English dropdown-ico

Manual Pelco FX82012

36 pages 1.07 mb
Download

Go to site of 36

Summary
  • Pelco FX82012 - page 1

    ® INST ALLA TION FX82012 Unmanaged Ethernet Switch One 10BASE-T/100BASE-TX Port and T wo 100BASE-FX Fiber Ports C2624M (6/07) ...

  • Pelco FX82012 - page 2

    2 C2624M (6/07) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Not ices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Product Overview . . . . . . . . . . . . . . . . . ...

  • Pelco FX82012 - page 3

    C2624M (6/0 7) 3 List of T ables A TX Mode Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 B FX Mode Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 C Troubleshooting with Front-Panel Indicators . . . . . . . . . . . ...

  • Pelco FX82012 - page 4

    4 C2624M (6/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any ventilation open ings. Inst all in accordance with the manufacturer’ s instructions. 8. Do not install n ...

  • Pelco FX82012 - page 5

    C2624M (6/0 7) 5 The product and/or manual may bear the following marks: This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO N ...

  • Pelco FX82012 - page 6

    6 C2624M (6/07) Regulatory Notices This device complies with Part 15 of the FCC Rule s. Operation is subject to the following two conditions: (1) this device may not cause harmful in terference, and (2) this device must accept any interference received, including interfer ence that may cause undesired operation. RADIO AND TELEVIS ION INTERFERENCE T ...

  • Pelco FX82012 - page 7

    C2624M (6/0 7) 7 Product Overview DESCRIPTION The FX82012 unmanaged Ethernet switch provides one 10BASE-T/100BASE- TX port and two 100BASE-FX fiber ports for the transport of bidi rectional Ethernet data. Available in multimode and single-mode versions, the fiber ports use wavelength di vision multip lexing (WDM), wh ich al lows bidirectional data ...

  • Pelco FX82012 - page 8

    8 C2624M (6/07) Features of the FX 82012 Ethernet switch include the following: • User -selectable 10BASE-T/100BAS E-TX networking functions: – Autonegotiation between 10 Mbps and 100 Mbps data rates and between full-duplex and half-duplex modes – 10 Mbps or 100 Mbps selectable – Full-duplex or half-duplex mode selectable – Enabling/disab ...

  • Pelco FX82012 - page 9

    C2624M (6/0 7) 9 MODELS The FX82012 module consists of t he followin g series of models: Multimode Models:* FX82012MSTR-2 Unmanaged Ethernet switch, one 10BASE-T/100BASE-TX port, two multimode ST fiber ports, one fiber per port (total of two fibers) FX82012MSCR-2 U nmanaged Ethernet switch, one 10B ASE-T/100BASE-TX port, two multimode SC fiber port ...

  • Pelco FX82012 - page 10

    10 C2624M (6/07) FRONT PANEL Figure 3 illustrates the front panel of the FX82012 module. Figure 3. Front Panel of FX82012 Module For detailed information about the front-panel LEDs, refer to the T roubleshooting section. ì RESET BUTTON (restarts the unit) î FIBER FA ILOVER (REDUNDANCY) MODE LED ï 100BASE-FX ST A TUS LED (per fiber port A and B) ...

  • Pelco FX82012 - page 11

    C2624M (6/0 7) 11 REAR PANEL Figure 4 illustrates the rear panel of the FX82012 module. Figure 4. Rear Panel of FX82012 Module (SC Fiber Connectors Shown) For additional informati on about rear -panel connections, refer to the Installation section. For detailed information about the RJ-45 LEDs, refer to the T roubleshooting section. ì RACK POWER/A ...

  • Pelco FX82012 - page 12

    12 C2624M (6/07) Installation PACKAGE CONTENTS The following it ems are supplied: 1 FX82012 module 1 Regulated switching power suppl y with four plug adapt ers (North American, Australian, U.K., and European configurations); 100-240 V A C, 50-60 Hz input, 12 VDC output 1 Wall clip with two 4 -40 x 0.250-inch Phillips pa n head screws with lock wa s ...

  • Pelco FX82012 - page 13

    C2624M (6/0 7) 13 Using the TX Mode switch, you can do the following: • Enable autonegotiation or select (force) a specific data rate and duplex mode: – Enabling autonegotiation allows the FX82012 mo dule to automatically negotiate with the device to which the port is connected fo r data rate and duplex modes of operation: 10 Mbps or 100 Mbps d ...

  • Pelco FX82012 - page 14

    14 C2624M (6/07) SETTING FIBER FAILOVER MODE NOTE: As a matter of convenience, it is recomm ended that y ou set fiber failover (redundancy) mode—if required—befor e mounting the FX8201 2 module into a ra ck or onto a wall. Fiber failover mode is disabled by default. The FX82012 module can operate in fiber failover mode to al low automatic fiber ...

  • Pelco FX82012 - page 15

    C2624M (6/0 7) 15 Ta b l e B . FX Mode Switch Settings MOUNTING The FX82012 module can be mounted into a rack or c an be used as a stand-alone module. As a stand- alone module, the unit can be placed on a desktop or can be mounted to a wall. NOTE: As a matter of convenience, it is recommended that you set t he modes of operation for each 10BASE-T/1 ...

  • Pelco FX82012 - page 16

    16 C2624M (6/07) MOUNTING THE FX82012 MODULE TO A WALL The FX82012 module can be mounted to a wall in the following ways: • Using the supplied wall clip fo r attachment of a single module to a wa ll. For installation instructions, refer to the Mounting the FX82012 Module Using the Wall Clip secti on. • Using the optional WM5001 wall mount kits, ...

  • Pelco FX82012 - page 17

    C2624M (6/0 7) 17 Figure 7. Mounting the FX82012 Module Using the Wall Cl ip UPPER FLANGE VERTI C AL MOUNTING HOLE (2) HORIZONT AL MOUNTING HOLE (2) LOWER FLANGE W ALL C LIP SC REW , PHILLIP S P AN HEAD WITH LO C K W A S HER (2) ...

  • Pelco FX82012 - page 18

    18 C2624M (6/07) CONNECTIONS Connections to the FX82012 module are made on the rear panel of the modul e (refer to Figure 8). Figure 8. FX82012 Connections (SC Fi ber Connectors Shown) As illustrated in Figure 8, FX82012 c onnections consist of the following: • Power connection – A 12 VDC or 24 VA C power supply can be us ed to power the module ...

  • Pelco FX82012 - page 19

    C2624M (6/0 7) 19 • Fiber connections – When connecting fiber between FX82012 models, connect fiber port A of one module to fiber port B of another module. Similarly , c onnect fiber port B of one module to fiber port A of another module. Note that ports A and B c onnect fiber between FX82012 models because of fiber wa velength compatibility: ? ...

  • Pelco FX82012 - page 20

    20 C2624M (6/07) Figure 9. Fiber Port Conn ections in Point-to-Point Application with Redundancy FX MODE POSITION 2: FIBER PORT B IS PRIMARY . FIBER PORT A IS SECONDARY . SECONDARY FIBER LINK PRIMARY FIBER LINK FX MODE POSITION 1: FIBER PORT A IS PRIMARY . FIBER PORT B IS SECONDARY . ...

  • Pelco FX82012 - page 21

    C2624M (6/0 7) 21 Figure 10. Fiber Port Connections in Samp le Drop-and-Repeat Application FX MODE POSITION 0: FIBER PORTS A AND B ARE INDEPENDENT . FX MODE POSITION 0: FIBER PORTS A AND B ARE INDEPENDENT . FX MODE POSITION 0: FIBER PORTS A AND B ARE INDEPENDENT . ...

  • Pelco FX82012 - page 22

    22 C2624M (6/07) T roubleshooting LED indicators on the front and rear panels of the FX82012 module allow you to monitor operational status: • LED indicators on the front panel allow y ou to monitor operating power , fiber redundancy mode status, 100BASE-FX port status, and optic signal/laser status. Refer to T able C for information about the fr ...

  • Pelco FX82012 - page 23

    C2624M (6/0 7) 23 Fiber Failover Mode LED ( ) Not lit The module is not in fiber redundancy mode. The FX Mode switch is set to position 0. If fiber redundancy is not required, no action is required. If fiber redundancy is required, power off the module, set the FX Mode switch to position 1 or 2 as appropriate, and then power on the module. For deta ...

  • Pelco FX82012 - page 24

    24 C2624M (6/07) 100BASE-FX Status LED ( ) Green A fiber link is established. — No action required. Flashing green Da ta activity is occurring on the fiber link—data is being transmitted or received. — No action required. Red Far end fault indication (FEFI). The optical signal transmitted from this port is not detected by the remote l ink par ...

  • Pelco FX82012 - page 25

    C2624M (6/0 7) 25 Optic Fault LED ( ) Green The optical signal is being received and laser is operating properly . — No action required. Red The optical signal is not being received. Remote module is not powered on. Check power connections. Replace power supply if necessary . Fiber optic cable is not connected. Check fiber optic connections. Fibe ...

  • Pelco FX82012 - page 26

    26 C2624M (6/07) T able D. T roubleshooting with Rear -Panel Indicators Indicator Color Meaning Possible Cause Corrective Action RJ-45 10BASE-T/100BASE-TX Port Stat us LED - Left (Link / Activity) Amber A 10BASE-T link is established. — If 10BASE-T operation is desired, no action is required. If 10BASE-T operation is not desired, refer to the Set ...

  • Pelco FX82012 - page 27

    C2624M (6/0 7) 27 RJ-45 10BASE-T/100BASE-TX Port Status LED - Left (Link/Activity) (Continued) Not lit A 10BASE-T or 100BASE-TX link cannot be established. A problem may exist with the cable: • Cable is not connected to the module or to the 10BASE-T/100BASE-TX compatible device. • Cable is defective. • Cable is not the proper cable type. • ...

  • Pelco FX82012 - page 28

    28 C2624M (6/07) RJ-45 10BASE-T/100BASE-TX Port St atus LED - Right (Duplex/Collision) Amber Port is set to 10BASE-T full- duplex mode. — If 10BASE-T full-duplex opera- tion is desired, no action is required. If 10BASE-T full- duplex operation is not desired, refer to the Setting 10BASE-T/100BASE-TX Port Modes of Operation section in this manual ...

  • Pelco FX82012 - page 29

    C2624M (6/0 7) 29 RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Green Port is set to 100BASE-TX full- duplex mode. — If 100BASE-TX full-duplex operation is desired, no action is required. If 100BASE-TX full-duplex operation is not desired, refer to the Setting 10BASE-T/100BASE-TX Port Modes of Operation section ...

  • Pelco FX82012 - page 30

    30 C2624M (6/07) RJ-45 10BASE-T/100BASE-TX Port Status LED - Right (Duplex/Co llision) (Continued) Not lit Port is set to 10BASE-T half- duplex mode and no collisions are detected.* — If 10BASE-T half-duplex operation is desired , no action is required. If 10BASE-T half- duplex operation is not desired, refer to the Setting 10BASE-T/100BASE-TX Po ...

  • Pelco FX82012 - page 31

    C2624M (6/0 7) 31 Specifications PERFORMANCE Switch T ype Unmanaged Layer 2 Switch Method Store and forward Switch Fabric Non-head-of-line blocking Data Rate 10/100 Mbps Compliance IEEE 802.3, 802.3u, 802.3x Interface Auto MDI/MDI-X Operating Mode Half-duplex or full-duplex Address T able Size 1,024 MAC address ent ries with automatic learning and ...

  • Pelco FX82012 - page 32

    32 C2624M (6/07) OPTICAL POWER BUDGET AND MAXI MUM TRANSMISSION DIST ANCE Model Number Number of Fibers Wavelength (T ransmit/Receive)* Optical Power Budget Maximum T ransmission Distance Fiber Port A Fiber Port B Multimode (62.5/125 μm) FX82012MSTR-2 2 (1 per port) 1310/850 nm 850/1310 nm 26 dB † 2 km (1.2 mi) ‡ FX82012MSCR-2 2 (1 per port) 1 ...

  • Pelco FX82012 - page 33

    C2624M (6/0 7) 33 Appendix. RJ-45 Connector Pinouts Figure 11 illustrates RJ-45 MDI/MDI-X connector pinouts. Figure 11. RJ-45 MDI/MDI-X Connector Pinouts T able E summarizes RJ-45 MDI/MDI-X connector pinouts. T able E. RJ-45 MDI/MDI-X Connector Pinouts Pin Num ber MDI (Normal Mode) MDI-X (Crossed Mode) 1 RX+ TX+ 2 RX- TX- 3T X + R X + 4 Not used No ...

  • Pelco FX82012 - page 34

    34 C2624M (6/07) The materials used in the manufacture of this document and its components are compliant to t he requirements of Directive 2002/95/EC. This equipment contains electrica l or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the E ur opean Union rega rding the disposal of waste electrical and ...

  • Pelco FX82012 - page 35

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warrant y are as noted be low: • Five years on fiber o ptic products and TW3 000 Series unshield ed twisted pair tr ...

  • Pelco FX82012 - page 36

    ® Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | G ermany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Ar ...

Manufacturer Pelco Category Switch

Documents that we receive from a manufacturer of a Pelco FX82012 can be divided into several groups. They are, among others:
- Pelco technical drawings
- FX82012 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco FX82012
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco FX82012.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco FX82012, service manual, brief instructions and user manuals Pelco FX82012. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco FX82012.

Similar manuals

A complete manual for the device Pelco FX82012, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco FX82012 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco FX82012.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco FX82012 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco FX82012, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco FX82012, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco FX82012 - which should help us in our first steps of using Pelco FX82012
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco FX82012
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco FX82012 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco FX82012?

Use the form below

If you did not solve your problem by using a manual Pelco FX82012, ask a question using the form below. If a user had a similar problem with Pelco FX82012 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)