English dropdown-ico

Manual Husqvarna 8527SBE

32 pages 1.55 mb
Download

Go to site of 32

Summary
  • Husqvarna 8527SBE - page 1

    8527SBE Owner's Manual ...

  • Husqvarna 8527SBE - page 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury . W ARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e ...

  • Husqvarna 8527SBE - page 3

    3 PRODUCT SPECIFICA TIONS Gasoline Capacity 4.0 Quarts and T ype: Unleaded Regular only Oil T ype SAE 30 (above 40°F) (API SG–SL): SAE 5W-30 or 10W-30 (0° to +40°F) SAE 0W-30 (below 0°F) Oil Capacity: 28 Ounces Spark Plug: Champion RJ19LM (Gap: .030") CONGRA TULA TIONS on your purchase of a new snow thrower . It has been designed, engine ...

  • Husqvarna 8527SBE - page 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CART ON ...

  • Husqvarna 8527SBE - page 5

    5 ASSEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factor ...

  • Husqvarna 8527SBE - page 6

    6 ASSEMBL Y / PRE-OPERA TION INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. With top end of rod positioned under right side of control panel, push down on rod and insert ...

  • Husqvarna 8527SBE - page 7

    7 ASSEMBL Y / PRE-OPERA TION CHECK TIRE PRESSURE The tires on your snow thrower were overinfl ated at the fac- tory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI (19-24.5 N-m). INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The mult ...

  • Husqvarna 8527SBE - page 8

    8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat ...

  • Husqvarna 8527SBE - page 9

    9 OPERA TION Choke control - used for starting a cold engine. T raction drive control lever - used to engage power-pro- pelled for ward or reverse motion of snow thrower. Defl ector remote control lever - used to change the dis tance the snow is thrown. Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - ...

  • Husqvarna 8527SBE - page 10

    10 TO USE CHOKE CON TROL (See Fig. 13) The choke con trol is located on the en gine. Use the choke control when ev er you are starting a cold en gine. Do not use to start a warm en gine. The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shie ...

  • Husqvarna 8527SBE - page 11

    11 TO MOVE FOR W ARD AND BACKW ARD (See Fig. 17) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or revers ...

  • Husqvarna 8527SBE - page 12

    12 TO ADJUST SKID PLA TES (See Fig. 18) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow i ...

  • Husqvarna 8527SBE - page 13

    13 COLD ST ART - ELECTRIC ST ARTER 1. Insert safety ignition key into the ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place throttle control in F AST position. 3. Rotate choke control to FULL position. 4. Connect the power cord to the engine. 5. Plug the other end of the power cord int ...

  • Husqvarna 8527SBE - page 14

    14 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to prop ...

  • Husqvarna 8527SBE - page 15

    15 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The V -belts on your snow thrower are of special co ...

  • Husqvarna 8527SBE - page 16

    16 W ARNING: T o avoid serious injury , before per- forming any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug. SNOW THROWE ...

  • Husqvarna 8527SBE - page 17

    17 SER VICE AND ADJUSTMENTS TO REPLACE BEL TS (See Fig. 22) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a qualifi ed service center . NOTE: It is recommended that both the auger and traction drive belt be repl ...

  • Husqvarna 8527SBE - page 18

    18 ST ORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. W ARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open fl ame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli anc ...

  • Husqvarna 8527SBE - page 19

    19 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Refi ll fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to F AST position. 5. Choke in OFF position ...

  • Husqvarna 8527SBE - page 20

    20 REP AIR P ARTS AUGER HOUSING / IMPELLER ASSEMBL Y SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03 6 6 6 5 9 12 7 8 6 11 27 57 10 10 13 4 14 16 15 36 37 50 47 42 42 44 27 27 43 43 46 38 45 41 40 39 34 32 49 19 48 51 33 35 56 27 30 31 28 19 55 28 19 55 26 25 24 25 24 26 10 22 18 21 53 19 54 54 23 20 23 29 21 53 19 20 18 ...

  • Husqvarna 8527SBE - page 21

    21 KEY P ART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley , Impeller 5 532 18 89-09 Bearing Assembly , Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-55 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 872 27 05-05 Bolt, Carriage 5/16-1 8 x 5/8 9 532 17 88-20 Nut, Cage 3/8-16 10 532 18 82-1 1 Housing, Auger 1 1 532 18 40-90 Bar , Scraper 12 532 18 ...

  • Husqvarna 8527SBE - page 22

    22 REP AIR P ARTS CONTROL P ANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03 3 2 1 1 2 6 19 2 2 14 26 28 27 27 25 20 29 24 31 30 7 4 5 6 8 8 16 18 17 10 14 3 13 15 9 22 11 12 ...

  • Husqvarna 8527SBE - page 23

    23 KEY P ART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 17 86-74 Control Assembly , Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 Washer , Flat 3/8 6 532 17 86-59 Control Assembly , Chute Rotater 7 532 18 40-89 Support, Pivot 8 532 15 00-78 Screw , Hex Head 5/16-18 x 3/4 9 532 18 45-05 Spring ...

  • Husqvarna 8527SBE - page 24

    24 REP AIR P ARTS HANDLES SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03 32 31 32 30 31 12 10 11 13 15 15 12 16 17 16 23 22 27 41 27 22 17 11 15 15 14 38 39 40 37 33 35 35 34 34 42 43 44 45 46 46 7 6 36 2 5 5 3 1 4 4 4 4 3 8 28 28 9 18 19 20 21 26 24 24 25 5 5 ...

  • Husqvarna 8527SBE - page 25

    25 KEY P ART NO. NO. DESCRIPTION 1 532 18 41-10 Lever , Auger Control, RH 2 532 18 41-09 Lever , T raction Drive Control, LH 3 532 17 94-39 Nut, Cage 1/4-20 4 532 17 88-88 Bushing, Flange 5 532 16 96-75 Retainer , Hairpin 6 532 18 04-02 Screw , Hex Head 1/4-20 x 3/4 7 532 17 86-52 Rod, Interlock 8 532 19 95-76 Arm, Impeller Rod 9 532 19 95-75 Arm, ...

  • Husqvarna 8527SBE - page 26

    26 REP AIR P ARTS DRIVE SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03 4 4 4 1 2 5 3 5 1 2 3 1 20 21 17 19 18 18 7 7 2 2 2 24 23 12 32 27 44 22 16 15 2 4 4 13 1 2 5 3 42 42 3 5 8 9 10 6 3 41 14 43 11 35 33 15 41 22 34 29 22 31 26 25 28 30 40 39 38 36 37 33 ...

  • Husqvarna 8527SBE - page 27

    27 KEY P ART NO. NO. DESCRIPTION 1 532 14 63-15 Screw , Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, Lock 5/16-18 3 532 15 54-15 Washer , Flat 4 817 49 05-08 Screw , Hex Head 5/16-18 x 1/2 5 532 18 00-17 Bearing, Flange 6 532 18 01-34 Shaft, Auxiliary 7 532 17 92-70 Spacer , Plate 8 532 19 29-07 Plate, Auxiliary 9 532 18 00-82 Gear , Intermediate (12 ...

  • Husqvarna 8527SBE - page 28

    28 REP AIR P ARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03 6 19 17 10 21 22 23 2 1 3 4 6 7 8 9 12 13 15 27 26 25 24 18 7 6 20 14 47 47 48 46 40 44 49 50 51 52 35 55 34 33 32 38 36 41 6 37 39 42 43 11 53 54 11 44 45 41 30 29 31 31 58 16 10 21 28 57 6 11 ...

  • Husqvarna 8527SBE - page 29

    29 KEY P ART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, T raction Idler 2 532 18 05-22 Pulley , Idler (2-1/4) 3 - - - Engine, T ecumseh, Model Number LH185A (For engine service and replacement parts, call T ecumseh Products at 1-800-558-5402) 4 874 78 05-20 Screw , Hex Head 5/16-18 x 1-1/4 6 532 05 92-89 Washer , Flat 7 873 93 05-00 Nut, Jam, Lock ...

  • Husqvarna 8527SBE - page 30

    30 REP AIR P ARTS WHEELS / DECALS SNOW THROWER - MODEL NO. 8527SBE (96193000300), PRODUCT NO. 961 93 00-03 3 2 4 4 5 5 6 6 4 4 1 2 5 3 4 2 10 7 6 8 9 1 11 3 13 ...

  • Husqvarna 8527SBE - page 31

    31 KEY P ART NO. NO. DESCRIPTION 1 532 18 78-33 Wheel Assembly , 16", LH 2 532 15 54-43 Pin, Klik 1/4 3 532 18 78-65 Wheel Assembly , 16", RH 4 532 14 63-15 Screw , Hex Head 5/16-18 x 5/8 5 532 17 98-30 Bearing, Axle 6 532 17 46-97 Washer , Thrust (1") KEY P ART NO. NO. DESCRIPTION 1 532 18 10-38 Decal, Danger 2 532 19 13-76 Decal, H ...

  • Husqvarna 8527SBE - page 32

    532 19 83-79 Rev . 4 05.25.06 BY Printed in U.S.A. S E C T I ON 1: L I MIT E D W A R R A N T Y Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original pur- chaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: L ...

Manufacturer Husqvarna Category Snow Blower

Documents that we receive from a manufacturer of a Husqvarna 8527SBE can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 8527SBE manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 8527SBE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 8527SBE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 8527SBE, service manual, brief instructions and user manuals Husqvarna 8527SBE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 8527SBE.

Similar manuals

A complete manual for the device Husqvarna 8527SBE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 8527SBE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 8527SBE.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 8527SBE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 8527SBE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 8527SBE, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 8527SBE - which should help us in our first steps of using Husqvarna 8527SBE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 8527SBE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 8527SBE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 8527SBE?

Use the form below

If you did not solve your problem by using a manual Husqvarna 8527SBE, ask a question using the form below. If a user had a similar problem with Husqvarna 8527SBE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)