English dropdown-ico

Manual Henny Penny OFG-391

70 pages 0.92 mb
Download

Go to site of 70

Summary
  • Henny Penny OFG-391 - page 1

    OPERA T OR’S MANUAL Henny Penny Open Fryer-Gas Model OFG-391 ...

  • Henny Penny OFG-391 - page 2

    ...

  • Henny Penny OFG-391 - page 3

    Model OFG- 391 FM05-025-F Revised 8-6-10 LIMITED W ARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT : Any part of a new appliance, except baskets, lamps, and fuses, which ...

  • Henny Penny OFG-391 - page 4

    Model OFG- 391 This manual should be retained in a convenient location for future reference. A wiring diagram for this appliance is located on the rear shroud cover of the control panel. Post in a prominent location, instructions to be followed if user smells gas. This information should be obtained by consulting the local gas supplier . Do not obs ...

  • Henny Penny OFG-391 - page 5

    Model OFG- 391 T echnical Data for CE Marked Pr oducts Nominal Heat Input: Natural (I 2H ) = 26,4 kW (90,000 Btu/h) (Net) Natural (I2E) = 26,4 kW (90,000 Btu/h) Natural (I2S) = 23,75 kW (81,000 Btu/h) Liquid Propane (I 3P ) = 27,0 kW (92,000 Btu/h) Nominal Heat Input: Natural (I 2H ) = 29,3 kW (100,000 Btu/h) (Gross) Natural (I2E) = 29,3 kW (100,00 ...

  • Henny Penny OFG-391 - page 6

    HENNY PENNY 8 HEAD GAS OPEN FR YER SPECIFICA TIONS Height 61" (155 cm) W idth 24" (61 cm) Depth 41¾" ( 107 cm) Floor Space Approximately 7 sq. ft. (.65 sq. m.) Pot Capacity 8 head of chicken (20 lbs.) (9.1 kg) 130 lbs. shortening (46 Kg.) Electrical 120 V AC, 1 Phase, 50/60 Hz, 10 Amp, 2 W ire + Ground 230 V AC, 1 Phase, 50/60 Hz, 5 ...

  • Henny Penny OFG-391 - page 7

    Model OFG- 391 T ABLE OF CONTENTS Section Page Section 1. INTRODUCTION .................................................................................................... 1- 1 1-1 Introduction .................................................................................................... 1-1 1 -2 Proper Care .................................. ...

  • Henny Penny OFG-391 - page 8

    Model OFG- 391 1-1. INTRODUCTION The Henny Penny open fryer is a basic unit of food processing equipment. This unit is used only in institutional and commercial food service operations. As of August 16, 2005, the W aste Electrical and Electronic Equip- ment directive went into effect for the European Union. Our products have been evaluated to the W ...

  • Henny Penny OFG-391 - page 9

    Model OFG- 391 1-4. SAFETY The Henny Penny open fryer has may safety features incorporated. However , the only way to ensure a safe operation is to fully under stand the proper installation, operation, andmaintenance proce dures. The instructions in this manual have been prepared to aid you in learning the proper procedures. Where information is of ...

  • Henny Penny OFG-391 - page 10

    Model OFG- 391 SECTION 2. INST ALLA TION This section provides the installation and unpacking instructions for the Henny Penny model OFG-391, open fryer . Installation of this unit should be performed only by a qualified service technician. Do not puncture the fryer with any objects such as drills or screws as component damage or electrical shock c ...

  • Henny Penny OFG-391 - page 11

    Model OFG- 391 Do not drop. The counterweights weigh approximately 18 lbs. (8.1 kg.) each. Handle with care, or personal injury could result. 8. Remove rear service cover . 9. Load the 4 weights into the counterweight assembly . 10 . Replace rear service cover . T o avoid personal injury and assure safe operation of unit, rear service cover must be ...

  • Henny Penny OFG-391 - page 12

    Model OFG- 391 Optional Ramp Unloading 2 - 3 7 03 ...

  • Henny Penny OFG-391 - page 13

    Model OFG- 391 908 2-4 ...

  • Henny Penny OFG-391 - page 14

    Model OFG- 391 2-3. SELECTING THE FR YER The proper location of the fryer is very important for operation, LOCA TION speed, and convenience. Choose a location which provides easy loading and unloading without interfering with the final assembly of food orders. Operators have found that frying from raw to finish, and holding the product in warmer pr ...

  • Henny Penny OFG-391 - page 15

    Model OFG- 391 2-5. VENTILA TION OF FR YER The fryer should be located with provision for venting into adequate exhaust hood or ventilation system. This is essential to permit efficient removal of the flue gases and frying odors. Special precaution must be taken in designing an exhaust canopy to avoid interference with the operation of the fryer . ...

  • Henny Penny OFG-391 - page 16

    Model OFG- 391 2-7. GAS PIPING • The fryer must be isolated from the gas supply piping (Continued) system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.45 KP A) (34.5 mbar). • A standard 3/4 inch, black steel pipe and malleable fitti ...

  • Henny Penny OFG-391 - page 17

    Model OFG- 391 403 2- 8 ...

  • Henny Penny OFG-391 - page 18

    Model OFG- 391 2-8. GAS LEAK TEST Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position. The word “OFF” is at the bottom of the knob when the valve is closed. After the piping and fittings have been installed, check for gas leaks. A simple checking method is to turn on the gas and brush a ...

  • Henny Penny OFG-391 - page 19

    Model OFG- 391 2-10. ELECTRICAL The gas fryer requires 120 volt, single phase 60 Hertz, 10 REQUIREMENTS amp, 3 wire grounded (earthed) service, or 230 volt, single phase, 50 Hertz service. The 120 volt gas fryer is factory equipped with a grounded (earthed) cord and plug for your protection against shock, and should be plugged into a 3 prong ground ...

  • Henny Penny OFG-391 - page 20

    Model OFG- 391 BOIL-OVER PREVENTION IN HENNY PENNY FR YERS F AILURE T O FOLLOW THESE INSTRUCTIONS CAN RESUL T IN SHOR TENING OVERFLOWING THE FR YPOT WHICH COULD CAUSE SERIOUS BURNS, PERSONAL INJURY . FIRE AND/OR PROPERTY DAMAGE. • THE SHOR TENING MA Y BE STIRRED ONL Y DURING THE MORNING ST AR T UP PROCEDURE. DO NOT STIR THE SHOR TENING A T ANY OT ...

  • Henny Penny OFG-391 - page 21

    Model OFG- 391 3-1. OPERA TING COMPONENTS COOK/PUMP Switch A three way switch with center OFF position; move the switch to the position marked COOK to operate the fryer; move the switch to the position marked PUMP to operate the filter pump; certain conditions must be met prior to operation of the filter pump; these conditions are covered later in ...

  • Henny Penny OFG-391 - page 22

    Model OFG- 391 3-1. OPERA TING COMPONENTS (Continued) High Limit This high temperature control senses the temperature of the shortening; if the temperature of the shortening exceeds 450°F (230°C), this control will open and shut off the heat to the frypot; when the temperature of the shortening drops to a safe operation limit, the control must be ...

  • Henny Penny OFG-391 - page 23

    Model OFG- 391 3-2. LID OPERA TION T o close lid: 1. Lower the lid until latch comes into contact with the pot. T o open lid: 1 . Unlatch the front lid latch. 2. Lift up on handle to raise lid. 3-3. SWITCHES AND Refer to image at end of this section. INDICA T ORS Fig. Item Description Function No. No. 3 - 2 1 Lights when the control calls for heat; ...

  • Henny Penny OFG-391 - page 24

    Model OFG- 391 3-3. SWITCHES AND INDICA T ORS (Continued) Fig. Item Description Function No. No. 3 -2 9 Press to access program modes; once in the Program Mode, it is used to advance to the next setting; if pressed along with it accesses the Information Mode which has historic information on the operator and fryer ’ s performance 3 -2 10 Used to ...

  • Henny Penny OFG-391 - page 25

    Model OFG- 391 403 3-5 14 1 2 3 4 5 6 7 8 9 13 1 1 12 10 Figure 3-2 ...

  • Henny Penny OFG-391 - page 26

    Model OFG- 391 3-4. CLOCK SET Upon initial start-up, or PC board replacement, if “CLOCK SET” automatically appears in the display , start with step 4. 1. Press and hold for 5 seconds until “LEVEL 2” shows in display . 2. Press and “CLOCK SET”, “ENTER CODE” shows in display . 3. Press . 4. “CS-1, SET , MONTH”, and the month flash ...

  • Henny Penny OFG-391 - page 27

    Model OFG- 391 3-4. CLOCK SET 14. Press and “CS-6, CLOCK MODE” shows in the (Continued) display , along with “1.AM/PM”. “1.AM/PM” is 12 hour time, “2.24-HR” is 24 hour time. Press to change. 15. Press and “CS-7, DA YLIGHT SA VINGS ADJ” shows in the display , along with “2.US”. Press to change to the following: a. “1.OFF” ...

  • Henny Penny OFG-391 - page 28

    Model OFG- 391 3-5. FILLING OR ADDING SHOR TENING The shortening level must always be above the heating elements when the fryer is heating and at the frypot level indicators on the r ear of the frypot (Figur e 3-3). Failur e to follow these instructions could r esult in a fir e and/or damage to the fryer . When using solid shortening, it is r ecomm ...

  • Henny Penny OFG-391 - page 29

    Model OFG- 391 3-6. PRODUCT RACKING RECOMMENDA TIONS The rack positions are referenced starting at the bottom: 4 _____________ 3 _____________ 2 _____________ 1 _____________ The bottom position is to be avoided on small loads because it is closer to the cold zone. (The oil is cooler at the bottom of the frypot and hotter at the top.) W ith bigger ...

  • Henny Penny OFG-391 - page 30

    Model OFG- 391 3-7. BASIC OPERA TION Follow the procedures below on the initial start-up of the fryer , and each time the fryer is brought from a cold, or shut down condition. 1 . Make sure the frypot is filled with shortening to the 2 lower level indicators DO NOT OVERLOAD, OR PLACE PRODUCT WITH EXTREME MOISTURE CONTENT INTO THE RACKS. 20 LBS. (9. ...

  • Henny Penny OFG-391 - page 31

    Model OFG- 391 3-7. BASIC OPERA TION 4. Allow fryer to heat until illuminates. (Continued) Bypass the Melt Cycle, if desired, by pressing a product button and holding it for five seconds. The display shows “EXIT MEL T? 1=YES 2=NO”. Press to exit melt. In the event of a power failure, no attempt should be made to operate the fryer . The fryer is ...

  • Henny Penny OFG-391 - page 32

    Model OFG- 391 3-7. BASIC OPERA TION 9. Unlatch and raise the lid cautiously . (Continued) 10. Using the rack handles, remove the racks of product from the carrier , starting with the top rack, to prevent damaged product. 1 1. If a Quality time (hold time) was programmed, the controller automatically starts the hold timer . The display alternately ...

  • Henny Penny OFG-391 - page 33

    Model OFG- 391 3-8. CARE OF THE SHOR TENING FOLLOW THE INSTRUCTIONS BELOW TO A VOID SHOR TENING OVERFLOWING THE FRYPOT , WHICH COULD RESUL T IN SERIOUS BURNS, PERSONAL INJURY , FIRE, AND/OR PROPER TY DAMAGE. 1. T o protect the shortening when the fryer is not in immediate use, the fryer should be put into the Idle Mode. 2. Frying breaded products r ...

  • Henny Penny OFG-391 - page 34

    Model OFG- 391 3-9. FIL TERING INSTRUCTIONS (continued) FIL TER ONL Y WHEN THE SHOR TENING TEMPERA TURE IS LESS THAN 275° F (135° C). FAILURE T O DO SO CAN RESUL T IN SHOR TEN- IN G OVERFLOWING THE FR YPOT , CAUSING SERIOUS BURNS, PERSONAL INJUR Y , AND/OR PROPER TY DAMAGE. High volume cooking could cause the cold zone to fill quicker with crackl ...

  • Henny Penny OFG-391 - page 35

    Model OFG- 391 3-9. FIL TERING INSTRUCTIONS (Continued) BRUSH ALL CRACKLINGS FROM FR YPOT SURF ACES AND THE COLD ZONE DURING THE FIL TERING PROCESS. FAILURE T O DO SO CAN RESUL T IN SHOR TENING OVERFLOWING THE FR YPOT , WHICH COULD CAUSE SERIOUS BURNS, PERSONAL INJURY , FIRE AND/OR PROPER TY DAMAGE. 5. When all of the shortening has drained, scrape ...

  • Henny Penny OFG-391 - page 36

    Model OFG- 391 c. Rinse the frypot interior . Especially work on hard to clean areas, like the frypot bottom and burner tubes. d . After thorough rinsing with shortening, close the drain valve. e. Turn the COOK/PUMP switch to the OFF position. ONL Y CONNECT AND DISCONNECT THE FIL TER RINSE HOSE WHEN THE MAIN POWER SWITCH IS IN THE OFF POSITION. ALS ...

  • Henny Penny OFG-391 - page 37

    Model OFG- 391 3-10. CHANGING THE FIL TER ENVELOPE (Continued) 4 . Lift the filter screen assembly from the drain pan. 5 . Wipe the shortening and crumbs from the filter drain pan. Clean the filter drain pan with soap and water . Thoroughly rinse with hot water . 6. Unthread the standpipe from the filter screen assembly . 7 . Remove the crumb catch ...

  • Henny Penny OFG-391 - page 38

    Model OFG- 391 3-1 1. LIGHTING AND T o light burner: SHUTDOWN OF THE 1. T urn COOK/PUMP switch to the OFF position. BURNERS 2. Rotate gas valve knob clockwise to the OFF position and wait at least five(5) minutes before continuing to next step. 3. Rotate gas valve knob counter clockwise to the ON position. 4. Place the electrical COOK/PUMP switch t ...

  • Henny Penny OFG-391 - page 39

    Model OFG- 391 3-12. FIL TER PUMP MOT OR The filter pump motor is equipped with a manual reset button, located on the rear of the motor , in case the motor overheats. W ait about 5 minutes before attempting to reset this protective device to allow motor to cool. Remove the access panel on the left side panel of the unit to reset the button. It take ...

  • Henny Penny OFG-391 - page 40

    Model OFG- 391 3-13. CLEANING THE FR YPOT 5 . Fill the frypot to the level indicators with hot water . (Continued) Add 8 to 10 ounces of fryer cleaner (Henny Penny part number 12101) to the water and mix thoroughly . Always wear chemical splash goggles or face shield and protective rubber gloves when cleaning the frypot as the cleaning solution is ...

  • Henny Penny OFG-391 - page 41

    Model OFG- 391 3-13. CLEANING THE FR YPOT 8 . After cleaning, turn off the COOK/PUMP switch. Open (Continued) the drain valve and drain the cleaning solution from the frypot into the filter drain pan and discard. 9 . Close the drain valve and refill the frypot with plain hot water to upper level indicator line. 1 0. Add approximately 16 ounces of d ...

  • Henny Penny OFG-391 - page 42

    Model OFG- 391 3-15. PREVENTIVE MAINTENANCE Before servicing the fryer: • Gas supply should be turned off to avoid fire or explosion. • Electrical supply should be unplugged or wall circuit breaker turned off to avoid electrical shock. Checking/Cleaning Dilution Box - Monthly Cleaning the dilution box helps to ensure the unit operates efficient ...

  • Henny Penny OFG-391 - page 43

    Model OFG- 391 3-15. PREVENTIVE Lubricating Lid Rollers - Annually MAINTENANCE (Continued) The lid rollers, in the back of the fryer , should be lubricated at least once a year , to allow the lid easy movement. 1. Remove the back shroud of the fryer . 2. Using spindle lube, part number 12124, place a small amount of lube on both top and bottom roll ...

  • Henny Penny OFG-391 - page 44

    Model OFG- 391 3-16. PROGRAMMING 3 . Press and release the desired product button (1 to 10). (Continued) Press to copy a product, erase a product, preset a product, erase all products, or preset all products. 4 . Press and release . The name of that product shows in the display . Ex. “ NAME“FRIES”. Change Product Names a. Press and release an ...

  • Henny Penny OFG-391 - page 45

    Model OFG- 391 3-15. PROGRAMMING 8. Press and release and “2. STEP 2 A T” shows in (Continued) display , along with a step 2 time. If no step 2 is desired, set time to “0:00” and press . If a step 2 is desired, press and set a time. Then press to set the temperature. Up to 10 steps can be programmed for a product, repeating the above step f ...

  • Henny Penny OFG-391 - page 46

    Model OFG- 391 1 1. Press and release and “LOAD COMP” shows in the display along with the load compensation value. This automatically adjusts the time to account for the size and temperature of the cooking load. Press and release to change this value to a max. of 20 and a min. of 0, or “OFF”. Preset at factory at 5. 12. Press and release an ...

  • Henny Penny OFG-391 - page 47

    Model OFG- 391 “2,Mixed” a . “FIL TER AFTER” shows in the display , along with the preset number of Cook Cycles. b. Press and release until the desired number of Cook Cycles between filters shows in the display . For example, if 4 is set for a product, each time that product is selected, it counts 1/4, or 25%. Then each time a product is co ...

  • Henny Penny OFG-391 - page 48

    Model OFG- 391 The following are examples of copying and erasing products: Copying Press to select the presently displayed “COPY A PROD” option. “COPY __ T O __” shows in display . The first set of “_” is blinking. Select the product you wish to copy from , for example, by pressing the button: “COPY 2 T O __” shows in display . Next ...

  • Henny Penny OFG-391 - page 49

    Model OFG- 391 3-17. SPECIAL PROGRAM The Special Program mode is used to set more detailed MODE parameters listed below . SP-1 · Degrees Fahrenheit or Celsius SP-2 · Language: English, French, German, Spanish, and Portuguese SP-3 · System initialization SP-4 · Audio volume SP-5 · Audio tone SP-6 · T ype of shortening to be melted - liquid, so ...

  • Henny Penny OFG-391 - page 50

    Model OFG- 391 Language (SP-2) a. Follow steps 1 and 2 above. b. Press and release button. “SP-2” and “LANGUAGE” flashes on the display , along with the language (Ex:” 1.ENGL”) c. T o toggle to the desired language, press and release . System Initialization (SP-3) This step resets the controls, but doesn’t erase product settings. a. F ...

  • Henny Penny OFG-391 - page 51

    Model OFG- 391 T ype of shortening to be melted - Liquid or Solid (SP-6) The Melt Cycle can be set to the type of shortening being used. a. Follow steps 1 and 2 above. b. Press and release 5 times. “SP-6” and “MEL T CYCLE SELECT” flashes on the display , along with “l=LIQ” or “2=SOLID”. c. Press to toggle from one type to another . ...

  • Henny Penny OFG-391 - page 52

    Model OFG- 391 3-17. SPECIAL PROGRAM e . Change the idle setpoint temperature, by pressing MODE (Continued) f. Press and release . “SP-7B” and “AUTO-IDLE MINUTES” shows in the display , along with the preset time. g . Press to set the minutes the cooker stays idle before the Auto-idle is enabled; 60 the maximum, OFF the minimum. Ex: “30? ...

  • Henny Penny OFG-391 - page 53

    Model OFG- 391 3-17. SPECIAL PROGRAM f . Press and “SP-8C” shows in the display , if YES MODE (Continued) was chosen in step e. “FIL TER LOCKOUT A T…” and a value between 100% and 200% shows in display . Press to change this value. g. Press and “SP-8D” shows in the display , followed by “LOCKOUT -HEA T OIL... and a temperature (pres ...

  • Henny Penny OFG-391 - page 54

    Model OFG- 391 3-17. SPECIAL PROGRAM MODE (Continued) SCHEDULE m . If “4,SCHED” is selected, “SP-8A” shows in the display , and followed by “SCHEDULE”. Press the and up to 4 different times of day can be programmed, by pressing . . EX: SP-8A “SCHEDULE” F1: 10.00A SP-8B “SCHEDULE” F2: 2.00P SP-8C “SCHEDULE” F3: 8.00P SP-8D ? ...

  • Henny Penny OFG-391 - page 55

    Model OFG- 391 3-17. SPECIAL PROGRAM Product Buttons (Sp-9) MODE (Continued) This mode allows you set up the way products are selected, and Cook Cycles started, in the cook mode. a. Follow steps 1 and 2 above. b. Press and release until “SP-9” and “PRODUCT BUTT ONS” flashes in the display . c. When using the first option, “1,COOK”, pres ...

  • Henny Penny OFG-391 - page 56

    Model OFG- 391 3-17. SPECIAL PROGRAM MODE (Continued) Program Code Change (SP-15) This allows the operator to change the program code (factory set at 1, 2, 3) used to access Product Programming, Special Programming, Clock Set, Data Comm, and Heat Control Modes. a. Follows steps 1 and 2 above. b. Press until “SP-15” and “CHANGE, MGR CODE, 1=YE ...

  • Henny Penny OFG-391 - page 57

    Model OFG- 391 e. If satisfied with code, press . “*CODE CHANGE*” shows in display . f. If not satisfied with code, press and *CANCELLED* shows in display , then reverts back to “SP-16” and “CHANGE USG CODE ? 1=YES”. Then the above steps can be repeated. Change Shortening-A-Cook Cycles (SP-17) The operator can set a reminder to filter t ...

  • Henny Penny OFG-391 - page 58

    Model OFG- 391 3-19. INFORMA TION MODE This mode gathers and stores historic information on the fryer and operator ’ s performance. Press and at the same time and “*INFO MODE*” shows on display . Press or to access the steps and press to view the statistics within each step. Information Mode is intended for technical use, but the operator can ...

  • Henny Penny OFG-391 - page 59

    Model OFG- 391 3-19. INFORMA TION MODE 2. LAST LOAD (Continued) Press to view the following information from the most recent Cook Cycle. FUNCTION DISPLA Y EX: T ime of day the last cook cycle was started STARTED 10.25A Product (Last product cooked) PRODUCT -2- Ready? (W as fryer Ready before start?) READY? YES S topped: T ime remaining, or secs pas ...

  • Henny Penny OFG-391 - page 60

    Model OFG- 391 3-19. INFORMA TION MODE 4. REVIEW USAGE (Continued) Press to view the accumulated information since the data was manually reset: FUNCTION DISPLA Y EX: Day the usage data was previously reset SINCE APR-19 Number of hours the fryer was on PWR ON HRS 165 Number of times oil was filtered FILTERED 34 T otal number of cook cycles TOTAL CK ...

  • Henny Penny OFG-391 - page 61

    Model OFG- 391 3-19. INFORMA TION MODE Press to view the specific status of each input. An (Continued) underscore (“_”) indicates the input is not presently detected. A checkmark (“ ”) indicates the signal is detecting a normal input. A blinking (“X”) indicates the signal is presently detected, but is detected as a half-wave (partially ...

  • Henny Penny OFG-391 - page 62

    Model OFG- 391 3-19. INFORMA TION MODE Press and “6. PMP_ AIR_” shows in display . (Continued) Press to view the amp “DRA W” status of the pump motor output and air valve output. “PMP ” and “AIR ” in the display means the amps are good. A flashing “X” behind the “PMP” or “AIR” means too much current. Press to view the No ...

  • Henny Penny OFG-391 - page 63

    Model OFG- 391 Power switch on but fryer completely inoperative Shortening not heating Foaming or boiling over Shortening not draining Filter motor won’t run Product Color Not Correct: A. T oo Dark B. T oo Light C. Product Greasy 4-1. TROUBLE SHOOTING GUIDE Problem Cause Correction • Open circuit • Drain valve open • High temperature limit ...

  • Henny Penny OFG-391 - page 64

    Model OFG- 391 4-2. ERROR CODES In the event of a control system failure, the digital display will show an Error Message. These messages are coded: “E-4”, “E-5”, “E-6”, “E-10”, “E-15”, “E-20 A-D”, “E41”, “E-46”, “E-47”, “E-48”, E-70B, E-92. A constant tone is heard when an error code is displayed, and to sile ...

  • Henny Penny OFG-391 - page 65

    Model OFG- 391 703 4-3 4-2. ERROR CODES (Continued) DISPLA Y CAUSE PANEL BOARD CORRECTION “E-41” Programming T urn switch to OFF position, then back to ON; if display failure shows “E-41”, the control should be re-initialized (see Pro- gramming Section); if the error code persists, replace the control panel “E-46” Eeprom memory T urn sw ...

  • Henny Penny OFG-391 - page 66

    Model OFG- 391 G L O S S A R Y HENNY PENNY OPEN FRYERS air valve a valve on the eight head fryer that allows air into the filter lines when the pump is on in the mixing mode on eight head fryers airflow switch a switch that senses the amount of airflow coming from the blower; if the airflow (gas fryers only) falls below a certain level, the switch ...

  • Henny Penny OFG-391 - page 67

    Model OFG- 391 data plate a label or plate located on the right side panel of the fryer that indicates the fryer type, serial number , warranty date, and other information drain handle the handle used to open and close the drain valve drain interlock switch a microswitch that automatically shuts off the fryer heat in the event the drain valve is in ...

  • Henny Penny OFG-391 - page 68

    Model OFG- 391 gas control valve an automatic dual controller that controls gas to both pilot lights and gas (gas fryers only) pressure to burners on fryers; if either pilot light goes out, the controller shuts off the gas to the other pilot light gas valve knob the knob that opens and closes the gas control valve (gas fryers only) gas pressure reg ...

  • Henny Penny OFG-391 - page 69

    Model OFG- 391 power/pump switch a three-way switch located on the front control panel of the fryer that serves as an off/on switch and a filter switch product a food item cooked in the fryer rack the wire grid that slides into the carrier to hold product during the cook cycle setpoint a preset cooking temperature; the setpoint is a programmable fe ...

  • Henny Penny OFG-391 - page 70

    *FM05-025-f* Henny Penny Corp., Eaton, Ohio 45320, Revised 8-6-10 Henny Penny Corporation P .O.Box 60 Eaton,OH 45320 1-937-456-8400 1-937-456-8402 Fax T oll free in USA 1-800-417-8417 1-800-417-8434 Fax w w w .hennypenny .com ...

Manufacturer Henny Penny Category Fryer

Documents that we receive from a manufacturer of a Henny Penny OFG-391 can be divided into several groups. They are, among others:
- Henny Penny technical drawings
- OFG-391 manuals
- Henny Penny product data sheets
- information booklets
- or energy labels Henny Penny OFG-391
All of them are important, but the most important information from the point of view of use of the device are in the user manual Henny Penny OFG-391.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Henny Penny OFG-391, service manual, brief instructions and user manuals Henny Penny OFG-391. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Henny Penny OFG-391.

Similar manuals

A complete manual for the device Henny Penny OFG-391, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Henny Penny OFG-391 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Henny Penny OFG-391.

A complete Henny Penny manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Henny Penny OFG-391 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Henny Penny OFG-391, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Henny Penny OFG-391, that we can find in the current document
3. Tips how to use the basic functions of the device Henny Penny OFG-391 - which should help us in our first steps of using Henny Penny OFG-391
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Henny Penny OFG-391
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Henny Penny OFG-391 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Henny Penny OFG-391?

Use the form below

If you did not solve your problem by using a manual Henny Penny OFG-391, ask a question using the form below. If a user had a similar problem with Henny Penny OFG-391 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)