English dropdown-ico

Manual Exmark VT691KA484CA

60 pages 4.71 mb
Download

Go to site of 60

Summary
  • Exmark VT691KA484CA - page 1

    V ANT AGE For Serial Nos. 312,000,000 & Higher Part No. 4501-211 Rev . A ...

  • Exmark VT691KA484CA - page 2

    W ARNING CALIFORNIA Proposition 65 W ar ning The engine exhaust from this product contains chemicals known to the State of Califor nia to cause cancer , bir th defects, or other reproductiv e har m. Important: The engine in this product is not equipped with a spark arr ester mufer . It is a violation of Califor nia Public Resource Code (CPRC) Se ...

  • Exmark VT691KA484CA - page 3

    Introduction CONGRATULATIONS on the purchase of your Exmark Mo wer . This product has been carefully designed and manufactured to giv e you a maximum amount of dependability and years of trouble-free operation. This manual contains operating, maintenance, adjustment, and safety instr uctions for y our Exmark mow er . BEFORE OPERATING Y OUR MO WER, ...

  • Exmark VT691KA484CA - page 4

    Contents Introduction . .. . . .. . . . .. . . .. . . . .. . . .. . . . .. . . .. . . . .. . . .. . . .. . . . .. . . .. . . . 3 Safety .. . . . .. . . .. . . . .. . . .. . . . .. . . .. . . .. . . . .. . . .. . . . .. . . .. . . . .. . . .. . . . .. . . .. 5 Safety Alert Symbol . . .. . . .. . . . .. . . .. . . .. . . . .. . . .. . . . .. . . .. . ...

  • Exmark VT691KA484CA - page 5

    Safety Safety Safety Alert Symbol This lawn mow er meets or ex ceeds the B71.4 specications of the American National Standards Institute in effect at the time of production. Exmark designed and tested this lawn mo wer to offer reasonably safe ser vice; how ev er , failure to comply with the following instr uctions ma y result in personal injur y ...

  • Exmark VT691KA484CA - page 6

    Safety • Inspect the area where the equipment is to be used and remov e all rocks , to ys , stic ks , wires , bones , and other foreign objects whic h can be thrown b y the machine and ma y cause personal injur y to the operator or bystanders . DANGER In cer tain conditions gasoline is extremely ammable and v apors are explosi ve. A re or e ...

  • Exmark VT691KA484CA - page 7

    Safety Operation W ARNING Operating engine par ts, especially the mufer , become extremely hot. Sev ere bur ns can occur on contact and de bris, such as leav es, grass, br ush, etc. can catch re. • Allow engine parts, especially the muf er , to cool before touching . • Remo ve accumulated debris from muf er and engine area. • Inst ...

  • Exmark VT691KA484CA - page 8

    Safety DANGER Operating on wet g rass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator's footing could result in a fall with an ar m or leg getting under the mow er or engine deck which may result in serious injur y , death or drowning . • Mow across slopes, nev er up and down. • Do Not mo w sl ...

  • Exmark VT691KA484CA - page 9

    Safety DANGER Batter y electrolyte contains sulfuric acid, which is poisonous and can cause sev ere bur ns. Swallo wing electrolyte can be fatal or if it touches skin can cause severe bur ns. • W ear safety glasses to shield eyes, and r ub ber glo ves to protect skin and clothing when handling electrolyte. • Do Not s w allo w electrolyte. • I ...

  • Exmark VT691KA484CA - page 10

    Safety Safety and Instructional Decals • Keep all safety signs legible. R emo v e all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damaged, or missing safety signs . • When replacement components are installed, be sure that cur rent safety signs are afx ed to the replaced components . • If a ...

  • Exmark VT691KA484CA - page 11

    Safety 1 16-0404 1 16-2040 1 16-3076 60 Inch Model 1 16-3267 1 16-3283 1 16-3290 1 16-4181 1 1 ...

  • Exmark VT691KA484CA - page 12

    Safety 1 16-5040 1. Forward position – faster 2. Backward position – slower 1 16-7217 1 16-1887 1. Fast 3. Neutral 2. Slow 4. Reverse 1 16-4647 12 ...

  • Exmark VT691KA484CA - page 13

    Safety 1 16-4648 All Units Except EFI 1. PTO-on 4. Slow 2. PTO-of f 5. Choke-on 3. Fast 6. Choke-off 1 16-5026 EFI Only 1. PTO-on 3. Fast 2. PTO-of f 4. Slow 13 ...

  • Exmark VT691KA484CA - page 14

    Specications Specications Model Numbers Serial Nos: 312,000,000 and Higher VT651KA484; VT691KA484CA; VT691KA524; VT691KA524CA; VT730EKC524; VT740EKC604; Systems Engine • Engine Specications: See your Engine Owner’ s Manual • Engine Oil T ype: Exmark 4–Cycle Premium Engine Oil • RPM: Full Speed: 3600 ±100 RPM (No Load) Fuel Syste ...

  • Exmark VT691KA484CA - page 15

    Specications T ransmission • T w o Hydro Gear v ariable displacement high efciency pumps independently coupled to tw o high efciency P arker/R oss wheel dri ve motors . • Hydraulic Oil: Use Exmark Premium Hydro Oil. • Hydraulic Oil Capacity: 2.4 qt. (2.2 L) • Hydraulic Filter is replaceable cartridg e type . P/N 109-4180: 25 micron ...

  • Exmark VT691KA484CA - page 16

    Product Overview T read W idth: (Outside to Outside of Tires, W idthwise) 48 inch Deck 52 inch Deck 60 inch Deck 46.5 inches (118.1 cm) 46.5 inches (118.1 cm) 50.5 inches (128.3 cm) Curb Weight: 48 inch Deck 52 inch Deck 60 inch Deck 855 lb (388 kg) 875 lb (397 kg) 883 lb (401 kg) Note: W eights will v ar y slightly depending on engine . T orque Re ...

  • Exmark VT691KA484CA - page 17

    Operation Operation Note: Deter mine the left and right sides of the machine from the normal operating position. Controls Motion Control Levers The motion control levers , located on eac h side of the top console , control the forw ard and rev erse motion of the mac hine. Moving the lev ers forward or backw ard turns the wheel on the same side forw ...

  • Exmark VT691KA484CA - page 18

    Operation Park Brake Lever Located on left side of unit, just to the front of the LH motion control lev er (see Figure 5). The brake lev er engag es a parking brake on the dri v e wheels . Note: The LCD indicator appears in the message display on the front console when the park brak e is engag ed (see Figure 5 and Figure 7). T o engage the brake , ...

  • Exmark VT691KA484CA - page 19

    Operation Fuel Gauge Located on the top left side of the tank (see Figure 5). The fuel g auge monitors the amount of fuel in the tank. Drive Wheel Release V alves Located on the right front corner of the h ydrostatic pumps . Driv e wheel release v alv es are used to release the hy drostatic dri v e system to allow the machine to be mov ed by hand w ...

  • Exmark VT691KA484CA - page 20

    Operation 3. Push in (down) on the PTO switch to the “disengag e” position. 4. Place the throttle midw ay between the “SLO W” and “F AST” positions . 5. On a cold engine, push the chok e lev er forward into the “ON” position (ex cept Kohler EFI units). On a w ar m engine, lea ve the c hoke in the “OFF” position. 6. T urn ignitio ...

  • Exmark VT691KA484CA - page 21

    Operation Driving the Machine CAUTION Machine can spin ver y rapidly by positioning one lever too much ahead of the other . Operator may lose control of the machine, which may cause damage to the machine or injur y . • Use caution when making tur ns. • Slow the machine down before making shar p tur ns. Important: T o begin mov ement (forw ard o ...

  • Exmark VT691KA484CA - page 22

    Operation Figure 10 T o turn left or right, release pressure on the motion control lever tow ard the desired turn direction. 3. T o stop , position both motion control lev ers in the neutral operate position. Adjusting the Front Reference/Speed Control Bar Adjust the front reference/speed control bar for desired maximum forward speed. 1. Stop the m ...

  • Exmark VT691KA484CA - page 23

    Operation W ARNING The operator platfor m is heavy and may cause injur y when lowering and raising the operator platfor m. The platfor m may suddenly drop if not suppor ted when the latch pin is pulled out. • Do Not put y our hands or ngers in the platfor m piv ot area when lowering or raising the operator platfor m. • Make sure the platfor ...

  • Exmark VT691KA484CA - page 24

    Operation Adjusting the Cutting Height The cutting height of the mo wer deck is adjusted from 1 to 5 inches (2.5 cm to 12.7 cm) in 1/4 inch (6.4 mm) increments . 1. Stop the mac hine and mov e the motion control levers to the neutral position. 2. Disengag e the PTO . 3. Raise and loc k the deck to the 5 inc h (12.7 cm) transport position. The deck ...

  • Exmark VT691KA484CA - page 25

    Operation W ARNING Loading a unit on a trailer or tr uck increases the possibility of backw ard tip-ov er . Backw ard tip-ov er could cause serious injur y or death. • Use extreme caution when operating a unit on a ramp. • Use only a single, full width ramp; Do Not use individual ramps for each side of the unit. • If indi vidual ramps must be ...

  • Exmark VT691KA484CA - page 26

    Maintenance Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystander s. Remo ve the k ey from the ignition switch, engage parki ...

  • Exmark VT691KA484CA - page 27

    Maintenance Maintenance Ser vice Inter v al Maintenance Procedure Every 500 hours • R eplace the secondary air cleaner element. (Ma y need more often under sev ere conditions . See the Engine manual for additional infor mation.) • Change the h y draulic lter and uid (Ev er y 250 hours/yearly if using Mobil 1 15W50) • Chec k the wheel hu ...

  • Exmark VT691KA484CA - page 28

    Maintenance V oltage Reading Percent Charge Maximum Charger Settings Charging Inter v al 12.0–12.2 25–50% 14.4 v olts/4 amps 2 Hours 11.7–12.0 0–25% 14.4 volts/4 amps 3 Hours 11.7 or less 0% 14.4 volts/2 amps 6 Hours or More Important: F or Kohler EFI units: Unplug the har ness from the ECU before perfor ming any welding on the equipment. R ...

  • Exmark VT691KA484CA - page 29

    Maintenance Figure 16 1. Positive (+) cable on discharged battery 2. Positive (+) cable on booster battery 3. Negative (–) cable on the booster battery 4. Negative (–) cable on the engine block 5. Booster battery 6. Discharged battery 7. Engine block 4. Connect the other end of the positiv e cable to the positiv e ter minal of the booster batte ...

  • Exmark VT691KA484CA - page 30

    Maintenance A. Install bushing through blade with bushing ange on bottom (grass) side of blade. Figure 18 1. Install bushing in blade prior to installing bushing in spindle. B . Install bushing/blade assembly into spindle . Figure 19 1. Use wrench here for blade installation. This nut has been torqued to 130-160 ft-lb (176–217 N-m) 2. T orque ...

  • Exmark VT691KA484CA - page 31

    Maintenance 5. Mov e the right side motion control lev er to the center , operating position. 6. Continue holding the right side motion control lever in the center , operating position and pull up on the blade control switch (PTO) and release. The clutch should engage and the mower blades begin rotating . 7. Mov e or release the right side motion c ...

  • Exmark VT691KA484CA - page 32

    Maintenance 1. Stop engine and w ait for all moving parts to stop , and remo v e k ey . Engage parking brak e . 2. Clean area around h ydraulic reser v oir cap and remov e cap . Oil lev el should be to the top of the bafe inside the tank. If not, add oil. Use Exmark Premium Hy dro Oil. Replace hy draulic reser voir cap and tighten until snug . D ...

  • Exmark VT691KA484CA - page 33

    Maintenance Figure 20 1. Seal guard 2. Spacer nut with wrench ats 2. R emov e caster wheel from caster forks . 3. R emov e seal guards from the wheel hub . 4. R emov e one of the spacer nuts from the axle assembly in the caster wheel. Note that thread locking adhesiv e has been applied to lock the spacer nuts to the axle . R emov e the axle (wit ...

  • Exmark VT691KA484CA - page 34

    Maintenance Every 500 hours/Y early (whichever comes rst) thereafter (Every 250 hours/Y early if using Mobil 1 15W50) Note: Use only Exmark P art No . 109–4180 for Summer use abo ve 32°F (0°C) or P/N 1-523541 for Winter use below 32°F (0°C) (R efer to T ransmission section in Specications for lter specications). 1. Stop engine, w ...

  • Exmark VT691KA484CA - page 35

    Maintenance Figure 21 1. Charge pump cap 2. Loosen 1 1/2 turns only 1. Stop engine and w ait for all moving parts to stop . Raise the rear of the machine up onto jack stands high enough to raise the dri v e wheels off the g round. 2. Check oil lev el as stated in Check Hydraulic Oil Level section. 3. Start engine and mov e throttle control ahead to ...

  • Exmark VT691KA484CA - page 36

    Maintenance Thread Locking Adhesives Thread loc king adhesi ves such as “Loctite 242” or “F el-Pro , Pro-Loc k Nut T ype” are used on the following fasteners: • Pump sheav e setscrews . • Sheav e retaining bolt in end of engine crankshaft. • Caster wheel spacer nuts . • Platfor m spring pin. Mobil HTS Grease (Or Food-Grade Anti-seiz ...

  • Exmark VT691KA484CA - page 37

    Maintenance Figure 22 1. Blades front to rear 2. Measure here 7. Measure between the outside cutting edges and the at surface ( Figure 23). If both measurements are not within 3/16 inc h (5 mm), an adjustment is required; contact an Authorized Ser vice Dealer . Figure 23 1. Blades side to side 2. Measure here 8. Low er the disc harge deector ...

  • Exmark VT691KA484CA - page 38

    Maintenance Figure 26 1. Rear lift points 2. Engine deck brackets 7. T o raise the front of the mo wing deck, tighten the front locking nuts b y the same amount on both front adjusting rods . Tighten both rear locking nuts . Check the side to side lev el of the mow er again; refer to Deck Leveling . Note: Rak e adjustments may affect the motion con ...

  • Exmark VT691KA484CA - page 39

    Maintenance Checking the Tire Pressure in Driv e System Maintenance. 4. Disengag e the park brak e. 5. Push do wn on the brake bar until it touc hes the tires . There will be a 3/4 inch (19 mm) gap between the park brake handle and the slot in the control panel (see Figure 28). Figure 28 1. Brake bar 4. 3/4 inch (19 mm) 2. Push down 5. Park brake h ...

  • Exmark VT691KA484CA - page 40

    Maintenance Figure 31 1. Switch 3. Brake lever 2. 1/8 inch (3mm) gap needed between switch and brake lever 9. If needed, loosen the screws holding the switch and adjust the switch. Electric Clutch Adjustment No adjustment necessar y . How ever when the clutc h brake has w orn to the point where the clutc h no longer engag es consistently , the shim ...

  • Exmark VT691KA484CA - page 41

    Maintenance G011733 1 Figure 34 1. Feeler gauge Figure 35 1. Feeler gauge • If the gap is less than 0.010 inc h, then reinstall the shim and reference the T roubleshooting section. • If the g ap is sufcient, proceed to the safety chec k in step F. F . P erfor m the follo wing safety c heck: a. Sit on the seat and start the engine. b . Mak e ...

  • Exmark VT691KA484CA - page 42

    Maintenance Figure 37 1. Lock nut 3. Lock nut (LH thread) 2. Adjustment rod 7. Continue to rotate the adjustment rod, counting the turns, until the LCD indicator turns off . R otate the adjustment rod in the opposite direction half the n umber of turns counted. R elease the LH motion control lever and tighten the lock nuts on the right side . 8. T ...

  • Exmark VT691KA484CA - page 43

    Maintenance 6. Check the alignment on the LH and RH neutral switches upper and lower surfaces (reference Figure 39). If they are not in alignment, loosen the hardware on the lo wer neutral switc h and adjust it forward or rearw ard as necessar y . Once aligned, tighten the hardware . Check the neutral switc h alignment ag ain as the dec k is mov ed ...

  • Exmark VT691KA484CA - page 44

    Maintenance Figure 41 1. Switch screws 2. Nut and bolt 3. Cam 4. Front reference/speed control handle 8. After the cam is adjusted, the lever switch needs to be c heck ed. 9. Check the gap between the control lev er and switch as shown in Figure 42. The gap needs to be an 1/8 inc h (3mm) with the right motion control lever in the neutral, operate p ...

  • Exmark VT691KA484CA - page 45

    Maintenance Cleaning Clean Engine and Exhaust System Area Service Interval: Before each use or daily (May be required more often in dry or dirty conditions.) CAUTION Excessi v e de bris around engine cooling air intake and exhaust system area can cause engine, exhaust area, and h ydraulic system to o verheat which can create a re hazard. Clean a ...

  • Exmark VT691KA484CA - page 46

    Maintenance Battery Disposal DANGER Batter y electrolyte contains sulfuric acid, which is poisonous and can cause sev ere bur ns. Sw allowing electrol yte can be fatal or if it touches skin can cause sev ere bur ns. • W ear safety g lasses to shield eyes, and r ub ber glo ves to protect skin and clothing when handling electrol yte. • Do Not s w ...

  • Exmark VT691KA484CA - page 47

    T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use. When a problem occurs , do not ov erlook the simple causes . F or example: star ting problems could be caused by an empty fuel tank. The following table lists some of the common causes o ...

  • Exmark VT691KA484CA - page 48

    T roubleshooting Problem Possible Cause Cor rectiv e Action 1. Engine load is ex cessiv e 1. Reduce the g round speed. 2. Air cleaner is dirty . 2. Clean or replace the air cleaner element. 3. Oil lev el in the crankcase is lo w . 3. Add oil to the crankcase. 4. Cooling ns and air passages for the engine are plug ged. 4. Remov e the obstructions ...

  • Exmark VT691KA484CA - page 49

    T roubleshooting Problem Possible Cause Cor rectiv e Action 1. Fuse is blown. 1. Replace fuse . Check coil resistance, batter y charge, c harging system, and wiring connections and replace if necessar y . 2. Low voltage supply at the clutch. 2. Check coil resistance , battery charge, charging system, and wiring connections and replace if necessary ...

  • Exmark VT691KA484CA - page 50

    Schematics Schematics Electrical Diagram–All Units Except Kohler EFI 50 ...

  • Exmark VT691KA484CA - page 51

    Schematics Electrical Diagram–Kohler EFI 51 ...

  • Exmark VT691KA484CA - page 52

    Schematics Electrical Schematic–All Units Except Kohler EFI 52 ...

  • Exmark VT691KA484CA - page 53

    Schematics Electrical Schematic–Kohler EFI 53 ...

  • Exmark VT691KA484CA - page 54

    Schematics Hydraulic Diagram 54 ...

  • Exmark VT691KA484CA - page 55

    General Warranty Conditions and Pr oducts Covered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair , replace or adjust any part on these products and found by us (in the exercise of our reasonable discretion) to be defec ...

  • Exmark VT691KA484CA - page 56

    Notes: 56 ...

  • Exmark VT691KA484CA - page 57

    Service Record Date: Description of W ork Done: Service Done By: 57 ...

  • Exmark VT691KA484CA - page 58

    58 ...

  • Exmark VT691KA484CA - page 59

    G01 1841 Figure 44 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 20 degrees . Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 20 degrees. Fold along the appropriate line to match the recommended slope. 2. ...

  • Exmark VT691KA484CA - page 60

    MID-MOUNT RIDING A CCESSORIES AND OPTIONS EXMARK A CCESSORIES AND OPTIONS* W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM RIDE SEA T SUSPENSION SYSTEM FULL SUSPENSION SEA T DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT 12 V PO WER PORT MICRO-MULCH SYSTEM OPERA T OR CONTROLLED DISCHARGE SUN SHADE TRA ...

Manufacturer Exmark Category Lawn Mower

Documents that we receive from a manufacturer of a Exmark VT691KA484CA can be divided into several groups. They are, among others:
- Exmark technical drawings
- VT691KA484CA manuals
- Exmark product data sheets
- information booklets
- or energy labels Exmark VT691KA484CA
All of them are important, but the most important information from the point of view of use of the device are in the user manual Exmark VT691KA484CA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Exmark VT691KA484CA, service manual, brief instructions and user manuals Exmark VT691KA484CA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Exmark VT691KA484CA.

Similar manuals

A complete manual for the device Exmark VT691KA484CA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Exmark VT691KA484CA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Exmark VT691KA484CA.

A complete Exmark manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Exmark VT691KA484CA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Exmark VT691KA484CA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Exmark VT691KA484CA, that we can find in the current document
3. Tips how to use the basic functions of the device Exmark VT691KA484CA - which should help us in our first steps of using Exmark VT691KA484CA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Exmark VT691KA484CA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Exmark VT691KA484CA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Exmark VT691KA484CA?

Use the form below

If you did not solve your problem by using a manual Exmark VT691KA484CA, ask a question using the form below. If a user had a similar problem with Exmark VT691KA484CA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)