English dropdown-ico

Manual Lenovo K430

57 pages 4.97 mb
Download

Go to site of 57

Summary
  • Lenovo K430 - page 1

    IdeaCentr e K430/K410 Har dwar e Maint enance Manual i d e a i d e a i d e a C e nt r e i d e a Machine T ypes: 10086/3109/4743 K430; 10089/1168/4744 K410 ...

  • Lenovo K430 - page 2

    ...

  • Lenovo K430 - page 3

    IdeaCentr e K430/K410 Har dwar e Maint enance Manual Machine T ypes: 10086/3109/4743 K430; 10089/1168/4744 K410 ...

  • Lenovo K430 - page 4

    ...

  • Lenovo K430 - page 5

    Contents Chapter 1. About this manual . . . . . . 1 Important Safety Information . . . . . . . . . . 1 Chapter 2. Safety information . . . . . . 3 General safety . . . . . . . . . . . . . . . . 3 Electrical safety . . . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . . 5 Handling electrostatic discharge-sensitive devices . . ...

  • Lenovo K430 - page 6

    iv IdeaCentre K430/K410Hardwar e Maintenance Manual ...

  • Lenovo K430 - page 7

    Chapter 1. About this manual This manual contains service and refer ence information for IdeaCentr e K430 & K410 computers listed on the cover . It is intended only for trained servicers who ar e familiar with Lenovo computer products. Before servicing a L enovo pr oduct, be sur e t o read the Safety Information. The description of the TV card ...

  • Lenovo K430 - page 8

    2 IdeaCentre K430/K410Hardwar e Maintenance Manual ...

  • Lenovo K430 - page 9

    Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer . General safety F ollow these rules to ensur e general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting any heavy object: 1. Ensure you can stand sa ...

  • Lenovo K430 - page 10

    Observe the following rules when working on electrical equipment. Important: Use only appr oved t ools and test equipment. Some hand tools have handles covered with a soft material that does not insulat e you when working with live electrical currents. Many customers have, near their equipment, rubber oor mats that contain small conductive be ...

  • Lenovo K430 - page 11

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had r equired safety it ems installed to protect users and service personnel from injury . This guide addresses only thos ...

  • Lenovo K430 - page 12

    • A void contact with other people while handling the part. • Wear a gr ounded wrist strap against your skin t o eliminate static on your body . • Pr event the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist str ap. • Use the black side of a gr ounded work mat to provide a ...

  • Lenovo K430 - page 13

    T o Connect T o Disconnect 1. T urn everything OFF . 2. First, attach all cables to devices. 3. Attach signal cables to connectors. 4. Attach power cor ds to outlet. 5. T urn device ON. 1. T urn everything OFF . 2. First, r emove power cords fr om outlet. 3. Remove signal cables from connectors. 4. Remove all cables fr om devices. CA UTION: When re ...

  • Lenovo K430 - page 14

    ≥18 kg(37 lbs) ≥32 kg(70.5 lbs) ≥55 kg(121.2 lbs) CA UTION: Use safe pr actices when lifting. CA UTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have mor e than one power cord. T o remove all electrical current from the ...

  • Lenovo K430 - page 15

    Chapter 3. Gener al information This chapter provides gener al information that applies to all machine types supported by this publication. Specications This section lists the physical specications for your computer . This section lists the physical specications for your computer . T ype IdeaCentr e K430 & K410 This section lists the p ...

  • Lenovo K430 - page 16

    10 IdeaCentre K430/K410Hardwar e Maint enance Manual ...

  • Lenovo K430 - page 17

    Chapter 4. Gener al Check out Attention: The drives in the computer you are servicing might have been r earranged or the drive startup sequence changed. Be extr emely car eful during writ e oper ations such as copying, saving, or formatting. Data or progr ams can be overwritten if you select an incorr ect drive. General error messages appear if a p ...

  • Lenovo K430 - page 18

    12 IdeaCentre K430/K410Hardwar e Maint enance Manual ...

  • Lenovo K430 - page 19

    Chapter 5. Using the Setup Utility The Setup Utility pr ogram is used t o view and change the congur ation settings of your computer , regar dless of which operating system you are using. However , the oper ating-system settings might override any similar settings in the Setup Utility pr ogram. Starting the Lenovo BIOS Setup Utility progr am T o ...

  • Lenovo K430 - page 20

    Administrator P assword Setting an Administr ator Passwor d det ers unauthoriz ed persons fr om changing conguration settings. Y ou might want to set an Administrat or P assword if you are responsible for maintaining the settings of sever al computers. After you set an Administrator P assword, a password pr ompt is displayed every time you acces ...

  • Lenovo K430 - page 21

    T o set a Power -On P assword, do the following: 1. Start the L enovo BIOS Setup Utility pr ogram (See ”Starting the L enovo BIOS Setup Utility pr ogram” on page 13.) 2. F rom the Security menu, select Set Power -On P assword and pr ess the Enter key . 3. The passwor d dialog bo x will be displayed. T ype the password, and pr ess the Enter key ...

  • Lenovo K430 - page 22

    USB Setup press the Enter key, and then select USB F unctions . A T A Device Setup pr ess the Enter key . Select Congure SA T A as , pr ess the Enter k ey and then select SA T A mode. Audio Setup press the Enter key, and then select Onboar d Audio Controller . Network Setup pr ess the Enter key, then select Onboard E thernet Support or Boot Agen ...

  • Lenovo K430 - page 23

    b. If you have changed these settings and want t o r eturn t o the default settings, select Load Optimal Defaults fr om the menu. Exiting the L enovo BIOS Setup Utility pr ogram After you nish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility progr am main menu. Y ou might have to press the Esc key sever ...

  • Lenovo K430 - page 24

    18 IdeaCentre K430/K410Hardwar e Maint enance Manual ...

  • Lenovo K430 - page 25

    Chapter 6. Symptom-t o-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is list ed rst. Always begin with Chapter 4, “General Checkout, ” on page 11. This inde x can also be used to help you decide which FRUs to have available when servicing a computer . If you ar e unable to correct the pr o ...

  • Lenovo K430 - page 26

    POS T error codes Each time you turn the computer on, it performs a series of tests to check that the syst em is oper ating correctly and that certain options ar e set. This series of tests is called the Power -On Self- T est , or POS T . POST does the following: • Checks some basic system-boar d operations • Checks that the memory is working c ...

  • Lenovo K430 - page 27

    Chapter 7. L ocations This section provides illustrations to help locate the various connectors, controls and components of the computer . Identifying internal components The following illustration shows the components inside your comput er . 1 2 3 5 4 6 1 Optical disk drive 4 Memory modules 2 Hard disk drive 5 Syst em fan 3 Gr aphics card 6 P ower ...

  • Lenovo K430 - page 28

    IdeaCentre K430 1 2 3 4 5 8 9 6 7 1 0 1 1 1 3 1 2 1 4 1 5 1 6 1 7 1 12V power connector 10 F ront USB connector 2 Micr oprocessor and heat sink 11 F ront USB connector 3 Micr oprocessor fan connector 12 Mode SW connector 4 Memory slots (4) 13 Serial (COM2)connector 5 P ower connect or 14 Batt ery 6 Mini PCI Express slot 15 LPC debug connector 7 PCI ...

  • Lenovo K430 - page 29

    IdeaCentre K410 1 2 3 4 5 6 7 8 9 1 0 1 1 1 2 1 4 1 3 1 6 1 7 1 5 1 8 1 9 2 0 1 12V power connector 10 P ower fan header 2 Micr oprocessor and heat sink 11 F ront panel connector 3 Micr oprocessor fan connector 12 Clear CMOS jumper 4 Memory slots (2) 13 F ront USB connectors (2) 5 Thermal sensor header connect or 14 Mini PCI Express slot 6 P ower c ...

  • Lenovo K430 - page 30

    24 IdeaCentre K430/K410Hardwar e Maint enance Manual ...

  • Lenovo K430 - page 31

    Chapter 8. Replacing hardwar e Attention: Do not r emove the computer cover or att empt any repair befor e r eading the “Important safety information” in the Safety and W arranty Guide that was included with your computer . T o obtain copies of the Safety and Warr anty Guide, go to the Support Web sit e at: http://consumersupport.lenovo.com Gen ...

  • Lenovo K430 - page 32

    Replacing the keyboar d and mouse Note: Y our keyboard will be connected to a USB connect or at either front or at the rear of the comput er . T o r eplace the keyboard: Step 1. Remove any media (disks, CDs, or memory cards) from the drives, shut down the computer , and turn off all attached devices. Step 2. Unplug all power cor ds from electrical ...

  • Lenovo K430 - page 33

    Step 5. Slide the computer cover out t o remove it. Step 6. T o r einstall the comput er cover: a. Line up the comput er cover with the chassis then slide it back. b. Secur e the comput er cover t o the chassis with the scr ews. Removing the front bez el Note: F or this procedure, it helps to lay the comput er at. T o r emove the front bezel: St ...

  • Lenovo K430 - page 34

    Step 2. Remove the fr ont bez el by r eleasing the three plastic tabs inside the chassis and sliding the be zel out as shown. Step 3. T o reattach the bez el, align the plastic tabs on the bott om of the be zel with the corresponding holes in the chassis, and then snap it int o position. Replacing a memory module Note: F or this procedure, it helps ...

  • Lenovo K430 - page 35

    Step 4. P osition the new memory module over the memory connector . Make sure that the notch 1 on the memory module aligns corr ectly with the connector key 2 on the syst em board. P ush the memory module str aight down into the connector until the retaining clips close. Step 5. Reattach the comput er cover . Replacing a hard disk drive Note: F or ...

  • Lenovo K430 - page 36

    Step 4. Remove the hard disk drive from the plastic br acket as shown. Step 5. Line up the new har d disk drive with the plastic br acket and snap it int o position. Step 6. Slide the new hard disk drive into the drive bay and slide the drive bay into place. Step 7. Connect the power and signal cables to the new hard disk drive. Step 8. Reattach th ...

  • Lenovo K430 - page 37

    Replacing a gr aphics card Note: F or this procedure, it helps to lay the comput er at. T o r eplace a graphics card: Step 1. Remove the computer cover . Refer t o “Removing the computer cover ”. Step 2. F ollow the below steps to r emove a gr aphics card: If your comput er has a Duo-graphics cards installed, follow the steps below to replac ...

  • Lenovo K430 - page 38

    b. Remove the scr ew that secures the graphics card latch to the chassis, open it, and remove the Duo-graphics car ds connector . 1 2 3 4 c. Remove the gr aphics car d by pulling it straight out of the connector . If your comput er has a single graphics card installed, follow the steps below to replace it: 32 IdeaCentre K430/K410Hardwar e Maint ena ...

  • Lenovo K430 - page 39

    a. Remove the scr ew that secur es the graphics latch t o the chassis and open it. 1 2 3 b. Remove the gr aphics car d by pulling it straight out of the connector . Step 3. Install the new adapter into the same adapter connector . Step 4. T urn the graphics card latch to the closed position and secur e it with the scr ew. Step 5. Connect the two gr ...

  • Lenovo K430 - page 40

    T o replace the TV - T uner card: Step 1. Remove the computer cover . Refer t o “Removing the computer cover ”. Step 2. Remove the scr ew that secur es the gr aphics car d latch t o the chassis and open it. 1 2 3 1 2 3 Step 3. Remove the TV- T uner card by pulling it straight out of the connector . Step 4. Install the new TV -tuner into the sam ...

  • Lenovo K430 - page 41

    Step 6. Reattach the comput er cover . Replacing the P ower supply Note: F or this procedure, it helps to lay the comput er at. T o r eplace the P ower supply: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) fr om the drives, shut down the oper ating system, and turn off the computer and all attached devices. Step 2. Unplug all powe ...

  • Lenovo K430 - page 42

    Step 1. Remove any media (disks, CDs, DVDs, or memory cards) fr om the drives, shut down the oper ating system, and turn off the computer and all attached devices. Step 2. Unplug all power cor ds from electrical outlets. Step 3. Disconnect all cables attached to the computer . This includes power cor ds, input/output (I/O) cables, and any other cab ...

  • Lenovo K430 - page 43

    Step 3. Disconnect all cables attached to the computer . This includes power cor ds, input/output (I/O) cables, and any other cables that are connect ed t o the comput er . Refer to “L eft and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover . Refer t o “Removing the computer cov ...

  • Lenovo K430 - page 44

    Step 4. Remove the computer cover . Refer t o “Removing the computer cover ”. Step 5. Remove the micropr ocessor fan. Refer to “Replacing the micropr ocessor fan”. Step 6. Remove the heat-sink. Refer t o “Replacing the heat-sink”. Step 7. T o remove the micropr ocessor 3 fr om the system boar d, press then slide the small handle out to ...

  • Lenovo K430 - page 45

    Step 8. Holding the sides of the micr oprocessor with your ngers, r emove the pr otective cover 1 that prot ects the gold contacts on the new microprocessor . 2 Step 9. Holding the sides of the microprocessor with your ngers, position the micropr ocessor so that the notches on the micropr ocessor are aligned with the tabs in the microprocesso ...

  • Lenovo K430 - page 46

    T o r eplace the Wi-Fi car d: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) fr om the drives, shut down the oper ating system, and turn off the computer and all attached devices. Step 2. Unplug all power cor ds from electrical outlets. Step 3. Disconnect all cables attached to the computer . This includes power cor ds, input/output ( ...

  • Lenovo K430 - page 47

    Step 2. Unplug all power cor ds from electrical outlets. Step 3. Disconnect all cables attached to the computer . This includes power cor ds, input/output (I/O) cables, and any other cables that are connect ed t o the comput er . Refer to “L eft and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove th ...

  • Lenovo K430 - page 48

    Notes: FRUs that have a 1 or 2 in the CRU column ar e Customer Replaceable Units (CRUs). • 1 – identies parts that are fairly simple t o replace, requiring few or no tools. • 2 – identies parts that are slightly mor e difcult t o replace. • N -identies parts that ar e not to be replaced by the customer . Description Lenovo P/N ...

  • Lenovo K430 - page 49

    MT8JTF25664AZ-1G4D1 2GB DDRIII1333 RAM(R) 1007003 HMT351U6CFR8C-H9 4GB D3-1333 RAM-HF 1100203 MT16KTF51264AZ-1G4M1 4GB D3-1333 RAM-HF 1100204 EBJ41UF8BDW0-GN-F 4GB D3-1600 RAM-HF 1100216 Mic_R D9PFW 4GB DDRIII1333 RAM(R) 1100188 Mic_S D9PFW 4GB DDRIII1333 RAM(R) 1100189 P sc_S A3P2GF3CKF-GDJ 4GB D3-1333 RAM(R) 1100154 Elp_R J2108BCSE-DJ-F 4GB DDRII ...

  • Lenovo K430 - page 50

    Hard Disk Drive Seagate Phar aoh6Gb/s ST3500413AS 500G HDDLH 16200064 WD XL500SM6G WD5000AAKX083CA1 500G HDDLH 16200031 Seagate Phar aoh 4K ST500DM002 500G HDDLH 16200178 Seagate Phar aoh6Gb/s ST31000524AS 1TB HDDLH 16200065 WD XL500SM6G WD10EALX089BA1 1TB HDDLH 16200032 Seagate Grenada S T1000DM003 1TB HDDLH 16200182 Seagate Grenada S T1500DM003 1 ...

  • Lenovo K430 - page 51

    Bitland @Geforce G T 630@2G/A/DB/H Gr aphic Card 11200899 P ower Supply HuntKey HK380-12GP S2(S7) A TX280W P ower Supply 36-200158 LiteonPS-5281-7VR5-RoHS A TX280W P ower Supply 36-200157 AcBelPC6001-EL9G A TX280W P ower Supply 36-200156 FSP280-50EP A A TX280W 85% P ower Supply 36-200161 LiteonPS-5281-02V A-RoHS A TX280W 85% P ower Supply 36-200160 ...

  • Lenovo K430 - page 52

    Cables Luxshare460mm Thermal Cable 6PIN(R) 31034561 Grandsun 460mmThermal Cable 6PIN(R) 31045784 Grandsun 2H300mmSA T A Cable with Latch(R) 31024767 Luxshare 2H300mmSA T A Cable with Latch(R) 31024785 Grandsun 2H300mmSA T A Cable with Latch(R) 31024767 Luxshare 2H300mmSA T A Cable with Latch(R) 31024785 Grandsun 2H420mmSA T A Cable with Latch(R) 31 ...

  • Lenovo K430 - page 53

    Mechanical JT LX319 K4 chassis card br acket 31500767 JT mobile HDD case 31501000 RoatonK4 Bitland mSA T A Conversion C ard 11200762 JT SSD plastic bracket 31500999 JT M2X3 Dedicated Screw 31501076 N Chassis JT LX-319CT A F ront Bezel 90200579 JT LX-319C T A Upper Bez el with Mode Switch & P ower Botton 90200580 JT LX-319CT A ODD holder 9020058 ...

  • Lenovo K430 - page 54

    Sunre x LXH-EKB-10Y A(SP) B-Silk KB-L VT 25200509 Sunre x LXH-EKB-10Y A(SL) B-Silk KB-L VT 25200510 Sunre x LXH-EKB-10Y A(NL) B-Silk KB-L VT 25200511 Sunre x LXH-EKB-10Y A(IT) B-Silk KB-L VT 25200512 Sunre x LXH-EKB-10Y A(HB) B-Silk KB-L VT 25200513 Sunre x LXH-EKB-10Y A(FR) B-Silk KB-L VT 25200514 Sunre x LXH-EKB-10Y A(BE) B-Silk KB-L VT 25200515 ...

  • Lenovo K430 - page 55

    Liteon SK-8861(IL) S-Silk KB-Black(WW) 90200714 Liteon SK-8861(FR) S-Silk KB-Black(WW) 90200715 Liteon SK-8861(BE) S-Silk KB-Black(WW) 90200716 Liteon SK-8861(GR) S-Silk KB-Black(WW) 90200717 Liteon SK-8861(HU) S-Silk KB-Black(WW) 90200718 Liteon SK-8861(BG) S-Silk KB-Black(WW) 90200719 Liteon SK-8861(KR) S-Silk KB-Black(WW) 90200720 Liteon SK-8861 ...

  • Lenovo K430 - page 56

    50 IdeaCentre K430/K410Hardwar e Maint enance Manual ...

  • Lenovo K430 - page 57

    Chapter 9. Gener al information This chapter provides gener al information that applies to all machine types supported by this publication. Additional Service Information This chapter pr ovides additional information that the service repr esentative might nd helpful. P ower management P ower management reduces the power consumption of certain co ...

Manufacturer Lenovo Category Personal Computer

Documents that we receive from a manufacturer of a Lenovo K430 can be divided into several groups. They are, among others:
- Lenovo technical drawings
- K430 manuals
- Lenovo product data sheets
- information booklets
- or energy labels Lenovo K430
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lenovo K430.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lenovo K430, service manual, brief instructions and user manuals Lenovo K430. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lenovo K430.

Similar manuals

A complete manual for the device Lenovo K430, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lenovo K430 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lenovo K430.

A complete Lenovo manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lenovo K430 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lenovo K430, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lenovo K430, that we can find in the current document
3. Tips how to use the basic functions of the device Lenovo K430 - which should help us in our first steps of using Lenovo K430
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lenovo K430
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lenovo K430 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lenovo K430?

Use the form below

If you did not solve your problem by using a manual Lenovo K430, ask a question using the form below. If a user had a similar problem with Lenovo K430 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)