-
Grizzly H2910 - page 1
COPYRIGHT © JANUARY, 2002 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN 3-IN-1 WOOD, METAL & CONCRETE NAILER MODEL H2910 INSTRUCTION MANUAL ...
-
Grizzly H2910 - page 2
For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a ...
-
Grizzly H2910 - page 3
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -2 - 10. USE PROPER EXTENSION CORD for the tool. Make sure your extension cord is in good condition. Conductor size should be in accordance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss o ...
-
Grizzly H2910 - page 4
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -3 - Operating the nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, the nailer discharges at 85-90 decibels. To protect y ...
-
Grizzly H2910 - page 5
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -4 - INTRODUCTION Commentary Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techs ...
-
Grizzly H2910 - page 6
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the tool at yourself or any bystanders. Serious injury may occur. Exceeding the maximum permissible operating pressure may cause the naile ...
-
Grizzly H2910 - page 7
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -6 - OPERATION Loading The Nailer Depth Adjustment Operating The Nailer To load your nailer: 1. Disconnect the air supply from the nailer! 2. Push the magazine latch in the direc- tion shown in Figure 1 . Figure 1. Releasing magazine latch. Figure 3. Depth adjustment wheel. Figure 2. Loading the nailer ...
-
Grizzly H2910 - page 8
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -7 - To operate your nailer: 1. Connect the air supply to the quick connect fitting. 2. Test the loaded nailer for proper pen- etration. Hold the nailer perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of nails you have loaded. Depress the safety yoke mech ...
-
Grizzly H2910 - page 9
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -8 - Cleaning The Nailer Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nail- er; this may result in leaks and damage to the nailer and the air ...
-
Grizzly H2910 - page 10
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -9 - Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. To replace a piston: Figure 6. Removing the exhaust cap. 8. With a long fla ...
-
Grizzly H2910 - page 11
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -10 - H2910 PART BREAKDOWN 35A 1 2 3 4 6 7 8 9 10 5 11 10 12 13 20 21 22 25 29 26 27 28 23 24 30 31 32 37 39 40 36 41 42 45 57 49 53 43 44 47 48 46 50 51 52 54 59 56 55 14 10 18 19 15 17 16A 21 ...
-
Grizzly H2910 - page 12
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -11 - 01 PH2910001 CAP SCREW 02 PH2910002 CAP COVER 03 PH2910003 SEAL 04 PH2910004 CAP SCREW 05 PH2910005 SETSCREW 06 PH2910006 CAP 07 PH2910007 PISTON STOPPER 08 PH2910008 O-RING 09 PH2910009 COLLAR 10 PH2910010 O-RING 11 PH2910011 SPRING 12 PH2910012 PISTON HEAD VALVE 13 PH2910013 O-RING 14 PH2910014 ...
-
Grizzly H2910 - page 13
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -12 - TROUBLESHOOTING Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips nails while dis- charging. Tool runs slowly or has a loss of power. Fasteners frequently jam the tool. Tool does not fire. 1. O-rings must be repla ...
-
Grizzly H2910 - page 14
H2910 3-IN-1 WOOD, METAL & CONCRETE NAILER -13 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is ...
-
Grizzly H2910 - page 15
Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # ___________________________ Order # _______________________ The following information i ...
-
Grizzly H2910 - page 16
FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT X Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here ...
Do you have a question concerning Grizzly H2910?
Use the form below
If you did not solve your problem by using a manual Grizzly H2910, ask a question using the form below. If a user had a similar problem with Grizzly H2910 it is likely that he will want to share the way to solve it.