2 98 Avaya P332MF User’s Guide set interface ppp Use the set interface ppp command to c onfigure the P330 PPP interface IP par amet ers, exit mode m mod e, di scon nect the PPP session, or reset the connected modem. A PPP connection can be establi shed only after the P330 is config ured with an IP address an d net-mask ...
-
Avaya P332MF - page 115
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 99 Output Ex am ple: P330-N# set interface ppp enable Entering the Modem mode within 60 seconds... Please check that the proprietary modem cable is plugged into the console port Output Ex am ple: P330-N# set interface ppp disable Entering the Terminal mode immediately set port level Use t he ...
-
Avaya P332MF - page 116
Chapt e r 6 CLI – L ay er 2 100 Avaya P332MF User’s Guide The synt ax for this command is : set port negotiation <mod_num>/<port_num> {enable|disable} Output Exam ple: To disable au tonegotiat ion on port 1, module 4: P330-N# set port negotiation 4/1 disable Link negotiation protocol disabled on port 4/1. set port ena ble Use the se ...
-
Avaya P332MF - page 117
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 101 set port speed Use the set port speed co mmand to co nfigure th e speed of a 10/100Base-T port. If autonegotiation mode is enabled for such ports, the port's speed is determined by aut on egotiation, and a n error message is thus generated if you attempt to perform the set port spee ...
-
Avaya P332MF - page 118
Chapt e r 6 CLI – L ay er 2 102 Avaya P332MF User’s Guide set port nam e Us e t he set port name to conf ig ure a name for a port. If you do no t specify a name, the po rt name re mains empty . The synt ax for this command is : set port name <mod_num>/<port_num> [<name>] Output Exam ple: P330-N# set port name 1/2 arthur Port 1 ...
-
Avaya P332MF - page 119
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 103 Output Ex am ple: To set V LAN 850 to include port s 4 thro ugh 7 on module 3. P330-N# set port vlan 850 3/4-7 VLAN 850 modified. VLAN Mod/Ports ---- ----------------------- 850 3/4-7 set port vla n-binding -mode Use the set port vlan-binding-mode command to define the bi nding method us ...
-
Avaya P332MF - page 120
Chapt e r 6 CLI – L ay er 2 104 Avaya P332MF User’s Guide Exa mple : P330-N# set port static-vlan 1/4-6 9 set port self-lo op-discovery Admin_Statu s Use the set port self-loop-discovery Admin_Status command to enable or di sable a port ’s IBM to ken ring disc overy mode. The port’s self-loop- discovery feature is a c tiva ted only after yo ...
-
Avaya P332MF - page 121
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 105 Note: If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, e.g. "new york". Output Ex am ple: P330-1(super)# set port channel 1/1-3 on test Port 1/1 channel mode set to on Port 1/2 was added to channel Port 1/3 was added to ch ...
-
Avaya P332MF - page 122
Chapt e r 6 CLI – L ay er 2 106 Avaya P332MF User’s Guide set port red undancy on/off Use the set port redundancy co mmand to define/ delete port redundancy schemes between a Primary a n d a Secondary link . There shou ld not be any redundancy sch eme already defined o n a ny o f the links. The synt ax for this command is : set port redundan cy ...
-
Avaya P332MF - page 123
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 107 set internal b uffering The set internal buffering command allo ws yo u to set the size (e ither Maximum or Minimum) of the R eceive (Rx) buffer allocated to each port of the specified switch. Th is com mand is meaningl ess when any port of the sw itch is operating wit h flow control ON ...
-
Avaya P332MF - page 124
Chapt e r 6 CLI – L ay er 2 108 Avaya P332MF User’s Guide Output Exam ple: P330-1(super)# set boot bank bank-a Boot bank set to bank-a set inter module port redu ndancy Use the set intermodule port redundancy command to define or delete the stack’s uniq ue intermodule redund ancy scheme. The defined scheme can be cleared using the set intermo ...
-
Avaya P332MF - page 125
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 109 set port mirr or Use the set port mirror co mmand to define a port mirroring source- destinat ion pair in the st ack. The syntax f o r this command i s: set por t mir ror sourc e-port < mod_num>/ <port _num> mirror-port <mod_nu m>/<p ort_num> sampling {always |dis ...
-
Avaya P332MF - page 126
Chapt e r 6 CLI – L ay er 2 110 Avaya P332MF User’s Guide set port spantre e priority Use the set port spantree priority command to set th e priority level of a port. This value defines the priority of a po rt to be blocked in case two ports with the same co sts ca use a loop. The synt ax for this command is : set port spantree priority [module ...
-
Avaya P332MF - page 127
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 111 set port secur ity Use the set port security command to enable MAC security on a port or a range of ports at th e module level. The po rt security is acti vated on ly a fter you enable the secutity mode at the stack level us ing the set security mode command. Note: This command is not s ...
-
Avaya P332MF - page 128
Chapt e r 6 CLI – L ay er 2 112 Avaya P332MF User’s Guide The synt ax for this command is : set inband vlan <value> Output Exam ple: P330-N# set inband vlan 1 Management VLAN number set to 1 set vlan Use the set vlan command to create VLANs . The synt ax for this command is : set vlan <vlan-id> [name <vlan-name>] Output Exam p ...
-
Avaya P332MF - page 129
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 113 Output Ex am ple: P330-1(super)# set port flowcontrol all 2/20 on Port 2/20 flow control administration status set to on Field D escription receiv e C ont rols the receipt of IEEE802.3 x flow -c ontrol f rames on Gig abit por ts onl y: • ON indica tes that the local port will a c t upo ...
-
Avaya P332MF - page 130
Chapt e r 6 CLI – L ay er 2 114 Avaya P332MF User’s Guide set port auto-n egotiation-flow control-advertisement The set p ort au to-neg otiatio n-flow contro l-adver tise ment command sets the flowcontrol advertisement for a Gigabit port when performing auton egoti ati on. The synt ax for this command is : set por t auto -neg otiatio n-flow con ...
-
Avaya P332MF - page 131
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 115 set leaky-vlan Use the set leaky-vlan command to define the P330 stack’s leak y VLAN mo de. In this mode, V LAN tes t is do ne only on br oadcas t/mult icas t/unkn own fr ames, and not on unicast frames. The syntax f o r this command i s: set leaky-vlan <enable|disable> Output Ex ...
-
Avaya P332MF - page 132
Chapt e r 6 CLI – L ay er 2 116 Avaya P332MF User’s Guide Exa mple : To set the priority to 4500 0: P330-N# set spantree priority 45000 Priority enabled set autopartit ion Use the set autopartition command to enable or disable auto -partitioning o n specific switches o f the stack. Note: This command can not be executed on the P332G-ML an d P33 ...
-
Avaya P332MF - page 133
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 117 set ppp aut h entication inco ming Use the set ppp authentication incoming command to define the authenticatio n meth od us ed for a PPP server or client session. The syntax f o r this command i s: set ppp authentication incoming {pap|chap|none} Example: P330-N(super)# set ppp authentica ...
-
Avaya P332MF - page 134
Chapt e r 6 CLI – L ay er 2 118 Avaya P332MF User’s Guide set web aux-fil es-url Use the set web aux-files-url comm a nd to allow the Device Manag er to automatically locate the URL (the http://www address and path) of the Web server contai ning the D evice Mana ger hel p files an d Java p l ug- in. Note: Ensure th at the Web server is al ways ...
-
Avaya P332MF - page 135
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 119 Example: P330-N> set intelligent-multicast client-port-pruning-time 20 Done! set intellig ent-multicast route r port pruning ti me Use the set intelligent-multicast router-port-pruning time command to define aging time for ro uter ports. The syntax f o r this command i s: set intellig ...
-
Avaya P332MF - page 136
Chapt e r 6 CLI – L ay er 2 120 Avaya P332MF User’s Guide The synt ax for this command is : set secure mac <mac-address> port <mod-num>/<port-num> set security mode Use the set security mode command to enable or disable MAC security at the stack level. When enabled, the ports are s ecured based on thei r individual configurati ...
-
Avaya P332MF - page 137
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 121 Output Ex am ple: P330-N# set arp-tx-interval 15 ARP tx interval was set to 15 seconds. set self-loop- discovery Admin_Status Use the set self-loop-discovery Admin_Status c omma nd to enab le o r disable IBM token ring discovery f eature at the module level. Note: You must disable Spanni ...
-
Avaya P332MF - page 138
Chapt e r 6 CLI – L ay er 2 122 Avaya P332MF User’s Guide Note: If you wish to define a string which includes spaces, you must enclose the entire string in qu otation marks, e.g. "new york ". set allow ed managers Use the set allowed managers comman d toena b le/ disable the Allowed Managers fea ture. When this feature is enabled, on ...
-
Avaya P332MF - page 139
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 123 The syntax f o r this command i s: set psu type [AC|DC][module number] Output Ex am ple: P330-N> set psu type DC 3 Power supply type was changed to DC on module 3 sync time Us e the sync time command to synchronize the time used by all switches in a stack. The syntax f o r this comman ...
-
Avaya P332MF - page 140
Chapt e r 6 CLI – L ay er 2 124 Avaya P332MF User’s Guide reset Use th e reset command to restart the system or an indi vidual switch. If no switch number is defined or the switch number of the Master is defined, th e command resets the entire system. If the switch number is defined, the command resets the specified switch o nly . Note: You sho ...
-
Avaya P332MF - page 141
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 125 reset mg p Use th e reset mgp command to perform a softw are reset in the G700 Media Gateway P rocessor. The syntax f o r this command i s: reset mgp reset wan Use the reset wan command to perform a software reset in the X330 WAN Access Router M odule. The syntax f o r this command i s: ...
-
Avaya P332MF - page 142
Chapt e r 6 CLI – L ay er 2 126 Avaya P332MF User’s Guide The synt ax for this command is : nvram initialize [switch|all] Output Exam ple: P330-N# nvram initialize This command will force a factory default and switch-over to the master module and disconnect your telnet session. Do you want to continue (y/n) [n]? y Connection closed by foreign h ...
-
Avaya P332MF - page 143
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 127 Note: If you wish to define a name which includes spaces, you must enclose the entire name in quotation marks, e.g. "new york". rmon a larm Use the rmon alarm co mmand t o create a new RMON alarm en try. The syntax f o r this command i s: rmon alarm <Alarm Number> <var ...
-
Avaya P332MF - page 144
Chapt e r 6 CLI – L ay er 2 128 Avaya P332MF User’s Guide alarm 1026 was created successfully rmon even t Us e t he rmon event command to create an RMO N event entry . The synt ax for this command is : rmon event <Event Number> <type> description <description> owner <owner> Output Exam ple: P330-N# rmon event 1054 logAnd ...
-
Avaya P332MF - page 145
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 129 This operation may take a few minutes. .. Please refrain from any other operatio n during this time. For more information , use 'upload sta tus' command ************************************** ****************************** * If you are currently running the P33 0 Device Manager ...
-
Avaya P332MF - page 146
Chapt e r 6 CLI – L ay er 2 130 Avaya P332MF User’s Guide For more information , use 'show t ftp upload status' command ********************************** ********************************** * If you are currently running the P330 Device Manager application,* * it is recommended to exit from i t before performing configuration* * downl ...
-
Avaya P332MF - page 147
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 131 The syntax f o r this command i s: copy tftp module-config <filename> <ip> Example: P330-N# copy tftp module-config c:configswitch1.cfg 192.168.49.10 5 copy tftp EW_ arc hive Use the copy tftp EW_archive co mmand to download th e P330 Devi ce Mana ger applic ation in to the ...
-
Avaya P332MF - page 148
Chapt e r 6 CLI – L ay er 2 132 Avaya P332MF User’s Guide <mod_num> Exa mple : P330-N# copy tftp SW_image c:p330p330web101 EW_archive c:p330p330web201 192.168.49.10 5 Radius Co mm a nd s The following ra d ius co mmands are accessible fro m Pri vileged mode. image-file Commo n name for th e files that contain th e Software Image and E ...
-
Avaya P332MF - page 149
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 133 set radius aut hentica tion secret Use the set radius authentication secret command to enable secret authentication for the P 330 unit. The syntax f o r this command i s: set radius authentication secret <string> string text password Example: P330-N(super)# set radius authenticatio ...
-
Avaya P332MF - page 150
Chapt e r 6 CLI – L ay er 2 134 Avaya P332MF User’s Guide set radius au thentication r etry-time Use the set radius authentication retry-time command to set the tim e to wait before re-sen ding an access request. The synt ax for this command is : set radius authentication retry time <time> set radius au thentication r etry-numbe r Use the ...
-
Avaya P332MF - page 151
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 135 Supervisor Level Commands This level includes a ll the co mmands of th e User and Privileged Levels (inclu ding all show an d set commands). username Use t he username command to add a local user account. You can only do this from within the Supervisor Level. The syntax f o r this comman ...
-
Avaya P332MF - page 152
Chapt e r 6 CLI – L ay er 2 136 Avaya P332MF User’s Guide show user name Use the show username command to display the username. The syntax f o r this command is: show username Output Exam ple: P330-N> show username User account password access-type -------------- ------------------------------ ----------- root **** admin set ppp chap- secret ...
-
Avaya P332MF - page 153
Chapt e r 6 CLI – L ay er 2 Avaya P332MF User’s Guide 137 Example: P330-N(super)# show radius authentication RADIUS authentication parameters: --------------------------------- Mode: Enabled Primary-server: 192.168.42.252 Secondary-server: 192.168.48.134 Retry-number: 4 Retry-time: 5 UDP-port: 1645 Shared-secret: sodot set radius aut hentica ti ...
-
Avaya P332MF - page 154
Chapt e r 6 CLI – L ay er 2 138 Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 155
Avaya P332MF User’s Guide 139 Chapter 7 Installing the Embedded Web Manager The Embedded Web Ma nager provides the follow ing: • Man aging and moni toring Pow er o ver Ethe rnet. • Device Configuration - Viewing and modifying the different device configurations. • Vi rtu al LAN s - Vi ewing an d edi ting Vir t ual LAN info rmation. • Link ...
-
Avaya P332MF - page 156
Chap t er 7 I n sta ll ing th e Emb edded Web Ma nage r 140 Avaya P332MF User’s Guide • Microsoft® Internet Explorer® or Net scape Navigator/Comm un icator® (see table) Note for users of Netscape Navigator: The Ja va p lug- in requir es certa in se rvices f rom Windows 95 which ar e not presen t i f Internet Ex plore r is not installed. I n ...
-
Avaya P332MF - page 157
Chapter 7 Installin g the Em bedded Web Manager Avaya P332MF User’s Guide 141 The welcome page is di spla yed: Figur e 7.1 The Welcome Page ...
-
Avaya P332MF - page 158
Chap t er 7 I n sta ll ing th e Emb edded Web Ma nage r 142 Avaya P332MF User’s Guide — If you h ave the Java plug -in instal led, the W eb- based manager sh ould open in a ne w window (see Fi gur e 7.2). Figur e 7.2 Web-b ased Man ager —I f y o u d o not have the Java plu g-in installed, f oll ow the instructions on the W elcome page that of ...
-
Avaya P332MF - page 159
Chapter 7 Installin g the Em bedded Web Manager Avaya P332MF User’s Guide 143 Installing the Java Plug-in If the network mana ger has con figured the system, the plug-in should be installed automat ically. Note: En su r e t h at J av a o r Ja va S cr i pt is en a b le d on your W eb browser. Please refer to your browser on-line help or documentat ...
-
Avaya P332MF - page 160
Chap t er 7 I n sta ll ing th e Emb edded Web Ma nage r 144 Avaya P332MF User’s Guide Installing the On-Line Help and Java Plug -In on your Web Site Note: This p r ocedu r e is option al. Copying the help files and Java plug-in to a local Web server allows users to access the on-line help for the Em bedded Manager an d enables automatic installat ...
-
Avaya P332MF - page 161
Avaya P332MF User’s Guide 145 Appendix A Specificatio ns Avaya P332MF Sw itch Physical Power Re quirements – AC Power Re quirements – DC Laser Data Height 2U (88 mm, 3.5” ) Width 482.6 mm ( 19”) Depth 450 mm (17.7”) Weight 8 kg (17.6 lb) Input volta ge 100 t o 240 VAC, 50 /60 Hz Power d issipat ion 150 W max Input current 5.3 A Input vo ...
-
Avaya P332MF - page 162
Appendix A Specifications 146 Avaya P332MF User’s Guide Environme ntal Safety • UL for US appro ved according to UL195O Std. • C-UL(UL for Canada) approv ed according to C22.2 No.950 Std. • CE for Europe approved acco rding to EN 609 50 Std. • Laser co mponents a re “Class 1 Laser Products”: — EN-608 25/IEC-825-1 for Eur ope — FDA ...
-
Avaya P332MF - page 163
Appendix A S pecifications Avaya P332MF User’s Guide 147 • Japan - VCCI-A Immunity Approved according to: • EN5 5024 • EU - EN61 000-3-3 Other Approved according to: • CLEI Code: According to Tecordia (Bel lcore) KS- 22022 St andard • NEBS Level 3: — AC Produ ct w ith op tio nal bra cke ts — DC Product certified Interface s • 12 x ...
-
Avaya P332MF - page 164
Appendix A Specifications 148 Avaya P332MF User’s Guide • 140 ,000 hrs mi nimum (see Se ctio n MTB F in Va rious Confi gurat ions) Stacking Module Table A. 1 Stacking Module Expansion Modules Gigabit Et hernet Expansion Modules Laser Safe ty The Avaya X3 30S1/S2 multi- mode trans ceivers an d the Avaya X330L1/X3 30L2 single mod e transceivers a ...
-
Avaya P332MF - page 165
Appendix A S pecifications Avaya P332MF User’s Guide 149 Laser Classifica tion Note: Class 1 lase rs are in herently safe under reasonab ly f oreseea ble con ditions of opera tion. Caution: The use of optical instruments with this product will increase eye hazard. Usage Re strictio n The op tic al po rts of the module must be te rminated with an ...
-
Avaya P332MF - page 166
Appendix A Specifications 150 Avaya P332MF User’s Guide Fast Ethern et Fiber Expan sion Module Etherne t/Fast Ethernet Ex pansion Module Table A .3 Fib er Fast E t hernet Ex pansion Module Name Number of Port s Int erface X330F2 2 100B ase-F X Tabl e A. 4 Ethernet/ Fast Etherne t Expa n si o n Modu le Name Number of Port s Int erface X330T 16 16 ...
-
Avaya P332MF - page 167
Appendix A S pecifications Avaya P332MF User’s Guide 151 GBIC E xpansion Mo dule The Avaya X3 30G2 Expan sio n Module is th e GB IC (1.25 Gbit/s Gig abit Ethernet) Expansion M odule for the Avay a P3 30 family of sta ckable switches . Note: In order to use this module the Avaya P330 switch must must have Embedded S/W Version 2.2 or hi gher. You c ...
-
Avaya P332MF - page 168
Appendix A Specifications 152 Avaya P332MF User’s Guide Avaya Appr oved GBIC Transceiver s Caut ion: All Avaya approved GBICs are 5V. Do not insert a 3.3V G BIC. Avaya s upplies t he follow ing tw o GBIC t ransceivers for the A vaya P330 X330G2 Expansion M odul es. You can order these d irectly from your loca l A vaya representative using the PEC ...
-
Avaya P332MF - page 169
Appendix A S pecifications Avaya P332MF User’s Guide 153 Agency App ro val The transceivers comply with: • EMC Emis sion: US – F CC Part 15, Subpart B, Cl ass A; Europe – E N55022 class A • Immunit y: EN50082 -1 • Safety : UL for US UL 1950 Std., C-UL (UL for Cana da) C22.2 N o.950 St d., Food and Drug Administrat ion (FDA) 2 1 CFR 104 ...
-
Avaya P332MF - page 170
Appendix A Specifications 154 Avaya P332MF User’s Guide Removing an Ex isting E x pansio n Mo dule 1 Loos en the screws by tu rning the knobs. 2 Grasp the tw o kn obs one n e ar each side of the front p a nel, and pu ll g ently but firmly t owards yourself . 3 Insert another expansion module or the blanking plate. Note: The Avaya P330 switch must ...
-
Avaya P332MF - page 171
Appendix A S pecifications Avaya P332MF User’s Guide 155 ATM Expansi on Mod ul es There are t hree Avaya P3 30 ATM Expansion Modules: • X330-O C12F1: 500m, Multimo de fiber, can also be OC-3 reduced ra nge • X330-O C12S1: 15 km, Single -mode fiber, can also be OC-3 The ATM Mod ules ca n be installed in th e follo wing Avaya P330 Family swi tc ...
-
Avaya P332MF - page 172
Appendix A Specifications 156 Avaya P332MF User’s Guide Multi-Mode Module LED Warning The following w arnings apply to the X3 30 ATM Modules eq uipped with multi - mode fiber. Wa r ni n g : Cl ass 1 LED P r od uct. Do not view the LED through any ma gnifying device while it is powered on. Never look directly at the fiber Tx port and fiber cable e ...
-
Avaya P332MF - page 173
Appendix A S pecifications Avaya P332MF User’s Guide 157 Environmen tal Safety • UL for US a pproved according to UL195O Std. • C-UL(UL f or Canada) approved accordi ng to C22.2 No.950 Std. • CE for Europe approved acco rding to E N 60950 St d. • Overcurrent Protection: A readily access ible Listed safety-approved pro tective device with ...
-
Avaya P332MF - page 174
Appendix A Specifications 158 Avaya P332MF User’s Guide MTBF in Variou s Configurations The following table provides the MTBF for the Avaya P333T-PWR P332MFin various configurati on s. Table B.7 MTBF for the Avaya P332 MF in Various Config urat ions Model Without BUPS With BUPS Without X330S TK With X330STK Without X330STK With X330S TK P332MF 16 ...
-
Avaya P332MF - page 175
Avaya P332MF User’s Guide Index of CL I Com mand s clea r ca m 86 clea r dyn amic vl ans 85 clear log 86 clear port mirror 86 clea r port s tatic-vla n 86 clear radius authentication server 133 clea r scr een 4 1 clear secure mac 87 clea r snmp trap 84 clear timezone 84 clea r vl an 85 copy module-config tftp 129 copy stack-config tftp 128 copy t ...
-
Avaya P332MF - page 176
Index of CLI Commands 160 Avaya P332MF User’s Guide set port flowcontrol 112 set port level 99 set port mirror 109 set port name 102 set port negotiation 99 set port redundancy 106 set port redundancy on/off 106 set port security 111 set port self-loop-disc overy Admin_Status 104 set port spantree 109 set port spantree cost 110 set port spantree ...
-
Avaya P332MF - page 177
Index of CLI Commands Avaya P332MF User’s Guide show port channel 51 show port classification 52 show port flowcontrol 60 show port mirror 53 show port redundancy 52 show port security 54 show port self-loop-discovery 57 show port trap 51 show port vlan-binding-mode 53 show ppp authentication 72 show ppp baud-rate 73 show ppp configuration 73 sho ...
-
Avaya P332MF - page 178
Index of CLI Commands 162 Avaya P332MF User’s Guide ...
-
Avaya P332MF - page 179
Avaya P332MF User’s Guide 163 How to Contact Us To contact Avaya’s technical support, please call: In the United St ates Dial 1-8 00-237-0016, pres s 0, th en press 73 300. In the EM EA (Europ e, Middle East and Af rica) R egion Countr y Local Dial-In Number Coun try Local Dial-In Number Albania +31 70 414 80 01 France +33 1 4993 900 9 Austri a ...
-
Avaya P332MF - page 180
How to Con tact Us 164 Avaya P332MF User’s Guide Email: csctechnical@avaya .com Lebano n +31 70 414 8 053 Slovakia +31 70 414 8066 Lith uania +370 2 756 8 00 Slovania +31 70 414 8040 Luxembu rg +3 52 29 696 9 5624 South Af rica +08 00 995 05 9 Macedoni a +31 70 41 4 8041 Spain +34 91 375 3023 Malta +31 7 0 414 8022 Sweden +46 85 1 992 0 80 Mauri ...
-
Avaya P332MF - page 181
How t o Con tact Us Avaya P332MF User’s Guide 165 In the AP ( Asia Pac i fic) Re gion Email: sgc oe@a v ay a.co m In the CAL A (Carib be an and Latin Americ a) Regio n Email: ca ladatasu pp@avaya.com Hot Lin e:+1 720 4 449 998 Fax:+1 720 444 91 03 For updated in fo rma tion, visit ww w.avay anetwo rk.com and click "Global Support Organ izati ...
-
Avaya P332MF - page 182
How to Con tact Us 166 Avaya P332MF User’s Guide All trademarks, registered tradem arks, serv ice names, product and/ or brand name s are the sole property of their respective owners. Copyright © 2002 Avaya Inc. All rights reserved. ...
Do you have a question concerning Avaya P332MF?
Use the form below
If you did not solve your problem by using a manual Avaya P332MF, ask a question using the form below. If a user had a similar problem with Avaya P332MF it is likely that he will want to share the way to solve it.