English dropdown-ico

Manual Zenoah KAM-402

20 pages 0.73 mb
Download

Go to site of 20

Summary
  • Zenoah KAM-402 - page 1

    KAM-402 BRUSHCUTTERS 115 39 34-38 (009) OWNER’S MANUAL •B efore using our brushcutter, please read this manual carefully to understand the proper use of your unit. • Keep this manual handy. Caution ...

  • Zenoah KAM-402 - page 2

    2 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ NOTES ON TYPES OF WARNINGS IN THE MANUAL T ...

  • Zenoah KAM-402 - page 3

    3 1. W arning labels on the machine (1) Read owner’s manual before operating this machine. (2) Wear head, eye and ear protection. (3) Wear foot protection. (4) Wear gloves. (5) Beware of thrown objects. (6) Warning / Attention (7) Keep all children, bystanders and helpers 15 meters away from the machine. If warning label peels off or becomes soil ...

  • Zenoah KAM-402 - page 4

    4 For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: AIR CLE ...

  • Zenoah KAM-402 - page 5

    5 2. Never use the product, (1) When the ground is slippery or when you can’t maintain a steady posture. (2) At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. (3) During rain storms, during lightning storms, at times of strong or ga ...

  • Zenoah KAM-402 - page 6

    6 to sound level and hours of operations for the product. ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 15 m of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be p ...

  • Zenoah KAM-402 - page 7

    7 serious burns or electrical shock. ■ IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine befor ...

  • Zenoah KAM-402 - page 8

    8 This contact causes the blade to stop for an instant and then suddenly move or ”bounce” away from the object that was hit. The operator can lose control of the unit and the blade can cause serious personal injury to the operator or any person nearby if the blade contacts any part of the body. 2. How you can reduce the chance of blade thrust: ...

  • Zenoah KAM-402 - page 9

    9 ■ CONNECTING SWITCH WIRES • Connect the switch wires between the engine and the main unit. ■ INSTALLING DEBRIS GUARD 1. Fit the guard skirt on debris guard. 2. Attach the debris guard with the bolts provided to the pipe. ■ INSTALLING LINE HEAD 1. While locking the gear shaft by inserting the hexagonal bar into the holder A on the gear box ...

  • Zenoah KAM-402 - page 10

    10 ■ INSTALLING BLADE Remove the guard skirt of debris guard, when using metal blade. 1. Put the hexagonal bar into the side holes of the holder A and the gearcase. 2. Remove the nut(Left-handed) and the holder B from the gearshaft. 3. Put the blade onto the holder A. Make the marked side face the holder. 4. Put the holder B onto the gearshaft ma ...

  • Zenoah KAM-402 - page 11

    11 6. Fuel • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. •W ipe up all spills before starting the engine. • Make sure to stop the engine and allow it cool before refueling the unit. • Keep open flames away from the area where fuel is handled or stored. • Never use oil for 4 cycle engine use or wate ...

  • Zenoah KAM-402 - page 12

    12 5. Set the stop switch to the “RUN” position. Place the unit on a flat, firm place. Keep the cutting head clear of everything around it. (1) Stop switch 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to rotat ...

  • Zenoah KAM-402 - page 13

    13 2. When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter- clockwise. (1) Idle adjusting screw Warm up the engine before adjusting the idling speed. ■ CUTTING WORK • By using the shoulder strap, hang the unit on your right side. Adjust the strap length so that the cutting head may become parallel t ...

  • Zenoah KAM-402 - page 14

    14 eyes and face and cause serious personal injury. 2. Keep the debris guard attached in place at all times when the unit is operated. TRIMMING GRASS AND WEEDS • Always remember that the TIP of the line does cutting. You will achieve better results by not crowding the line into the cutting area. Allow the unit to trim at its own pace. 1. Hold the ...

  • Zenoah KAM-402 - page 15

    15 • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged. • To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. Tightning torque: 9.8~11.8N.m. (1.0~1.2kgm)) ? ...

  • Zenoah KAM-402 - page 16

    16 8. Maintenance could cause the engine to catch on fire. Always make sure that the muffler is clean and free of wood chips, leaves, and other waste before use. • Check the intake air cooling vent and the area around the cylinder cooling fins after every 25 hours of use for blockage, and remove any waste which has attached itself to the brushcut ...

  • Zenoah KAM-402 - page 17

    17 9. T rouble shooting 10. Disposal • When the symptoms in the left column do not improve after taking the measures in the right column, please contact the shop where you bought this product. • For the measures marked with ✩ , please buy ZENOAH’ s genuine parts at the shop where you bought this product. PHENOMENON The engine does not start ...

  • Zenoah KAM-402 - page 18

    18 Should any failure occur on the product under normal operating conditions within the applicable warranty period, the failed part will be replaced or repaired free of charge by a ZENOAH authorized dealer. WARRANTY PERIOD: Six (6) months after purchased by end-user subject to 12 months from produced month. (30 days if used for rental purpose) THE ...

  • Zenoah KAM-402 - page 19

    ...

  • Zenoah KAM-402 - page 20

    1-9, Minamidai, Kawagoe-city , Saitama, 350-1 165 Japan To Dealer: Please complete the following form at time of sale. Product Model: KAM-402 Date of Purchase: D / M / Y Purchaser: Dealer: Name: Name: Address/Phone: Address/Phone: Equipment No.: Engine No.: Use: Private Professional Rental To Purchaser: When your unit requires any repair , please b ...

Manufacturer Zenoah Category Trimmer

Documents that we receive from a manufacturer of a Zenoah KAM-402 can be divided into several groups. They are, among others:
- Zenoah technical drawings
- KAM-402 manuals
- Zenoah product data sheets
- information booklets
- or energy labels Zenoah KAM-402
All of them are important, but the most important information from the point of view of use of the device are in the user manual Zenoah KAM-402.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Zenoah KAM-402, service manual, brief instructions and user manuals Zenoah KAM-402. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Zenoah KAM-402.

Similar manuals

A complete manual for the device Zenoah KAM-402, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Zenoah KAM-402 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Zenoah KAM-402.

A complete Zenoah manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Zenoah KAM-402 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Zenoah KAM-402, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Zenoah KAM-402, that we can find in the current document
3. Tips how to use the basic functions of the device Zenoah KAM-402 - which should help us in our first steps of using Zenoah KAM-402
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Zenoah KAM-402
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Zenoah KAM-402 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Zenoah KAM-402?

Use the form below

If you did not solve your problem by using a manual Zenoah KAM-402, ask a question using the form below. If a user had a similar problem with Zenoah KAM-402 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)