English dropdown-ico

Manual Poulan 2001-02

17 pages 0.72 mb
Download

Go to site of 17

Summary
  • Poulan 2001-02 - page 1

    2250 / 2450 / 2550 Operator’s Manual Manual del Operador Manuel de L’utilisateur ENGLISH ES P AÑOL FRANÇAIS U L R 530088727 2/12/01 R Please do not return u nit t o retailer . Por favo r , no devu elva el ap arato al lugar de comp ra. V euillez ne pas retourner l’outil au détaillant. 1 - - 800 - - 554 - - 6723 www.poulan.com WAR NI N G : R ...

  • Poulan 2001-02 - page 2

    2 IDENTIFICATION OF SYMBOLS WAR N IN G ! This chai n saw can be dangero us! Careless or improp er use can cause serious or e ven f atal injury. Read and understand the Operator’s Manual before using the chain saw. Always use two hands when operating the chain saw. WAR N IN G ! Contact ing the guide bar tip wit h any object should be avoided; t ip ...

  • Poulan 2001-02 - page 3

    3 ing checked regularl y as chain saw noise can damage hearing. Secure hai r above shoulder lengt h. S Keep all parts of your body away from the chain when the engine is running. S Keep chil dren, bys tanders, and ani mals a minimum of 30 f eet (10 meters ) away f rom the work area. Do not allow other people or animals to be near the chain saw when ...

  • Poulan 2001-02 - page 4

    4 A void Pin ch - - Kickback: S Be ext remely aware of situat ions or ob- struc tions that can c ause material to pinch the top of or otherwise stop t he chain. S Do not cut m ore than one log at a tim e. S Do not twi st the saw as the bar is wit h- drawn from an undercut when bucking. A void Pull - - In: S Always begin cutting wit h t he engi ne a ...

  • Poulan 2001-02 - page 5

    5 bar tip. A Reduced - - Kic kback Guide Bar has been demonstrat ed to s ignifi cantly re- duce the number and seri ousness of kick - backs when tes ted in acc ordance wi th safet y requirement s for gasol ine powered chain saws as s et by ANS I B 175.1. Small Radius Tip Symmetrical Guide Bar Reduced Kick back Symmetrical Guide Bar Large Radius T i ...

  • Poulan 2001-02 - page 6

    6 Comput ed kickback an gle (CKA) T able BAR P/N Length CHAIN P/ N 952044370 14” 952051211 MODEL 952044418 16” 952051338 14 _ CKA without chain b rake 2250 2250/2450 16 _ 2550 18” 952044368 952051209 24 _ NOTE: This s aw compl ies with Federal OSHA regulat ions for c ommerci al logging. SAFETY NOTICE: Expos ure to vibrati ons through prolonge ...

  • Poulan 2001-02 - page 7

    7 S Pull the bar forward until the chai n is snug in the groove of t he bar. S Hold guide bar against the saw frame and instal l t he c hain brake. Mak e sure the ad- justi ng pin is aligned wi th the hole in the bar. Remember this pin mov es the bar for- ward and backward as t he screw i s turned. S Replace t he chain brake nut s and ti ghten fing ...

  • Poulan 2001-02 - page 8

    8 OPERA TION KNOW YOUR SA W READ THIS OPERA TOR’S MANUAL AND SAFETY RULES BEFO RE OPERATIN G YOUR CHAIN SAW . Compare the illustra tions with your u nit to familiarize yourself with the location of the various controls and adjus tments . Save t his m anual for future reference. Chain Adjust ment T ool (Bar T ool) Primer Bulb Fuel Mix Fill Cap Sta ...

  • Poulan 2001-02 - page 9

    9 FUEL ING & LUBRICAT ION W ARNING: Remove fuel cap slow ly when refueling. FUELING ENGINE This engine is certifi ed to operate on unleaded gas oline. Before operati on, gasoline mus t be mi xed wit h a good quali ty 2-cycle a ir- coole d engine oil. We recommend P oulan/W eed Eater R brand oil. If you do not use t his oil, us e a good quality ...

  • Poulan 2001-02 - page 10

    10 OFF FULL CHOKE Choke/ Fast I dl e (SIDE VIEW ) ST ARTING A W ARM ENGINE: S Move ON/S TOP swi tch to t he ON position. S Pull the choke/f ast i dle lev er out to t he full extent, then push t he lever bac k in com- pletely (to t he OFF pos ition). S Slowly pres s the prim er bul b 6 times . S Pull the st arter rope quickl y with your right hand u ...

  • Poulan 2001-02 - page 11

    11 ing y our saw bef ore you begin a major sawing operati on. S Squeeze the thrott le trigger and al - low the engine t o reach full s peed before cutt ing. S Begin cut ting with the saw frame against the l og. S Keep the engine at full speed the en- tire time you are cut ting. S Allow the chain to cut f or you. E xert only light downward press ure ...

  • Poulan 2001-02 - page 12

    12 NOTE: Before felling cut is c omplete, use wedges t o open the cut when necessary t o control the direc tion of fall. T o avoi d ki ckbac k and chain damage, us e wood or plas tic wedges, but never steel or i ron wedges. S Be alert to signs that t he tree is ready to fall: c racking sounds, wideni ng of the fell- ing cut, or m ovement i n the up ...

  • Poulan 2001-02 - page 13

    13 2 nd Cut 1 st Cut 1 st Cut 2 nd Cut Using a support stand 1 st Cut 2 nd Cut LIMBING AND PRUNING W ARNING: B e al ert for and guard against kickback. Do not allow t he moving chain t o contact any other branches or objects at the nose of t he guide bar when limbing or pruning. Allowing such contact can result in ser ious injur y . W ARNING: Nev e ...

  • Poulan 2001-02 - page 14

    14 MAINTENANCE SCHEDULE Lubric ate bar sprocket hole After each use ....... Check: Fuel m ixture level Before each use .... Bar lubrication Before each use ....... Chain tensi on B efore eac h use ....... Chain sharpness Before each use .... For damaged parts Before each use .. For loose caps Before each use ...... For loose fastene rs Before each ...

  • Poulan 2001-02 - page 15

    15 S Burring of guide bar rai ls is a normal process of rai l wear. Remove these burrs with a flat file. S When rai l t op is uneven, use a flat f ile to re- store s quare edges and s ides. Correct Groove Worn Groove File Rail E dges and Sides Square Replace guide bar when the groove is w orn, the guide bar i s bent or c racked, or when exces s hea ...

  • Poulan 2001-02 - page 16

    16 TROUBLE CAUSE REMEDY Engine will not start or w ill run only a few seconds af ter starti ng. S Ignition swit ch off . S Engine flooded. S Fuel tank empt y. S Spark plug not f iring. S Fuel not reaching carburetor . . S Move ign ition switch to ON. S See “Diff icult St arting” i n Operation Sec tion. S Fill tank with correct fuel m ixture. S ...

  • Poulan 2001-02 - page 17

    17 nance of your lawn and garden equipment en - gine. Y our emission control system i ncludes parts such as the carbur etor and th e ignition system. Where a warrantable condit ion exit s, Poulan/Weed Eater will repair your lawn and garden equipment engine at no cost to you. E x - penses covered under w arr anty include diag- nosis, parts and l abo ...

Manufacturer Poulan Category Chainsaw

Documents that we receive from a manufacturer of a Poulan 2001-02 can be divided into several groups. They are, among others:
- Poulan technical drawings
- 2001-02 manuals
- Poulan product data sheets
- information booklets
- or energy labels Poulan 2001-02
All of them are important, but the most important information from the point of view of use of the device are in the user manual Poulan 2001-02.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Poulan 2001-02, service manual, brief instructions and user manuals Poulan 2001-02. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Poulan 2001-02.

Similar manuals

A complete manual for the device Poulan 2001-02, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Poulan 2001-02 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Poulan 2001-02.

A complete Poulan manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Poulan 2001-02 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Poulan 2001-02, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Poulan 2001-02, that we can find in the current document
3. Tips how to use the basic functions of the device Poulan 2001-02 - which should help us in our first steps of using Poulan 2001-02
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Poulan 2001-02
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Poulan 2001-02 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Poulan 2001-02?

Use the form below

If you did not solve your problem by using a manual Poulan 2001-02, ask a question using the form below. If a user had a similar problem with Poulan 2001-02 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)