English dropdown-ico

Manual Kenwood KRC-208S

25 pages 0.32 mb
Download

Go to site of 25

Summary
  • Kenwood KRC-208S - page 1

    KRC-208S KRC-218 KRC-28MR © B64-1538-00 (KW) CASSETTE RECEIVER INSTRUCTION MANUAL AMPLI-TUNER-LECTEUR DE CASSETTE MODE D’EMPLOI RADIO CASETE MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new cassette-receive ...

  • Kenwood KRC-208S - page 2

    — 2 — English Contents Before use Safety precautions ........................................................................3 General features Power ............................................................................................5 Switching Modes ..........................................................................5 Volume ... ...

  • Kenwood KRC-208S - page 3

    — 3 — To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery, or ground wires, make sure to use automotive- grade wires or other wires with a 0.75mm 2 (AWG18) or more to prevent wire ...

  • Kenwood KRC-208S - page 4

    — 4 — English • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer. • Characters in the LCD may become difficult to read in temperatures below 41 ˚F (5 ˚C). • T ...

  • Kenwood KRC-208S - page 5

    Switching Modes: Each time you press the SRC (source) button, the mode switches as follows: Selecting standby mode: Press the SRC button repeatedly and switch to "OFF" . When "OFF" is displayed, the standby mode is activated. The standby mode turns all functions off while leaving the power to the unit on. Use this mode when you ...

  • Kenwood KRC-208S - page 6

    "BAL" : Adjust the balance level. Setting values: Left 15 – Right 15 "TRE" : Adjust the treble level. Setting values: - 4 – + 4 "BAS" : Adjust the bass level. Setting values: - 4 – + 4 Press the AUD button for at least one second to enter the control mode. Selecting mode Press either the FM or AM button. Each tim ...

  • Kenwood KRC-208S - page 7

    Adjust the time. When the time is not displayed, first press the CLK button to display the time. Press the CLK button for at least one second to enter the clock adjustment mode. The time display will blink. • Adjusting the hours Press the FM button to advance the hours, or press the AM button to make the hours go back. • Adjusting the minutes P ...

  • Kenwood KRC-208S - page 8

    T uner features The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate: Press the release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special st ...

  • Kenwood KRC-208S - page 9

    You can automatically store all the receivable frequencies in the band currently being listened to, and then recall them with the touch of a button later. This function is especially useful when you are travelling and do not know what stations are available. Up to six frequencies can be stored this way. Select the band for auto memory entry. Press ...

  • Kenwood KRC-208S - page 10

    Cassette player features Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. The factory default for this function is ON. Turning CRSC On/Off: Press the CRSC button for at least one second to turn the function on/off. The indicator lights up when CRSC is on. Strong electrical fields ( ...

  • Kenwood KRC-208S - page 11

    Switch automatically to the tuner while you are rewinding or fast forwarding the tape. Turning Tuner Call On/Off: Press the T.C(T.CALL) button to switch tuner call on and off. The T.CALL indicator lights up when tuner call is turned on. Tuner Call Fast Forwarding Tapes: Press the FF button. The tape indicator blinks in the direction of the tape as ...

  • Kenwood KRC-208S - page 12

    Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point. Fast Forwarding and Reversing Disc Play This function permits the connection of optional players and the playing of discs. Playing Discs: Press the SRC button repeatedly to select the external disc control mode. The disc will start playing. Th ...

  • Kenwood KRC-208S - page 13

    Repeat playing the track or the disc currently being listened to. Turning Repeat Play On/Off: Press the REP button to switch repeat track/disc play on and off as follows: The REP indicator lights up when repeat play is turned on. The track number blinks in the display when track repeat is on. The disc number blinks in the display when disc repeat i ...

  • Kenwood KRC-208S - page 14

    Play the tracks on all the discs in the disc changer in random order. Press the M.RDM button to switch magazine random play on and off. The RDM indicator lights up when magazine random play is turned on. The disc and track numbers will change over and over in the display as the next track is being selected. When the disc/track has been selected, pl ...

  • Kenwood KRC-208S - page 15

    To change the track being heard, press the ¢ button. Another disc/track will be selected and played. • Magazine random play is canceled when you eject the disc. • The time needed for random selection depends on the number of discs loaded in the disc magazine. NOTE 2 — 15 — KRC-208S_U.S-1 00.12.26 4:00 PM Page 15 ...

  • Kenwood KRC-208S - page 16

    English — 16 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2 CAUTION Accessories ..........................................1 ..........................................1 ..........................................2 ........... ...

  • Kenwood KRC-208S - page 17

    FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT. CONT. — 17 — Connecting Wires to Terminals When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left ...

  • Kenwood KRC-208S - page 18

    English — 18 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). NOTE Accessory 2 Metal mounting strap Self-tapping screw (commercially available) Firewall or metal support Accessory 4 Installation ■ Installation 8 mm MAX. ø 5mm ø 5mm 8mm MAX. Installing in ...

  • Kenwood KRC-208S - page 19

    — 19 — Installation Removing the hard rubber frame ■ When the lower level is removed, remove the upper two locations. 2 The frame can be removed from the top side in the same manner. NOTE Catch Lock Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure ...

  • Kenwood KRC-208S - page 20

    English — 20 — Installation Accessory 7 Screwing the Faceplate on the Unit (KRC-208S / 218 only) ■ Never insert the taptite screw ( ø 4 × 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. 2 CAUTION If you want to fasten the fa ...

  • Kenwood KRC-208S - page 21

    — 21 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. Troubleshooting Guide SOLUTION POSSIBLE CAUSE PROBLEM The tape head is dirty. Clean the tape head, referring to the section on "Cleaning the tape ...

  • Kenwood KRC-208S - page 22

    English — 22 — Troubleshooting Guide External disc control mode The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p.4). The disc control mode cannot be selected. No wire has been connected to the disc changer input terminal on the unit. Connect the wire to the disc changer input terminal on the u ...

  • Kenwood KRC-208S - page 23

    — 23 — Troubleshooting Guide The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. Nothing has been recorded on the MD. ] The next MD will automatically be played. E-10 No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. ] Load the disc mag ...

  • Kenwood KRC-208S - page 24

    English — 24 — Specifications subject to change without notice. Specifications FM tuner section Frequency range (200 kHz space) .............87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) .....................9.3dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) ................ 15.2dBf (1.6 µV/75 Ω ) Frequency response (±3.0 d ...

  • Kenwood KRC-208S - page 25

    KRC-208S_U.S-1 00.12.26 4:00 PM Page 25 ...

Manufacturer Kenwood Category Car Stereo System

Documents that we receive from a manufacturer of a Kenwood KRC-208S can be divided into several groups. They are, among others:
- Kenwood technical drawings
- KRC-208S manuals
- Kenwood product data sheets
- information booklets
- or energy labels Kenwood KRC-208S
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kenwood KRC-208S.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kenwood KRC-208S, service manual, brief instructions and user manuals Kenwood KRC-208S. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kenwood KRC-208S.

Similar manuals

A complete manual for the device Kenwood KRC-208S, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kenwood KRC-208S by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kenwood KRC-208S.

A complete Kenwood manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kenwood KRC-208S - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kenwood KRC-208S, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kenwood KRC-208S, that we can find in the current document
3. Tips how to use the basic functions of the device Kenwood KRC-208S - which should help us in our first steps of using Kenwood KRC-208S
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kenwood KRC-208S
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kenwood KRC-208S in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kenwood KRC-208S?

Use the form below

If you did not solve your problem by using a manual Kenwood KRC-208S, ask a question using the form below. If a user had a similar problem with Kenwood KRC-208S it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)