-
DigiTech CR-7 - page 1
...
-
DigiTech CR-7 - page 2
DECLARA TION OF CONFORMITY Manufacturer’ s Name: DigiT ech Manufacturer’ s Addr ess: 8760 S. Sandy Parkwa y Sandy , Utah 84070, USA declares that the product: Product name: HardWire CR-7 Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.) conforms to the following Product S ...
-
DigiTech CR-7 - page 3
WARRANTY : W e at DigiT ech are proud of our pr oducts and back-up each one with the following war ranty: The warranty registration car d must be mailed within ten da ys after purchase date to validate this warranty . DigiT ech warrants this product, when used solely within the U.S., to be free from defects in materials and w orkmanship under norma ...
-
DigiTech CR-7 - page 4
...
-
DigiTech CR-7 - page 5
1 Introduction More than a remar kable achievement, HardWire ™ represents a collection of significant improv ements in effects pedals for guitar . HardWire pedals provide a suite of well-known effects, each with super ior tone and control. But these pedals go above and beyond their peer s to provide such distinguishing fea- tures as tr ue bypass, ...
-
DigiTech CR-7 - page 6
2 2 3 4 5 6 7 8 11 12 8 9 10 1 ...
-
DigiTech CR-7 - page 7
3 W hat Does This Do? Le vel Knob - Controls the chor us level. T ur n this knob clockwise to increase and counter -clockwise to decrease the chor us level. DC Adapter Jack - Connect (an optional) Har man PS200R pow er supply to this jack. Use the proper supply for your area’ s mains line voltage . Speed Knob - Controls the modulation speed of th ...
-
DigiTech CR-7 - page 8
4 MODERN – dual voice chor using that’ s both ver y r ich and s mo ot h . BOUTIQUE – a r ich chor us with the quir kiness of analog c ir cu i ts . ANALOG – distinctively organic bucket-brigade chor us. JAZZ – singl e voi ce cho r usi ng wit h a dr y outpu t – jazz ers re joic e! VINT AGE – war m and ver satile from subtle to euphor ic ...
-
DigiTech CR-7 - page 9
5 Input 2 - Conne ct a seco nd inp ut to thi s jack for ste reo op eratio n. Inp uts 1 and 2 are proce sse d sepa ratel y throu gh the stere o chorus eff ec t and the n fed to Outpu ts 1 and 2 ke epin g tr ue st ereo separa- tio n betw ee n chan nels . F oot Switch Release Pins - These two pins are spring loaded hinges that hold the Foot Switch in ...
-
DigiTech CR-7 - page 10
6 Output 2 - Connect this output to a second guitar amplifier when two amplifier s are being used. Note: Use unbalanced mono instrument cables only . 12. ...
-
DigiTech CR-7 - page 11
7 Amp Setup PS200R (optional) or ...
-
DigiTech CR-7 - page 12
8 Ef fects Loop Setup Note: If the amp effects loop has a mix control, set the mix to 100% full wet. AMP RETURN AMP SEND PS200R (optional) ...
-
DigiTech CR-7 - page 13
9 Batter y Operation In the event that batter y pow er is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remov e the pedal from your pedal chain if the batter y is dead. T o replace the batter y , do the follo wing: Using the tip of a 1/4” guitar cable , push in one of the Release Pins in on eit ...
-
DigiTech CR-7 - page 14
10 Switch is proper ly fastened, both Release Pins are flush with the outer side of the pedal. Foot Switch Pedal Switch Arm Foot Switch Release Pin 9VDC Battery Foot Switch Release Pin Pedal Chassis Battery Compartment Spring ...
-
DigiTech CR-7 - page 15
11 HardWire P erfor mance Accessories The performance accessor ies make integr ating a HardWire pedal into any pedal board a snap. The follo wing accessories are included: Hook-and-loop P edalboard Pad (designed to attach to the surfaces found on most commercial pedal boards) Foot Switch Glow Sticker (easily visible on dar k stages) StompLock ™ ( ...
-
DigiTech CR-7 - page 16
12 Hook-and-loop Pedalboard P ad T o attach the P edalboard P ad, do the following: P eel off the existing r ubber skid pad from the bottom of the pedal. P eel the adhesive protector from the back of the P edalboard Pad. Apply the P edalboard Pad to the bottom of the pedal. 1. 2. 3. ...
-
DigiTech CR-7 - page 17
13 F oot Switch Glow Sticker T o attach the Foot Switch Glow Sticker , do the following: P eel the adhesive backing from the Foot Switch Glow Sticker . Apply the Glow Sticker to the top of the Foot Switch. 1. 2. ...
-
DigiTech CR-7 - page 18
14 StompLock T o place the StompLock over the pedal knobs, do the follo wing: Set the knobs to your prefer red setting. Gently push the StompLock ov er the top of the knobs. T o remo ve the StompLock, gently lift one side and then the other . 1. 2. 3. ...
-
DigiTech CR-7 - page 19
15 Specifications Controls - Level, Speed, Depth, T ype , On/Off P edal Jacks - Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Input Impedance - >1 M Ω (stereo), >500 k Ω (mono) - effect on Output Impedance - 1 k Ω - effect on Input Impedance - tr ue hardwire bypass - effect off Output Impedance - tr ue hardwire bypass - effect off P o ...
-
DigiTech CR-7 - page 20
8760 South Sandy Parkwa y Sandy , Utah 84070 PH (801) 566-8800 F AX (801) 566-7005 HardWir e and DigiT ech are trademarks of the Harman Music Group Inc . Cop yright - Harman Music Gr oup Manufactured in the USA HardWir e CR-7 Owners Manual 18-0618-A Please visit us on the W orld Wide W eb at: www .digitech.com ...
Do you have a question concerning DigiTech CR-7?
Use the form below
If you did not solve your problem by using a manual DigiTech CR-7, ask a question using the form below. If a user had a similar problem with DigiTech CR-7 it is likely that he will want to share the way to solve it.