English dropdown-ico

Manual Intel ECB-870

115 pages 1.83 mb
Download

Go to site of 115

Summary
  • Intel ECB-870 - page 1

    Part No.2047870000 User’s Manual ECB-870 Intel Pentium 4 Full-size CPU Card w ith Dual 10/100 Base-Tx Ethernet 1 st Ed. – 20 May 2002 ...

  • Intel ECB-870 - page 2

    ECB-870 Evalue Technolog y Inc. FCC STA TEMENT THIS DEVICE COMPLIES W ITH PART 15 FCC RU LES. OPERATION IS SUBJECT TO THE FOLLOW ING TW O CONDIT IONS: (1) THIS DE VICE MAY NOT CAUS E HARMFUL INTERFE RENCE. (2) THIS DEVICE M UST ACCEPT ANY INTERFER ENCE RECEIVED INCL UDING INTERFERENCE T HAT MAY CAUS E UNDESIRED OPERATION. THIS EQUIPMENT HAS BEEN T ...

  • Intel ECB-870 - page 3

    User’s Manual Evalue Technolog y Inc. Copy right Notice Copyr ight  2001, 2002, Ev alue Technology Inc., ALL RIGHTS RESERVED. No part of this document may be repr oduced, copied, translated, or tr ansmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior wr itten permission of the orig inal manufacture ...

  • Intel ECB-870 - page 4

    ECB-870 Evalue Technolog y Inc. A Message to the Customer Evalue C ustomer Serv ices Each and every Evalue’s pr oduct is built to the most ex acting speci fications to ensure reliabl e performance in the harsh and demanding conditions ty pical of industrial envir onments. W hether your new Ev alue devi ce is destined for the labor atory or the fa ...

  • Intel ECB-870 - page 5

    User’s Manual Evalue Technolog y Inc. Product Warranty Evalue warrants to you, the orig inal purchaser, that each of its products will be free from defects in materials and w orkmanship for tw o years from the date of purchase. This war ranty does not appl y to any products w hich hav e been repaired or alter ed by persons other than repai r pers ...

  • Intel ECB-870 - page 6

    ECB-870 Evalue Technolog y Inc. Packing List Before you begin installing y our single board, please make sure that the following materials hav e been shipped:  1 ECB-870 Pentium 4 Ful l-siz e single boar d  1 Quick Installation Gui de  1 CD-R OM contains the follow ings: — User’s Manual (this manual in PDF file) — Ethernet driver and ...

  • Intel ECB-870 - page 7

    User’s Manual Evalue Technolog y Inc. 1. MA NUAL OBJECTIVES .............................................................................................1 2. INTRODUCTION .........................................................................................................2 2.1 Sy stem Ov erview ................................................ ...

  • Intel ECB-870 - page 8

    ECB-870 Evalue Technolog y Inc. 3.9 Setting Jumpers ................................................................................................... 21 3.9.1 COM2 R S-232/422/485 Sel ect (J1, J2, JCSE L) ......................................................... 22 3.9.2 LAN2 Enable / D isable S elect (J82559) .................................... ...

  • Intel ECB-870 - page 9

    User’s Manual Evalue Technolog y Inc. 4.4 In Case of Problems............................................................................................. 46 4.5 Main Menu.............................................................................................................46 4.5.1 Setup Items ............................................... ...

  • Intel ECB-870 - page 10

    ECB-870 Evalue Technolog y Inc. A PPENDIX A : BIOS REVISIONS ......................................................................................87 A PPENDIX B: S YSTEM RESOURCES .............................................................................88 Me mory Ma p ............................................................................ ...

  • Intel ECB-870 - page 11

    User’s Manual Evalue Technolog y Inc. BIOS R OM C hecksu m Error - Sy stem Halted . ........................................................................ 97 Me mory Test Fai l. .............................................................................................................. ..... 97 A P PENDIX D: A WA RD BIOS POST CODES .......... ...

  • Intel ECB-870 - page 12

    ECB-870 Evalue Technolog y Inc. Document A mendment History Revision Date By Comment 1 st May. 2002 Harri s Chen Initial Rel ease ...

  • Intel ECB-870 - page 13

    ECB-870 ECB-870 Us er’s Manual 1 1. Manual Objectives This manual describes i n detail the Ev alue Technology ECB-870 Sing le Board. W e have tried to i nclude as much information as possible but w e hav e not dupl icated information that is prov ided in the standard IBM Technical References, unless it prov ed to be necessary to aid in the unders ...

  • Intel ECB-870 - page 14

    User’s Manual 2 ECB-870 Us er’s Manual 2. Introducti on 2.1 Sy stem Overv iew The ECB-870 is an all -in-one Ful l-siz e Pentium 4 Sing le Board Computer ( SBC) desig ned wi th Intel embedded chipset 845E whi ch supports the latest Intel m- PGA 478 Pentium 4 CPU up to 2.2 GHz + at 400 MHz of FSB, the chipset SiS315 AGP 4X VGA wi th 128/256 bits ...

  • Intel ECB-870 - page 15

    ECB-870 ECB-870 Us er’s Manual 3 2.2 Sy stem Specifications General Functi ons • CPU: Intel Pentium 4 CPU up to 2.2 GHz + at 400 MHz of FSB • CPU Socket: Intel Socket 478 • BIOS: Award 2 M b PnP flash BIOS with APM / AC PI supported • Chipset: Intel 82845 ( MCH) w ith 82801BA (ICH2), ITE 8888 PCI-to- ISA Bridge • I/O Chipset: Intel 8280 ...

  • Intel ECB-870 - page 16

    User’s Manual 4 ECB-870 Us er’s Manual IDE RAID Interface (Optional) • Chipset: Promi se PDC20265R har dware PC I to UltraATA/100 IDE RAID controller • RA ID Level: RAID Level 0 striping and level 1 mi rrori ng • Interface: IDE3/4 dual U ltraATA/100 IDE master interfaces SSD Interface One 32-pin DIP socket suppor ts M-Sys tems DiskOnChip ...

  • Intel ECB-870 - page 17

    ECB-870 ECB-870 Us er’s Manual 5 2.3 A rchitecture Overv iew The following block diagr am shows the archi tecture and main components of ECB-870. Two maj or chipsets on board ar e the 82845 Graph Memory Control Hub and 82801BA ICH2. These two dev ices prov ide interface to Socket478 processor, supports SDRAM with ECC, PCI bus interface, ACPI comp ...

  • Intel ECB-870 - page 18

    User’s Manual 6 ECB-870 Us er’s Manual 2.3.1 82845 MCH and 82801BA The Intel ® 845 chipset is desig ned, val idated, and optimiz ed for the Intel Pentium 4 processor with NetBurst micro-architecture using proven and established building blocks. Intel 845 chipset-based platforms extend the Intel Pentium 4 processor capabilities with a great bal ...

  • Intel ECB-870 - page 19

    ECB-870 ECB-870 Us er’s Manual 7  USB host interface; 2 host controller s and supports 4 USB ports  Integrated LAN contr oller  System Manag ement Bus (SMBus) compati ble wi th most I2C devices; ICH2 has both bus master and slave capability  AC ’97 2.1 compliant l ink for audio and telephony codecs; up to 6 channels (ICH2)  Low P ...

  • Intel ECB-870 - page 20

    User’s Manual 8 ECB-870 Us er’s Manual 2.3.3 A GP Interface A single AGP component or connector (not both) i s supported by the M CH AGP interface. The AGP buff ers operate only i n 1.5 V mode. They are not 3.3 V safe. The AGP interface supports 1x/2x /4x AGP si gnaling and 2x/4x fast w rites. AGP semantic cy cles to system memory ar e not snoo ...

  • Intel ECB-870 - page 21

    ECB-870 ECB-870 Us er’s Manual 9 2.3.6 IDE Interface (Bus Master Capability and Sy nchronous DMA Mode) The fast IDE interface supports up to four IDE devices pr ovidi ng an interface for IDE hard disks and CD ROMs. Each IDE device can hav e independent timings. The IDE interface supports PIO IDE transfers up to 14 Mby tes/sec and Bus Master IDE t ...

  • Intel ECB-870 - page 22

    User’s Manual 10 ECB-870 User ’s Manual 2.3.8.2 Intel 82559 The Ethernet inter face is based on an Intel 82559 Ethernet controll er that supports both 10BASE-T and 100BASE- TX. The 82559 consists of both the Media Access Contr oller (MAC) and the physical l ayer ( PHY) i nterface combined into a singl e component solution. The 32-bit PCI contro ...

  • Intel ECB-870 - page 23

    ECB-870 ECB-870 Us er’s Manual 11 3. Hardw ar e Configurati on This chapter expl ains you the i nstructions of how to set up y our system. The additional information show s y ou how to i nstall M-Sy stems’ DiskOnChip and prog ram the W atchdog Timer . 3.1 Installation Procedure 1. Turn off the power supply . 2. Insert the DIMM modul e ( be car ...

  • Intel ECB-870 - page 24

    User’s Manual 12 ECB-870 User ’s Manual 3.3 Socket 478 Processor 3.3.1 Installing Pentium 4 CPU  Lift the handling lev er of CPU socket outwards and upw ards to the other end.  Align the pr ocessor pins w ith pin holes on the socket. Make sur e that the notched corner or dot mar k (pin 1) of the CPU cor responds to the socket’s bevel en ...

  • Intel ECB-870 - page 25

    ECB-870 ECB-870 Us er’s Manual 13 3.5 M-Sy stems’ DiskOnChip Flash Disk ECB-870 r eserves a 32-pi n DIP socket to support M-Sy stems’ DiskOnC hip flash disk up to 288 MB. The DiskOnChip is based on pure ISA bus and wi thout PnP (Plug and Pl ay) function. Before the installation, make sure that the DiskOnChi p I/O address jumper is set properl ...

  • Intel ECB-870 - page 26

    User’s Manual 14 ECB-870 User ’s Manual 3.6.1 SiS 315 4X A GP VGA Controller W ith a 529-pin PBGA package, Si S315 integrates a 4X /2X AGP controll er wi th full sideband or pipel ine support, a 256-bit 3D /2D graphi cs engine and a motion compensation MPEG I/MPEG II accelerator. It off ers a complete 128-bit SDR/DDR memory data bus. Embedded w ...

  • Intel ECB-870 - page 27

    ECB-870 ECB-870 Us er’s Manual 15 3.6.2 Promise FastTrak100 UltraA TA /100 IDE RA ID Interface (ECB-870R Only ) The board integrates w ith Promise FastTrak100 UltraATA/100 IDE R AID interface that provi des RAID 0 and 1 functions. The function can enable or disable by jumper JRAID and the RAID lev el can be set on BIOS. The channel 1 in BIOS stan ...

  • Intel ECB-870 - page 28

    User’s Manual 16 ECB-870 User ’s Manual 3.6.3 Intel 82559(or 82559ER) & 82801BA (ICH2) + 82562ET ( PHY) Net work Controller The 82559 (or 82559ER) and IC H2+PHY is fully integrated 10BASE- T/100BASE-TX LAN solution. The 32-bit PCI contr oller prov ides enhanced scatter-gather bus masteri ng capabilities and enables the 82559 to perform high ...

  • Intel ECB-870 - page 29

    ECB-870 ECB-870 Us er’s Manual 17 3.7 Watchdog Timer Programming W hen the W atch- D og T imer ( WDT ) function is enabled, a system reset will be generated unless an applicati on trigg ers the timer periodicall y w ithin time- out period. This all ows the system to restar t in an orderly way in case of any abnor mal condition is found. An option ...

  • Intel ECB-870 - page 30

    User’s Manual 18 ECB-870 User ’s Manual 3.8 Jumper & Connector 3.8.1 Jumper & Connector Lay out ...

  • Intel ECB-870 - page 31

    ECB-870 ECB-870 Us er’s Manual 19 3.8.2 Jumper & Connector List Connectors on the board are li nked to external dev ices such as hard disk driv es, keyboard, mouse, or floppy dr ives. In addi tion, the board has a number of jumpers that allow you to configure y our system to sui t your appl ication. The following tables list the function of e ...

  • Intel ECB-870 - page 32

    User’s Manual 20 ECB-870 User ’s Manual Connectors Label Function Note AT X ATX power connector AT X R 1 Pentium IV + 12V connector CHA SFA N System fan connector 3 x 1 w afer, pitch 2.54mm CPUFA N CPU fan connector 3 x 1 w afer, pitch 2.54mm FLOPPY Floppy connector 17 x 2 header, pi tch 2.54mm IDE1 Primar y IDE connector 20 x 2 header, pi tch ...

  • Intel ECB-870 - page 33

    ECB-870 ECB-870 Us er’s Manual 21 3.9 Setting Jumpers You can configure your board to match the needs of your appli cation by setting jumper s. A jumper is the si mplest kind of electric sw itch. It consists of two metal pins and a small metal cl ip (often protected by a pl astic cover) that slides ov er the pins to connect them. To “close” a ...

  • Intel ECB-870 - page 34

    User’s Manual 22 ECB-870 User ’s Manual 3.9.1 COM2 RS-232/422/485 Select ( J1, J2, JCSEL) The ECB-870 COM2 ser ial port can be selected as R S-232, RS-422, or R S-485 by setti ng J1, J2, & JCSEL. COM2 RS-232/422/485 Sel ect (J1, J2, JCSEL) RS-232* RS- 422 RS-485 * default 1 2 3 10 11 12 J2 1 3 5 2 4 6 1 3 5 2 4 6 1 3 5 2 4 6 1 3 2 4 1 3 2 4 ...

  • Intel ECB-870 - page 35

    ECB-870 ECB-870 Us er’s Manual 23 3.9.2 LA N2 Enable / Disable Select (J82559) The primary LAN interface is controll ed by Intel IC H2 with Intel 82562ET and setting as LAN1. It prov ides the same performance as Intel 82559 LAN w ith the same driv er. The OPTIONAL secondary LAN interface is controlled by Intel 82559ER chipset and setting as LAN2. ...

  • Intel ECB-870 - page 36

    User’s Manual 24 ECB-870 User ’s Manual 3.9.5 RA ID Enable / Disable Select ( JRA ID, ECB-870R Only ) The board integrates with Promi se FastTrak100 UltraATA/100 IDE RAID interface that provi des RAID 0 and 1 functions. The function can enable or disable by jumper JRAID and the RAID level can be set on BIOS. The channel 1 in BIOS stands for IDE ...

  • Intel ECB-870 - page 37

    ECB-870 ECB-870 Us er’s Manual 25 3.10 Connector Definitions 3.10.1 A TX Powe r Connector (A TX) Signal PIN Signal +12V 10 20 +12V 5V SB 9 19 5V SB NC 8 18 NC GND 7 17 GND +5V 6 16 +5V GND 5 15 GND +5V 4 14 +5V GND 3 13 GND NC 2 12 NC NC 1 11 NC 3.10.2 Pentium IV +12V Connector (JA TXR1) Signal PIN Signal GND 3 1 GND +12V 4 2 +12V 3.10.3 CPU Fan ...

  • Intel ECB-870 - page 38

    User’s Manual 26 ECB-870 User ’s Manual 3.10.4 Floppy Connector (FLOPPY ) Signal PIN Signal GND 1 2 DRVDEN0# GND 3 4 NC GND 5 6 DRVDEN1# GND 7 8 INDEX# GND 9 10 MOA# GND 11 12 DSB# GND 13 14 DSA# GND 15 16 MOB# GND 17 18 DIR# GND 19 20 STEP# GND 21 22 WD # GND 23 24 WE # GND 25 26 TRAK0# GND 27 28 WP T# GND 29 30 RDATA# GND 31 32 SIDE1# GND 33 ...

  • Intel ECB-870 - page 39

    ECB-870 ECB-870 Us er’s Manual 27 3.10.5 Signal Description – Floppy Connector (FLOPPY ) RDATA# The read data input signal f rom the FDD. W D# W rite data. T his logic low open drain writes pre- compens ation serial data to the selected FDD. An open drain output. W E# W rite enable. An open drain output. MOA# Motor A On. W hen set to 0, this pi ...

  • Intel ECB-870 - page 40

    User’s Manual 28 ECB-870 User ’s Manual 3.10.6 Primary ID E Connector (IDE1) Signal PIN Signal RESET# 1 2 GND PDD7 3 4 PDD8 PDD6 5 6 PDD9 PDD5 7 8 PDD10 PDD4 9 10 PDD11 PDD3 11 12 PDD12 PDD2 13 14 PDD13 PDD1 15 16 PDD14 PDD0 17 18 PDD15 GND 19 20 NC PDDREQ 21 22 GND PDIOW # 23 24 GND PDIOR# 25 26 GND PDIORDY 27 28 GND PDDACK# 29 30 GND IRQ14 31 ...

  • Intel ECB-870 - page 41

    ECB-870 ECB-870 Us er’s Manual 29 3.10.7 Secondary IDE Connector and RA ID IDE Connector (IDE 2, & IDE 3, 4) Signal PIN Signal RESET# 1 2 GND SDD7 3 4 SDD8 SDD6 5 6 SDD9 SDD5 7 8 SDD10 SDD4 9 10 SDD11 SDD3 11 12 SDD12 SDD2 13 14 SDD13 SDD1 15 16 SDD14 SDD0 17 18 SDD15 GND 19 20 NC/ +5V SDDREQ 21 22 GND SDIOW # 23 24 GND SDIOR# 25 26 GND SDIOR ...

  • Intel ECB-870 - page 42

    User’s Manual 30 ECB-870 User ’s Manual 3.10.8 Signal Description – Primary & Secondary and RA ID IDE Connector (IDE 1, 2, 3, 4) PDA [2:0] Primary Disk A dd ress [2:0]. Thes e signals indicate which byte in either the ATA com mand block or control block is being addressed. If the IDE signals are conf igured for Pr imary and Secondary, the ...

  • Intel ECB-870 - page 43

    ECB-870 ECB-870 Us er’s Manual 31 PDIOR# Primary Disk IO Read. In norm al IDE this is the com mand to the IDE devic e that it may drive data onto the PDD [15:0] lines. Data is latched by PIIX4 on the negation edge of PDIOR#. T he IDE device is s elected either by the ATA r egister file chip s elects (PDCS1#, PDCS3#) and the PDA [2:0] lines, or th ...

  • Intel ECB-870 - page 44

    User’s Manual 32 ECB-870 User ’s Manual PDIORDY Primary IO Channel Ready. In normal IDE m ode, this input signal is direc tly driven by the corres ponding IDE device IORDY signal. In an Ultra DMA/33 read cycle, this signal is used as STROBE, with the PIIX4 latc hing data on rising and falling edges of STRO BE. In an Ultra DMA/33 write cy cle, t ...

  • Intel ECB-870 - page 45

    ECB-870 ECB-870 Us er’s Manual 33 SDDACK# S econdary DMA A cknowledge. T his signal directly drives the IDE device DMACK# signal. It is asser ted by PIIX 4 to indicate to IDE DMA slave devices that a given data tr ansfer cycle (asser tion of SDIOR# or SDIOW #) is a DMA data tr ansfer cycle. This s ignal is used in conjunction with the PCI bus m a ...

  • Intel ECB-870 - page 46

    User’s Manual 34 ECB-870 User ’s Manual 3.10.9 Internal Key board Connector (JA TKB) Signal PIN KCLK 1 KDAT 2 NC 3 GND 4 VCC 5 3.10.10 Signal Description – Internal Keyboard Connector (JA TKB) KCLK Bi-directional c lock signal used to s trobe data/com mands f rom/to the PC-AT keyboard. KDAT Bi-directional s erial data line used to transf er d ...

  • Intel ECB-870 - page 47

    ECB-870 ECB-870 Us er’s Manual 35 3.10.12 Fast & Standard IrDA Connector (JIR) Signal PIN PIN Signal +5V 1 6 NC NC 2 7 CIRRX IRRX 3 8 5V Standby GND 4 9 NC IRTX 5 10 NC 3.10.13 Signal Configuration – Fast & Standard IrDA Connector (JIR) IRRX Infr ared Receiver input IRTX Infrared T ransm itter output 3.10.14 Serial Port 1 / 2 Connector ...

  • Intel ECB-870 - page 48

    User’s Manual 36 ECB-870 User ’s Manual 3.10.16 Serial Port 1 / 2 Connector in RS-422 (JC OM1, JCOM2) Signal PIN Signal NC 10 9 RI CTS 8 7 RTS DSR 6 5 GND TxD+ 4 3 TxD- RxD- 2 1 RxD+ 3.10.17 Signal Description – Serial Port 1 / 2 in RS-422 Mode ( JCOM1, JCOM2) Tx D +/- Serial output. This differential s ignal pair sends serial data to the c o ...

  • Intel ECB-870 - page 49

    ECB-870 ECB-870 Us er’s Manual 37 3.10.18 Serial Port 1 / 2 Connector in RS-485 (JC OM1, JCOM2) Signal PIN Signal NC 10 9 CTS/RT S + NC 8 7 CTS/RTS - NC 6 5 GND RxD/Tx D + 4 3 RxD/T xD - NC 2 1 NC 3.10.19 Signal Description – Serial Port 1 / 2 in RS-485 Mode ( JCOM1, JCOM2) RxD/T xD +/- Bi-directional data signal pair. Received data is availabl ...

  • Intel ECB-870 - page 50

    User’s Manual 38 ECB-870 User ’s Manual 3.10.20 A TX Powe r Controller (JPS) Signal PIN 5V Stand-by 1 GND 2 Power On 3 3.10.21 Wake-On-LA N Connector (JWOL) Signal PIN 5V Stand-by 1 GND 2 Power On 3 3.10.22 10/100 BA SE-Tx Ethernet Connector (LA N1, LA N2) Signal PIN TXD+ 1 TXD- 2 RXD+ 3 NC 4 NC 5 RXD- 6 NC 7 NC 8 3.10.23 Signal Description – ...

  • Intel ECB-870 - page 51

    ECB-870 ECB-870 Us er’s Manual 39 3.10.24 Parallel Port Connector (PRINT ER) Signal PIN Signal STB# 1 14 AFD# PD0 2 15 ERR# PD1 3 16 INIT # PD2 4 17 SLIN# PD3 5 18 GND PD4 6 19 GND PD5 7 20 GND PD6 8 21 GND PD7 9 22 GND ACK# 10 23 GND BUSY 11 24 GND PE 12 25 GND SLCT 13 ...

  • Intel ECB-870 - page 52

    User’s Manual 40 ECB-870 User ’s Manual 3.10.25 Signal Description – Parallel Port Connector (PRINTER) The following signal descr iption cover s the signal definit ions, when the parall el port is operated in standard centr onic mode. The parallel por t controller also supports the f ast EPP and ECP modes. Please refer to reference 2 for furt ...

  • Intel ECB-870 - page 53

    ECB-870 ECB-870 Us er’s Manual 41 3.10.26 PS/2 Keyboard C onnector (PS2) Signal PIN Signal NC 6 5 KCLK VCC 4 3 GND NC 2 1 KDAT 3.10.27 PS/2 Mouse Connector (PS2) Signal PIN Signal MCLK 6 5 NC VCC 4 3 GND MDAT 2 1 NC 3.10.28 Signal Description – PS/2 Mouse Connector (PS2) MCLK Bi-directional c lock signal us ed to strobe data/com mands f rom/to ...

  • Intel ECB-870 - page 54

    User’s Manual 42 ECB-870 User ’s Manual 3.10.29 USB Connector (USB A ) Signal PIN CH2 CH1 Signal GND 9 10 GND GND 7 8 GND D1+ 5 6 D2+ D1- 3 4 D2- VCC1 1 2 VCC2 3.10.30 Signal Description – USB Connector (USBA ) D1+ / D1- Dif ferential bi-direc tional data signal for USB channel 0. Cloc k is trans mitted along with the data using NRZI encoding ...

  • Intel ECB-870 - page 55

    ECB-870 ECB-870 Us er’s Manual 43 3.10.31 CRT Connector (VGA ) Signal PIN Signal 6 ANA-G ND RED 1 1 1 NC 7 ANA-G ND GREEN 2 1 2 DDCDAT 8 ANA-G ND BLUE 3 1 3 HSY NC 9 VCC NC 4 1 4 VSYNC 10 DIG-GND DIG-GND 5 1 5 DDCCLK 3.10.32 Signal Description – CRT Connector (VGA ) HSYNC CRT hor iz ontal synchronisation output. VSYNC CRT vertic al sy nchronisa ...

  • Intel ECB-870 - page 56

    User’s Manual 44 ECB-870 User ’s Manual 4. A w ard BIOS Setup 4.1 Starting Setup The AwardBIOS™ i s immediately activ ated when y ou first power on the computer. The BIOS reads the system i nformation contained in the CMOS and beg ins the process of checking out the system and configuring it. W hen it finishes, the BIOS will seek an operating ...

  • Intel ECB-870 - page 57

    ECB-870 ECB-870 Us er’s Manual 45 4.2 Using Setup In general, y ou use the arrow keys to highlig ht items, press < Enter> to select, use the PageUp and PageD own key s to change entries, pr ess <F1> for help and press < Esc> to quit. The follow ing tabl e provi des more detail about how to navi gate in the Setup prog ram using t ...

  • Intel ECB-870 - page 58

    User’s Manual 46 ECB-870 User ’s Manual 4.3 Getting Help Press F1 to pop up a small help w indow that describes the appr opriate keys to use and the possible selections for the highli ghted item. To exi t the Help W indow pr ess <Esc> or the F1 key ag ain. 4.4 In Case of Problems If, after making and saving system chang es with Setup, y o ...

  • Intel ECB-870 - page 59

    ECB-870 ECB-870 Us er’s Manual 47 4.5.1 Setup Items The main menu includes the followi ng mai n setup categories. R ecall that some systems may not incl ude all entries. 4.5.1.1 Standard CMOS Features Use this menu for basic system configurati on. 4.5.1.2 A dvanced B IOS Features Use this menu to set the Adv anced Features av ailable on y our sys ...

  • Intel ECB-870 - page 60

    User’s Manual 48 ECB-870 User ’s Manual 4.5.1.11 Save & Exit Set up Save CM OS value chang es to CMOS and exi t setup. 4.5.1.12 Exit Without Save Abandon all CM OS value chang es and exit setup. 4.5.2 Standard CMOS Setup The items in Standard CM OS Setup Menu are div ided into 10 categor ies. Each category includes no, one or mor e than one ...

  • Intel ECB-870 - page 61

    ECB-870 ECB-870 Us er’s Manual 49 4.5.2.1 Standard CMOS Selection This table show s the selections that you can make on the Standar d CMOS Selection. Item Options Description Da te Mo nth DD YYYY Set the system date. Note that the ‘Day’ automatic ally c hanges when y ou s et the date Tim e HH : MM : SS Set the system tim e IDE Prim ary Master ...

  • Intel ECB-870 - page 62

    User’s Manual 50 ECB-870 User ’s Manual 4.5.2.2 IDE A dapters The IDE adapters control the har d disk driv e. Use a separate sub menu to configur e each hard disk dri ve. Figure 2 show s the IDE primary master sub menu. Use the leg end keys to nav igate thr ough this menu and ex it to the main menu. U se Table 3 to configure the hard di sk. Ite ...

  • Intel ECB-870 - page 63

    ECB-870 ECB-870 Us er’s Manual 51 4.5.3 A dvanced CM OS Setup Defaults This Setup i ncludes all of the adv anced f eatures in the system. The detail descr iptions are specified as below. Figure 3: The A dvanced CMOS Features 4.5.3.1 Virus Warning Allow s y ou to choose the VIRUS W arning feature for IDE Hard Di sk boot sector protection. If this ...

  • Intel ECB-870 - page 64

    User’s Manual 52 ECB-870 User ’s Manual 4.5.3.3 Quick Pow er On Self Test This categ ory speeds up Pow er On Self Test (POST) after y ou power up the computer . If it is set to Enable, BIOS will shorten or skip some check items during POST. Enabled Enable quick POST Disabled Norm al POST 4.5.3.4 First/Second/Third/Other Boot Device The BIOS att ...

  • Intel ECB-870 - page 65

    ECB-870 ECB-870 Us er’s Manual 53 4.5.3.11 Typemat ic Delay (Msec) Sets the delay ti me after the key is hel d down before it beg ins to repeat the keys troke. The choice: 250, 500, 750, and 1000. 4.5.3.12 Security Option Select whether the passwor d is requi red ever y time the system boots or only when you enter setup. Sy stem T he sy stem will ...

  • Intel ECB-870 - page 66

    User’s Manual 54 ECB-870 User ’s Manual 4.5.4 A dvanced Ch ipset Setup Defaults This Setup is very important to keep system’s stability . If you are not technical person, do not attempt to change any parameters. The best way is to choose optimal default setting. Figure 4: The A dvanced Chipset Features This section allow s you to configure th ...

  • Intel ECB-870 - page 67

    ECB-870 ECB-870 Us er’s Manual 55 4.5.4.1 DRA M Timing Selectable If your DIM M memory has SPD (Serial Presence Detect) 8- pin IC on module, you can set this option to “By SPD”. Sy stem will set your SDRAM clock and timing from the SPD IC. If the option set as ”Manual ”, DRAM cl ock and timing must be set from items bel ow: The choice: SP ...

  • Intel ECB-870 - page 68

    User’s Manual 56 ECB-870 User ’s Manual 4.5.4.9 Video BIOS Cacheable Allow s the video BIOS to be cached for faster v ideo performance. The choice: Enable, Disabl e. 4.5.4.10 Video RA M Cacheable Allow s the video R AM to be cached for faster video per formance. The choice: Enable, Disabl e. 4.5.4.11 Memory Hole A t 15M-16M Enabling thi s featu ...

  • Intel ECB-870 - page 69

    ECB-870 ECB-870 Us er’s Manual 57 4.5.5 Integrated Peripherals Setup Defaults This section describes I/O r esources assignment for all of on-boar d peripheral dev ices. Figure 5: The Integrated Peripherals Features 4.5.5.1 On-Chip Primary/Secondary PCI IDE Select “Enabled” to activate each on-boar d IDE channel separately , Select “Disabled ...

  • Intel ECB-870 - page 70

    User’s Manual 58 ECB-870 User ’s Manual 4.5.5.5 USB Keyboard Support This item lets y ou enable or disabl e the USB keyboar d driv er wi thin the onboard BIOS. The choice: Enable, Disabl e. 4.5.5.6 Init Display First Select “AGP” or “PCI Slot” for sy stem to detect first when boot- up. The choice: PCI Slot, AGP. 4.5.5 . 7 IDE HDD Block ...

  • Intel ECB-870 - page 71

    ECB-870 ECB-870 Us er’s Manual 59 4.5.5.9 Onboard FDC Controller Select “Enabled” to activate the on-boar d FDC and “D isabled” to activ ate an add-on FDC. The choice: Disable, Enabl e. 4.5.5.10 Onboard Serial Port 1 & 2 Select an address and corr esponding interr upt for the first/second serial por t. The default value for the first ...

  • Intel ECB-870 - page 72

    User’s Manual 60 ECB-870 User ’s Manual 4.5.5.18 EPP Mode Select Set parallel por t as EPP1.7 or EPP1.9. The choice: EPP1.7, EPP1.9. 4.5.5.19 ECP Mode Use DMA Select a DMA channel i f parallel port i s set as ECP or ECP+ EPP. The choice: 1, 3. 4.5.5.20 PWRON A fter PWR-Fail Select the option for the system acti on after an AC power fail ure. Of ...

  • Intel ECB-870 - page 73

    ECB-870 ECB-870 Us er’s Manual 61 4.5.6 Pow er Management Setup Defaults This APM (Adv anced Power Management) determines how much power energy setting below items to handle system pow er resource can save. The following descriptions w ill specify the definition of each item in detai ls. Figure 6: The Pow er Management Setup 4.5.6.1 A CPI Functio ...

  • Intel ECB-870 - page 74

    User’s Manual 62 ECB-870 User ’s Manual 4.5.6.3 VGA BIOS if S3 Resume W hen select S3 or S1&S3 can convenientl y Enables VGA BIOS, Suspend to R AM function and Power On Suspend function. The choice: Auto, Yes, No. 4.5.6.4 Powe r Management Mini Saving Sy stem starts power s aving function when the inactivity period exceeds 1 hour . Max Savi ...

  • Intel ECB-870 - page 75

    ECB-870 ECB-870 Us er’s Manual 63 4.5.6 . 10 HDD Pow er Dow n This instructs hard dr ives to shut off while i n the Power M anagement modes. 4.5. 6 .11 S o ft-O ff by P W R-BTTN W hen set to “Delay 4 Sec.”, the power button has a dual function where pr essing less than 4 seconds will place the sy stem in sleep mode and shut down the system w ...

  • Intel ECB-870 - page 76

    User’s Manual 64 ECB-870 User ’s Manual 4.5.6.16 USB KB Wake-up From S3 If your USB KB suppor ts PME (Pow er Management Ev ent) sig nal and this item i s set as Enabled, USB KB peri pherals driv e PME sig nal to wake the sy stem f rom low -power states S3. The choice: Disable, Enabl e. 4.5.6.17 Resume by A larm Set this option to enable or disa ...

  • Intel ECB-870 - page 77

    ECB-870 ECB-870 Us er’s Manual 65 4.5.7 PnP/ PCI Setup Defaults This section describes config uring the PCI bus sy stem. PCI (Peripheral Component Interconnect) is a system that allows I/O devi ces to operate at speeds nearing CPU’s when they communicate w ith own speci al components. All of options described i n this section are impor tant and ...

  • Intel ECB-870 - page 78

    User’s Manual 66 ECB-870 User ’s Manual 4.5.7.4 IRQ Resources These options specify the bus that the named interr upt request li nes (IRQs) ar e used on. These options allow you to specify IR Qs for use by legacy ISA adapter cards. These options determine if AMIBIOS should remov e an IRQ f rom the pool of available IR Qs passed to BIOS configur ...

  • Intel ECB-870 - page 79

    ECB-870 ECB-870 Us er’s Manual 67 4.5.8 PC Health Status Set up Defaults This setup describes current CPU surface temperature status detected from hardw are monitor sensor. The status showed on screen will include: 4.5.8.1 CPU Warning Temperature Select to enable or di sable the hardw are monitor sensor and set the warni ng temperature. BIOS Setu ...

  • Intel ECB-870 - page 80

    User’s Manual 68 ECB-870 User ’s Manual 4.5.9.1 Vcore, Vcc3, +5V, +12V, -12V,-5V, VBA T & 5VSB The onboard hardw are monitor i s able to detect the vol tage output by the voltag e regulator s. These values refresh upon any key entry . T he function is optional . 4.5.9.2 Shutdow n Temperature W hen you select “ enabl e “, the CPU w orkin ...

  • Intel ECB-870 - page 81

    ECB-870 ECB-870 Us er’s Manual 69 4.5.9.3 Frequency Control Setup Defaults 4.5.9.4 CPU Clock Ratio The Ratio of some latest Intel Corporati on fixes CPUs and VIA so the R atio cannot be changed w ith the setting. If it di d not fix by C PU manufacturer, it may be changed w ith the setting. Ov er specification oper ations are not recommended. 4.5. ...

  • Intel ECB-870 - page 82

    User’s Manual 70 ECB-870 User ’s Manual 4.5.9.7 CPU Host/3v 66/PCI Clock Choose Default, 100, 103, 105, 107,109,111, 114, 117,120, 127, 130 MHz f or the ex ternal frequency of y our CPU. Y ou can select Default, 66, 69,70,71,73,74,76,78,80,85,87MHz . if your C PU is 100Mhz FSB and select Default, 100, 103, 105, 107,109,111,114,117, 120, 127 or ...

  • Intel ECB-870 - page 83

    ECB-870 ECB-870 Us er’s Manual 71 4.5.12 Set Supervisor/User Password You can assig n, modify, or cancel passw ord setting s. To modify, highli ght “Set Superv isor Password” or “Set User Passw ord” and press the <Enter> key. The screen will prompt y ou (“Enter Passw ord:”). Enter your password. The max imum siz e of the passwor ...

  • Intel ECB-870 - page 84

    User’s Manual 72 ECB-870 User ’s Manual 5. Driver Inst allation 5.1 Driver Installat ion for Ethernet A dapter 5.1.1 Window s 9x The best way to install the dri ver for the Ethernet contr oller is to use the plug and play system of W indows 9x. The following procedures illustrate how the installation can be done. 1. If a dri ver for the Etherne ...

  • Intel ECB-870 - page 85

    ECB-870 ECB-870 Us er’s Manual 73 • If the ‘ Network adapter s ’ line is present, expand the l ine and remov e the PCI Ethernet Adapter. This is done by selecting the line and clicki ng the ‘ Remove ’ button. Before removal of the adapter( s), your screen mig ht look like this : • W hen all adapters are r emoved (or none were pr esent ...

  • Intel ECB-870 - page 86

    User’s Manual 74 ECB-870 User ’s Manual 4. Click the ‘ Next ’ button to conti nue the driver installation. 5. Specify the location of netw ork adapter and cli ck ‘ Next ’ (see below ). ...

  • Intel ECB-870 - page 87

    ECB-870 ECB-870 Us er’s Manual 75 6. Click the ‘ Next ’ button to i nstall the networ k adapter driv er. 7. Click the ‘ Next ’ button. ...

  • Intel ECB-870 - page 88

    User’s Manual 76 ECB-870 User ’s Manual 8. Click the ‘ Finish ’ button. 9. To complete the instal lation, reboot the computer by clicking the ‘ Yes ’ button in the wi ndow show n below. 10.After the sy stem restar ts, the network adapter should be installed. Pr otocols, clients etc. may now be instal led for the networ k in use. Further ...

  • Intel ECB-870 - page 89

    ECB-870 ECB-870 Us er’s Manual 77 5.1.2 Window s NT 4.0 Ethernet Installation A driver f or the Intel 82559 Ethernet controller on board is incl uded in the attached supporting CD-ROM. The dri ver for this adapter is denoted ‘Intel ® PRO Adapter’. This driv er may be i nstalled in tw o way s: • During the install ation process w here the n ...

  • Intel ECB-870 - page 90

    User’s Manual 78 ECB-870 User ’s Manual 2. Double cl ick the ‘ Network ’ icon and click the ‘ Adapters ’ tab on the follow ing w indow . A wi ndow as the one show n below shoul d now appear . 3. Click the ‘ Add... ’ button, and the followi ng wi ndow should appear . ...

  • Intel ECB-870 - page 91

    ECB-870 ECB-870 Us er’s Manual 79 4. Click the ‘ Have Disk… ’ button to install the Netw ork adapter dr iver from CD-ROM . A wi ndow as the one show n below shoul d now appear . 5. Locate the path of Network adapter driv er and click the ‘ OK ’ button. ...

  • Intel ECB-870 - page 92

    User’s Manual 80 ECB-870 User ’s Manual 6. Select the ‘ Intel® PRO Adapter ’ from the list (as show n below ) and click the ‘ OK ’ button. The Network adapter driv er should now be installed. 7. After the dr iver installation i s complete, Protocols, Ser vices etc. may now be config ured for the network to be used. An example is shown ...

  • Intel ECB-870 - page 93

    ECB-870 ECB-870 Us er’s Manual 81 8. Click ‘ Clo se ’ to accept the setting s. 9. IP Address, DNS etc. may now be configur ed for the network to be used. C lick ‘ OK ’ to accept the settings. 10.To complete the driv er installati on, reboot the computer by clicking the ‘ Yes ’ button in the wi ndow show n below. ...

  • Intel ECB-870 - page 94

    User’s Manual 82 ECB-870 User ’s Manual 5.2 Driver Installat ion for Display Ad apter 5.2.1 Window s 9x The f ollowing steps will install the d isp la y driv er fo r the ‘SiS315 ’ d isplay controller. 1. Find the director y of the driv er disk w ith SiS315 VGA driv er. Double click the icon ‘315w98me’ on the folder. This should start th ...

  • Intel ECB-870 - page 95

    ECB-870 ECB-870 Us er’s Manual 83 3. Click the ‘ Next ’ to conti nue the driver install. If you w ant to stop the installation, click the ‘ Cancel ’. 4. Choose to click the ‘Typi cal ’ / ‘Compact’/ ‘C ustom’ to install the displ ay driv er. If y ou want to chang e the default destination directory , click the ‘Browse’ . ...

  • Intel ECB-870 - page 96

    User’s Manual 84 ECB-870 User ’s Manual 5. Click the ‘ Next ’ to conti nue the display dr iver installation. 6. Click the ‘ Next ’ to continue the display driv er installation. The driver files w ill now be read and the display adapter is show n as the fo llow ing. Click the ‘ Next ’ button to install the display driv er. ...

  • Intel ECB-870 - page 97

    ECB-870 ECB-870 Us er’s Manual 85 7. T o complete the displ ay dri ver instal lation, reboot the computer by clicking the ‘ Yes ’ button in the wi ndow show n below . 8. Further configurati on of the display adapter may be made f rom the ‘ Displ ay Properties ’ wi ndow (follow step 1 above). The ‘ Settings ’ tab al lows y ou to change ...

  • Intel ECB-870 - page 98

    User’s Manual 86 ECB-870 User ’s Manual 9. The ‘Information’ tab allow s you to g et the information for SiS315 display controller. ...

  • Intel ECB-870 - page 99

    ECB-870 ECB-870 Us er’s Manual 87 A ppendi x A : BIOS Revisions BIOS Rev. New Features Bugs/Problems Solved Know n Problems ...

  • Intel ECB-870 - page 100

    User’s Manual 88 ECB-870 User ’s Manual A ppendix B: Sy stem Resources Memory Map The following table indicates memor y map of ECB-870. The address ranges specify the runtime code leng th. A ddress Range Description Note 000A0000h-000BFFFFh PCI bus 000A0000h-000BFFFFh Intel(R) 845 Chipset Process or to AGP Control l er - 1A31 000A0000h-000BFFFF ...

  • Intel ECB-870 - page 101

    ECB-870 ECB-870 Us er’s Manual 89 I/O – Map Certain I/O addr esses are subject to change dur ing boot as PnP managers may relocate devices or functions. The addresses shown in the table ar e typical locations. I/O Port Description Note 0022h-003Fh PCI bus 0044h-0047h PCI bus 004Ch-006Fh PCI bus 0072h-007Fh PCI bus 0090h-0091h PCI bus 0093h-009F ...

  • Intel ECB-870 - page 102

    User’s Manual 90 ECB-870 User ’s Manual I/O Port Description Note 0000h-000Fh Dir ect mem ory access controller 0081h-0083h Direct mem ory access controller 0087h-0087h Direct mem ory access controller 0089h-008Bh Direct m emory access c ontroller 008Fh-0091h Dir ect mem ory access controller 00C0h-00DFh Direct m emor y acc ess controller 0060h ...

  • Intel ECB-870 - page 103

    ECB-870 ECB-870 Us er’s Manual 91 Interrupt Usage. The onboard Intel 82801BA prov ides an ISA compatible inter rupt controller with functionality as tw o 8259A interrupt controllers . The two controller s are cascaded to provi de 13 external interrupts. The actual interrupt setti ngs depend on the PnP handler, the table below indicates the typica ...

  • Intel ECB-870 - page 104

    User’s Manual 92 ECB-870 User ’s Manual DMA -channel Usage The DMA circuitr y incorporates the functionality of two 8237 DMA contr ollers w ith sev en progr ammable channels. The controller s are referenced DM A Controller 1 for channels 0- 3 and D MA Contr oller 2 for channels 4-7. Channel 4 i s by default used to cascade the tw o contro llers ...

  • Intel ECB-870 - page 105

    ECB-870 ECB-870 Us er’s Manual 93 A ppendix C: A W A RD BIOS POST M essages During the Power On Sel f-Test (POST), if the BIOS detects an error req uiring y ou to do something to fix, it will either sound a beep code or display a m essage. If a message is displayed, it will be accompanied by: PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER SET ...

  • Intel ECB-870 - page 106

    User’s Manual 94 ECB-870 User ’s Manual Display Ty pe Has Changed Since Last Boot Since last pow ering off the system, the displ ay adapter has been changed. You must configure the sy stem for the new display type. EISA Configuration Checksum Error Please Run EISA Configuration Utility The EISA non-volatile RAM checksum is incorrect or cannot c ...

  • Intel ECB-870 - page 107

    ECB-870 ECB-870 Us er’s Manual 95 Key board Error Or No Key board Present Cannot initi alize the key board. Make sure the keyboard is attached correctly and no keys are being pressed during the boot. If you are purposel y configuri ng the system w ithout a keyboard, set the error halt condition in Setup to HALT ON ALL, B UT KEYBOARD. This will ca ...

  • Intel ECB-870 - page 108

    User’s Manual 96 ECB-870 User ’s Manual RA M Parity Error – Checking For Segment... Indicates a parity error i n Random Access Memory . Should Be Empty But EISA Board Found Please Run EISA Configuration Utility A vali d board ID w as found in a slot that was configured as hav ing no board ID. NOT E; W hen this error appear s, the system will ...

  • Intel ECB-870 - page 109

    ECB-870 ECB-870 Us er’s Manual 97 Hard Disk(s) Fail ( 10) → → → → Unable To Recalibrate Fixed Disk. Hard Disk(s) Fail ( 08) → → → → Sector Verify Failed. Key board Is Locked Out - Unlock The K ey . BIOS detect the keyboard i s locked. P17 of keyboard contr oller is pul led low . Key board Error Or No Key board Present. Cannot init ...

  • Intel ECB-870 - page 110

    User’s Manual 98 ECB-870 User ’s Manual A ppendi x D: A W ARD BIOS POST Codes POST Code (hex) Description CFh T est CMOS R/W f unctionality . C0h Early chipset initialization: -Disable shadow RAM -Disable L2 cac he (sock et 7 or below) -Program basic chips et registers C1h Detec t memory -Auto-detection of DRAM siz e, ty pe and ECC. -Auto-detec ...

  • Intel ECB-870 - page 111

    ECB-870 ECB-870 Us er’s Manual 99 POST Code (hex) Description 12h Use walking 1’s algorithm to check out interfac e in CMOS circuitr y . Als o set real-tim e clock power status , and then check for override. 13h Reserved 14h Program chipset default values into c hipset. Chipset default values are MODBINable by OEM custom ers. 15h Reserved 16h I ...

  • Intel ECB-870 - page 112

    User’s Manual 100 ECB-870 User ’s Manual POST Code (hex) Description 28h Reserved 29h 1. Pr ogram CPU internal MT RR (P6 & PII) for 0- 640K mem ory address. 2. Initialize the APIC for Pentium class CPU. 3. Program early c hipset according to CMOS setup. Ex ample: onboard ID E control ler. 4. Meas ure CPU speed. 5. Invok e video BIOS. 2Ah Re ...

  • Intel ECB-870 - page 113

    ECB-870 ECB-870 Us er’s Manual 101 POST Code (hex) Description 49h 1. Calculate total mem ory by tes ting the last double word of each 64K page. 2. Pr ogram writes alloc ation for AMD K5 CPU. 4Ah Reserved 4Bh Reserved 4Ch Res erved 4Dh Res erved 4Eh 1. Pr ogram MT RR of M1 CPU 2. Initialize L2 cache f or P6 class CPU & progr am CPU with prope ...

  • Intel ECB-870 - page 114

    User’s Manual 102 ECB-870 User ’s Manual POST Code (hex) Description 66h Reserved 67h Prepare m emory size information f or function c all: INT 15h ax =E820h 68h Reserved 69h Turn on L2 cac he 6Ah Reserved 6Bh Program chipset regis ters according to item s desc ribed in Setup & Auto-conf iguration table. 6Ch Res erved 6Dh 1. Assign resour c ...

  • Intel ECB-870 - page 115

    ECB-870 ECB-870 Us er’s Manual 103 POST Code (hex) Description 82h 1. Call chipset power m anagement hook . 2. Rec over the text fond used by EPA logo (not for f ull screen logo) 3. If password is set, as k for pas sword. 83h Save all data in stack back to CMOS 84h Initialize ISA PnP boot devices 85h 1. USB f inal Initializ ation 2. NET PC: Build ...

Manufacturer Intel Category Personal Computer

Documents that we receive from a manufacturer of a Intel ECB-870 can be divided into several groups. They are, among others:
- Intel technical drawings
- ECB-870 manuals
- Intel product data sheets
- information booklets
- or energy labels Intel ECB-870
All of them are important, but the most important information from the point of view of use of the device are in the user manual Intel ECB-870.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Intel ECB-870, service manual, brief instructions and user manuals Intel ECB-870. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Intel ECB-870.

Similar manuals

A complete manual for the device Intel ECB-870, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Intel ECB-870 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Intel ECB-870.

A complete Intel manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Intel ECB-870 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Intel ECB-870, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Intel ECB-870, that we can find in the current document
3. Tips how to use the basic functions of the device Intel ECB-870 - which should help us in our first steps of using Intel ECB-870
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Intel ECB-870
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Intel ECB-870 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Intel ECB-870?

Use the form below

If you did not solve your problem by using a manual Intel ECB-870, ask a question using the form below. If a user had a similar problem with Intel ECB-870 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)