English dropdown-ico

Manual Janome DC1050

48 pages Not applicable
Download

Go to site of 48

Summary
  • Janome DC1050 - page 1

    INSTR UCTION BOOK ...

  • Janome DC1050 - page 2

    IMPORTANT SAFETY INSTRUCTIONS This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervise ...

  • Janome DC1050 - page 3

    1 SECTION I. NAMES OF P AR TS Names of P ar t s ............................................................. 2 Standard Accessories ................................................... 3 Extension T ab le ............................................................. 3 SECTION II. GETTING READY TO SEW Connecting the P ower Supply ................... ...

  • Janome DC1050 - page 4

    2 q w e r t y u io !0 !1 !2 !3 !4 !6 !7 !8 !9 !5 @0 @1 @2 @3 @4 @5 @6 @7 @8 @9 #0 #1 #3 #4 #5 #6 Names of P ar ts q Extension table (Accessory bo x) w Needle plate e Needle threader r Thread cutter t F ace cover y Thread take-up le ver u Thread tension dial i Spool pin o Large spool holder !0 Bobbin winder spindle !1 Bobbin winder stopper !2 Hole f ...

  • Janome DC1050 - page 5

    3 qw e r t yu i o ! 0 !1 !2 !3 Standar d Accessories q Bobbin w Spool pin f elt e Needle set r Additional spool pin t Satin stitch f oot F y Zipper f oot E u A utomatic buttonhole f oot R i Seam ripper (Buttonhole opener) o Screwdriv er key !0 Lint brush !1 Small spool holder !2 Large spool holder !333 Spool stand Extension T able The e xtension ta ...

  • Janome DC1050 - page 6

    4 SECTION II. GETTING READY TO SEW Connecting the P ower Suppl y • Using the foot contr ol Tu rn off the pow er switch q . Inser t the f oot control plug w into the foot control jac k e . Inser t the machine plug r into the pow er inlet t . Inser t the power supply plug y into the w all outlet u . Tu rn on the pow er s witch q . The f oot control ...

  • Janome DC1050 - page 7

    5 Speed Control Slider Sewing speed can be v aried by the speed control slider according to your se wing needs. To increase sewing speed, slide the slider to the right. To decrease sewing speed, slide the slider to the left. Controlling Se wing Speed Depress the foot control to start the machine. The fur ther down y ou press on the foot control, th ...

  • Janome DC1050 - page 8

    6 q q q q q Start/Stop Button Low er the presser foot lifter . Press the start/stop button q to star t the machine. The machine star ts running slowly f or the first fe w stitches; it then r uns at the speed set by the speed control slider . Press the star t/stop button q again to stop the machine . NO TES: • The machine r uns slo wly as long as ...

  • Janome DC1050 - page 9

    7 t t t t t Cursor Buttons Use these buttons to mo ve the cursor u . Press button to mo ve the cursor to right. Press button to mo ve the cursor to left. y y y y y V alue Set Buttons Use these buttons to change the set v alue. Mov e the cursor under the digit you w ould like to change. Press button to increase the v alue. Press button to decrease t ...

  • Janome DC1050 - page 10

    8 Presser Foot Lifter The presser f oot lifter q raises and lowers the presser f oot. Y ou can raise the f oot about 1/4 ˝ (0.6 cm) higher than the normal up position w f or easy remov al of the presser f oot, or to help you place thick material under the f oot. q Presser foot lifter w Nor mal up position e Highest position q w e w e Removing and ...

  • Janome DC1050 - page 11

    9 Changing the Needle zx c Selecting Thread and Needles F or gener al sewing, use needle size 11/75 or 14/90. A fine thread and needle should be used f or sewing lightweight f abrics, so the f abr ic will not be marred. Heavy f abrics require a needle large enough to pierce the f abr ic without fra ying the needle thread. Alwa ys test the needle si ...

  • Janome DC1050 - page 12

    10 Bobbin Winding • Remo ving the bobbin Gently slide the hook cov er release button q to the r ight and remov e the hook co ver plate w . Lift out the bobbin. q Hook cov er release button w Hook cover plate • Horizontal spool pin Lift up the spool pin q . Place a spool of thread on the spool pin with the thread coming off the spool as shown. A ...

  • Janome DC1050 - page 13

    11 z x c • Winding the bobbin NO TE: Set the speed control slider at its f astest position for bobbin winding. x c v b q m z Dra w the thread from the spool. x Guide the thread around the thread guide. NO TE: For saf ety pur poses, the machine will stop automatically 2 minutes after the star t of bobbin winding. c Thread through the hole in the b ...

  • Janome DC1050 - page 14

    12 • Inserting the bobbin z Place a bobbin in the bobbin holder with the thread r unning off counterclockwise. q End of thread z x c v b x Guide the thread into the first notch w on the front side of the bobbin holder . w Notch c Dra w the thread to the left, sliding it between the tension spring blades . v Continue to dr aw the thread lightly un ...

  • Janome DC1050 - page 15

    13 z x c v b w z c v b x z Draw the end of the thread around the upper thread guide. Threading the Machine • Threading the machine CA UTION: Tu rn OFF the power s witch before threading the machine. x While holding the thread near the spool w , draw the end of the thread down around the chec k spring holder . w Spool c Fir mly dra w the thread up ...

  • Janome DC1050 - page 16

    14 q z x NO TE: The needle threader can be used with a #11 to #16 needle or a blue tipped needle . Thread siz es 50 to 90 are recommended. Needle Threader CA UTION: Tu rn OFF the power s witch when using the needle threader . c v z Lower the presser f oot. Raise the needle to its highest position. Pull down the needle threader knob q as f ar as it ...

  • Janome DC1050 - page 17

    15 Drawing up the Bobbin Thread z Raise the presser f oot. Hold the needle thread lightly with your left hand. x Press the needle up/down b utton q twice to low er and raise the needle to pick up the bobbin thread. q Needle up/down b utton c Pull both threads 4 ˝ to 6 ˝ (10 to 15 cm) under and behind the presser f oot. q z x c ...

  • Janome DC1050 - page 18

    16 LCD Display The LCD displa y shows the f ollowing inf or mation when the machine is turned on. q Stitch pattern number w Cursors e Stitch width r Stitch length q w er z x c z Press the cursor ke ys to mov e the cursor under the stitch pattern number . The cursors appear under both digits when turning the po wer on. x Press the v alue set ke ys t ...

  • Janome DC1050 - page 19

    17 Adjusting the Needle Thread T ension for a Straight Stitch • Correct tension q Needle thread (top th read) w Bobbin thread (bottom thread) e To loosen r To tighten The ideal straight stitch has threads loc ked between two lay ers of f abric, as illustrated (magnified to show detail). If you look at the top and bottom of the seam, notice that t ...

  • Janome DC1050 - page 20

    18 Adjusting the Needle Thread T ension for a Zigzag Stitc h F or an ideal zigzag stitch, the bobbin thread does not show on the right side (T op side) of the fabric, and the needle thread shows slightly on the wrong side (Bottom side) of the f abr ic. See the illustrations f or the correct appearance. To match this appearance, adjust the needle te ...

  • Janome DC1050 - page 21

    19 q e w Straight Stitch Sewing q Stitch pattern: 00 or 01 w Needle thread tension: 2 to 6 e Presser foot: Zigzag f oot A • Starting to sew Raise presser f oot and position the fabric next to a seam guide line on the needle plate (5/8 ˝ (1.6 cm) is most common). Lower the needle to the point where y ou want to star t. Lower the presser f oot and ...

  • Janome DC1050 - page 22

    20 Needle Plate The seam guides on the needle plate and the hook cov er help you to measure seam allo wance . The numbers on the needle plate indicate the distance between the center needle position q and the edge of the fabric w . q Center needle position w Edge of the f abr ic q w Number Distance (cm) Distance (inch) 10 15 30 40 3/8 1/2 5/8 1 1 1 ...

  • Janome DC1050 - page 23

    21 q e w q e w q e w Lock-a-Matic Stitch q Stitch patter n: 02 w Needle thread tension: 2 to 6 e Presser foot: Zigzag f oot A r Re verse button Use this stitch to secure the beginning and the end of a seam with backstitching. When you reach the end of the seam, press the re v erse stitch button r once . The machine will se w four re verse stitches, ...

  • Janome DC1050 - page 24

    22 q e w q e w Saddle Stitch q Stitch patter n: 19 w Needle thread tension: 3 to 6 e Presser f oot: Zigzag f oot A Sculpture Stitch q Stitch patter n: 18 w Needle thread tension: 3 to 6 e Presser f oot: Satin stitch F F or top stitching and outlining designs. Sew slo wly at the cor ners. This saddle stitch is f or med with one stitch f orward, two ...

  • Janome DC1050 - page 25

    23 The zigzag stitch is one of the most useful and versatile stitches. It is used for overcasting, mending, appliqué, and also used as a decorative stitch. NOTE: Use an interfacing when sewing on stretch fabrics such as knit, jersey or tricot. q e w r u Zigzag Stitch q Stitch pattern: 10 w Needle thread tension: 2 to 6 e Presser foot: Zigzag f oot ...

  • Janome DC1050 - page 26

    24 q e w Overcasting with Zigza g Stitch q Stitch patter n: 10 w Needle thread tension: 3 to 7 e Presser f oot: Zigzag f oot A q e w Multiple Zigzag q Stitch patter n: 11 w Needle thread tension: 3 to 6 e Presser foot: Zigzag f oot A This stitch is used to finish seams on synthetics and other f abrics that tend to pucker . The stitch is also e xcel ...

  • Janome DC1050 - page 27

    25 NO TES: •T o sew the b uttonholes 05 to 07, follo w the same procedure as Square BH (See page 26 to 27.). • The size of a b uttonhole is automatically set by placing a button in the rear of automatic b uttonhole foot R. • The button holder of the f oot tak es a button size of up to 1 ˝ (2.5 cm) in diameter . • It is sometimes necessar y ...

  • Janome DC1050 - page 28

    26 q e w Square Buttonhole q Stitch patter n: 05 w Thread tension dial: 1 to 5 e Presser f oot: A utomatic buttonhole f oot R r Buttonhole lev er sign t y u i !0 o z x e r c v • T o sew z Press the needle up/down b utton to raise the needle. Attach the automatic b uttonhole foot R snapping the pin w into the slit q of the f oot holder . q Slit w ...

  • Janome DC1050 - page 29

    27 b b Star t the machine to sew the b uttonhole. The buttonhole will be automatically se wn. The machine will sew the left ro w first. n m n The machine will sew the bac k bar tack and the right row . m The machine will sew the front bar tac k, then it stops automatically . NO TE: If you start sewing the buttonhole without lo wering the b uttonhol ...

  • Janome DC1050 - page 30

    28 Adjusting the Stitch Width and Density for Buttonholes • Adjusting the stitch width Press the cursor buttons to move the cursor under the stitch width value “5.0” q (default setting). Press the button to decrease buttonhole width w . Press the button to increase buttonhole width e . The stitch width can be varied from 2.5 to 7.0 depending ...

  • Janome DC1050 - page 31

    29 q e w Corded Buttonhole q Stitch patter n: 05 w Thread tension dial: 1 to 5 e Presser foot: A utomatic buttonhole f oot R z Use the same procedure as the square buttonhole procedure. Set the stitch width to match the thickness of the cord used. With the buttonhole f oot raised, hook the filler cord on the spur q at the back of the buttonhole f o ...

  • Janome DC1050 - page 32

    30 q e w Darning Stitch q Stitch pattern: 08 w Thread tension dial: 3 to 6 e Presser f oot: A utomat ic b uttonhole foot R • Starting to sew z Pull the b utton holder q to the back. x Place the garment under the foot. Press the needle up/down b utton twice. Mov e the f abr ic to the left to dra w both threads under the f oot. c Low er the foot an ...

  • Janome DC1050 - page 33

    31 q e w q r t w r e Ta c king q Stitch pattern: 09 w Thread tension dial: 3 to 6 e Presser foot: Satin stitch foot F Ta cking is used to reinf orce pock ets, crotches and belt carriers where extra strength is needed. • Star t se wing Star t the machine and sew until the machine stops automatically . The machine will sew a tacking 1.5 cm (5/8 ˝ ...

  • Janome DC1050 - page 34

    32 q e w Zipper Se wing q Stitch patter n: 00 w Needle thread tension: 1 to 4 e Presser f oot: Zigzag f oot A Zipper f oot E w er • Attaching the zipper foot Fit the pin on the zipper f oot into the slit of the foot holder . • T o sew the left side of the zipper , attach zipper foot with the right-hand side of pin. • T o sew the right-side of ...

  • Janome DC1050 - page 35

    33 x c i o v !0 !1 b n !2 m Zipper Sewing (continued) x Attach the zipper foot with the pin on the right. Sew through all the lay ers from the end of the zipper opening, guiding the zipper teeth along the edge of the f oot. c Stop the machine 2 ˝ (5 cm) before the f oot reaches the slider on the zipper tape. Low er the needle into the f abr ic, an ...

  • Janome DC1050 - page 36

    34 q e w Blind Hemming q Stitch pattern: 15 w Thread tension dial: 1 to 4 e Presser f oot: Zigzag foot A z F old a hem with the wrong side of the fabric up to fo r m a 1/4 ˝ – 7/16 ˝ (0.4 – 0.7 cm) allowance . q Wrong side of fabric w 1/4 ˝ – 7/16 ˝ (0.4 – 0.7 cm) (1) On heavyweight f abrics that tend to rav el, the ra w edge should be ...

  • Janome DC1050 - page 37

    35 q e w r Button Sewing q Stitch patter n: 10 w Needle thread tension: 3 to 7 e Presser foot: Satin stitch f oot F r F eed dog: Dropped z Lower the f eed dog. x Match the holes of button to the horizontal slot on the presser foot. c Lower the f oot to hold the button in place. v Adjust the stitch width so the needle will enter the left hole of the ...

  • Janome DC1050 - page 38

    36 q e w Scallop Stitch q Stitch patter n: 23 w Thread tension dial: 3 to 6 e Presser f oot: Zigzag f oot A Sew the stitches appro ximately 3/8 ˝ (1 cm) inside the edge of the f abr ic. Tr im the outside of the stitches as shown. Make sure y ou don’t cut the thread. qe w Applique q Stitch patter n: 31, 32 or 33 w Needle thread tension: 1 to 4 e ...

  • Janome DC1050 - page 39

    37 q e w P atchwork Piecing q Stitch patter n: 00 and 21 w Thread tension dial: 3 to 6 e Presser foot: Zigzag f oot A w z Place the patchw or k pieces r ight sides together . Select stitch pattern 00. Sew a precise 1/4 ˝ seam allowance . q Wrong side of fabric w Right side of fabric x Select stitch patter n 21. c Press the seam allow ance to open. ...

  • Janome DC1050 - page 40

    38 q e w Fa goting q Stitch patter n: 34 w Thread tension dial: 3 to 6 e Presser f oot: Satin stitch f oot F Use this stitch to join two pieces of f abric to create an open work appearance and add design interest. F old under each fabric edge 5/8 ˝ (1.5 cm) and press. Pin the two edges to paper or tear bac king 1/8 ˝ apar t. Sew slowly , guiding ...

  • Janome DC1050 - page 41

    39 Cross Stitch q Stitch P atter n: 36 w Thread tension dial: 3 to 6 e Presser foot: Satin stitch foot F q e w Y ou can make cross stitch designs with these patterns, in half the time it would take if embroidered b y hand. * If you press the auto-loc k button bef ore sewing, the machine will sew one unit of the cross stitch and stop automatically . ...

  • Janome DC1050 - page 42

    40 q e w Decorative Stitch Combinations q Stitch Pattern: 41 and 43 w Thread tension dial: 3 to 6 e Presser f oot: Satin stitch f oot F q Correcting Distorted Stitch P atterns The sewing results of the stretch patterns ma y vary depending upon the sewing conditions , such as sewing speed, type of the f abr ic , number of lay ers etc. Alwa ys test s ...

  • Janome DC1050 - page 43

    41 SECTION V . CARE OF Y OUR MA CHINE Cleaning the Hook Race and Feed Dog W ARNING: • T ur n the power s witch off and unplug the machine before cleaning. • Do not dismantle the machine other than as e xplained in this section. CA UTION: Do not store the machine in a high-humidity area, near a heat radiator , or in direct sunlight. Installing t ...

  • Janome DC1050 - page 44

    42 Audible signal Pip Pip-pip-pip Pip-pip-peep Peep The buzzer sounds when: Normal operation Invalid operation Buttonhole sewing completed Malfunction Pr oblems and W arning Signs Cause Try this The machine will not sew with the star t/stop button because the foot control is connected. Disconnect the foot control and star t the machine. Warning sig ...

  • Janome DC1050 - page 45

    43 Tr oubleshooting Condition The needle thread breaks. The bobbin thread breaks. The needle breaks. Skipped stitches Seam puckering The cloth is not f eeding smoothly . Stitches f orm loops below the w orks. The machine does not w ork. Buttonhole sewing is not sewn pr operly . The machine does not run smoothly and is noisy . Abnormal noise from th ...

  • Janome DC1050 - page 46

    ...

  • Janome DC1050 - page 47

    ...

  • Janome DC1050 - page 48

    808-800-361(Eng) Printed in T aiwan ...

Manufacturer Janome Category Sewing Machine

Documents that we receive from a manufacturer of a Janome DC1050 can be divided into several groups. They are, among others:
- Janome technical drawings
- DC1050 manuals
- Janome product data sheets
- information booklets
- or energy labels Janome DC1050
All of them are important, but the most important information from the point of view of use of the device are in the user manual Janome DC1050.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Janome DC1050, service manual, brief instructions and user manuals Janome DC1050. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Janome DC1050.

Similar manuals

A complete manual for the device Janome DC1050, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Janome DC1050 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Janome DC1050.

A complete Janome manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Janome DC1050 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Janome DC1050, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Janome DC1050, that we can find in the current document
3. Tips how to use the basic functions of the device Janome DC1050 - which should help us in our first steps of using Janome DC1050
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Janome DC1050
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Janome DC1050 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Janome DC1050?

Use the form below

If you did not solve your problem by using a manual Janome DC1050, ask a question using the form below. If a user had a similar problem with Janome DC1050 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)