English dropdown-ico

Manual Cub Cadet 730 STE

28 pages 7.32 mb
Download

Go to site of 28

Summary
  • Cub Cadet 730 STE - page 1

    Oper ator’ s Man ual PRINTED IN U .S.A. IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y WARNING: This unit is equipped with an inte rnal combustion engine and should not be us ed on or near any unimproved forest- covered, brush-covered or grass-covered lan d unless the engi ne’s exhaust system is equipped with a spark arrester mee ...

  • Cub Cadet 730 STE - page 2

    2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Ma nual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and unde rstand what it says. Before you star t assembling your new equipment , please locate the model plate on the equipment and copy th e info ...

  • Cub Cadet 730 STE - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES DANGER: This machine was built to be operated according to th e rules for safe operation in this manual. As with any type of power equipment, car elessness or error on the part of the oper ator can result in serious injury. This machine is capable of amputatin g hands and feet and throwing objects. Fa ...

  • Cub Cadet 730 STE - page 4

    4 5. Never run an engine in doors or in a poo rly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate machine while under the influen ce of alcohol or drugs. 7. Muffler and engine become hot and can ca use a burn. Do not touch. 8. Exercise extreme caution wh en operating on or crossing gravel surf ...

  • Cub Cadet 730 STE - page 5

    5 SECTION 1: ASSEMBLING YOUR SNOW THROWER Unpacking • Remove screws from the to p sides and ends of the shipping crate. • Set panel aside to avoid t ire punctures or personal injury. • Remove and discard plastic bag th at covers unit. • Remove any loose parts included with unit (i.e., Operator’s Manu al, etc.). • Roll unit out of crate. ...

  • Cub Cadet 730 STE - page 6

    6 Figure 3 • If not alre ady attached, unwrap the headlight wire which is attached to the he adlight, beneath the handle panel. Win d the headlight wire aroun d the lower right handle until excess slack is removed. See Figure 4. • Plug the wire from th e headlight into the alternat or lead coming from the righ t side of the engine undernea th t ...

  • Cub Cadet 730 STE - page 7

    7 The drive control also locks the auger control so you can turn the chute dire ctional control without interrupting t he snow throwing process. If the auger control is engaged al ong with the drive control, the operator can release th e auger control (on the left handle) and the a ugers will remain engaged. Release both controls to stop the augers ...

  • Cub Cadet 730 STE - page 8

    8 T rack Lock Lev er The track lock lever is located on t he right side of the snow throwe r and is use d to select the positi on of the auger housin g and the method o f track operation. M ove the lever to the right, then forward or backward to one of the three posit ions. See Figure 6. Transport: Raises the front en d of the snow throwe r for eas ...

  • Cub Cadet 730 STE - page 9

    9 • Rotate ch oke knob to FULL ch oke posit ion (cold engine start). If engin e is warm, place choke in OFF position inste ad of FUL L. • Push pr imer button two or thr ee times fo r cold engine star t, making sure to co ver vent ho le in primer butt on when pushin g. DO NOT use primer to restart a wa rm engine after a short shutdown. • Push ...

  • Cub Cadet 730 STE - page 10

    10 IMPORT ANT: If the auger shows ANY signs of rotating, immediately return to the ope rator’s position and shut off the engine. Wait for ALL moving parts t o stop before re-adjusting th e auger control. • To readjust th e control cable, loosen the hex jam nut on the auger cont rol cable “Z” fitting. • Rotate the co upling end of the ca b ...

  • Cub Cadet 730 STE - page 11

    11 SECTION 4: MAKING ADJUSTMENTS WARNING: NEVER attempt to m ake any adjustments while the en gine is running, except where specified in the operator’s manual. Chute Assembly The distance snow is thrown can be adjusted by changing the angle o f the upper chute. Move the chut e tilt control fo rward to decrease the distance , toward th e rear to i ...

  • Cub Cadet 730 STE - page 12

    12 Shift Rod Adjustment To adjust t he shift rod , proceed as follows: • Remove the hairpin clip and slide the shift rod connector up , to separate the upper shift rod from the lower shift rod. See Figure 11. • Place the shift lever in to the sixth (6) posit ion. • Rotate the sh ift arm clockwise (f rom the opera tor’s position) as far as i ...

  • Cub Cadet 730 STE - page 13

    13 WARNING: If any a djustments need to be made to the engine wh ile the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of muffler, engine and other surrou nding heated surfaces. Drive / Auger Control Lock The cams on the ends of the control r ods which interlock the drive and auger controls must be lubricated at le ...

  • Cub Cadet 730 STE - page 14

    14 SECTION 6: SERVICING YOUR SNOW THROWER WARNING: Before ser vicing, repairing, or inspecting, disengag e all controls and stop engine. Wait until all moving parts have come to a complete stop. Disconn ect spark plug wire and groun d it against the engine to prevent unintende d starting. Always wear safety glasses dur ing operation or while perfor ...

  • Cub Cadet 730 STE - page 15

    15 • Tip the snow thr ower up and forward so that it rest s on its auger housing. Refer to Figure 9. • Remove the six self-tap ping screws from the frame cover underneath the snow thrower. • Roll the front an d rear auger belts of f the engine pulley. See Figure 17. • Unhook the idler spr ing from the hex bolt on the auger housing. See Figu ...

  • Cub Cadet 730 STE - page 16

    16 • Using a 7/8" wren ch to hold the shaft , loosen, but do not complet ely remove, the he x bolt and bell washer on the left end of gear shaft. See Figure 20. Figure 20 • Lightly tap the hex nut t o dislodge the ball bearing from the r ight side of frame b efore remo ving the he x nut and bell wash er from left end of sh aft. • Move th ...

  • Cub Cadet 730 STE - page 17

    17 SECTION 7: TROUBLESHOOTING Prob lem Cause Remedy Engine fails to start 1. Fuel tank empty, or stale fuel. 2. Blocked fuel line. 3. Choke not in the ON position 4. Faulty sp ark plug. 5. Safety key not in ignition switch on engine. 6. Spark plug wire di sconnected. 7. Primer button not being used properly. 1. Fill tank with clean, fresh gasoline ...

  • Cub Cadet 730 STE - page 18

    18 SECTION 8: PARTS LIST FOR MODEL 730 STE 1 11 19 5 6 17 7 22 11 27 21 8 Part of handle panel for reference on ly 25 4 9 3 24 20 14 26 11 19 30 29 32 34 38 39 40 41 42 9 11 45 45 46 47 48 49 50 51 52 53 54 54 55 56 57 58 59 60 40 61 62 63 64 65 9 67 68 69 72 70 71 9 53 40 16 74 75 76 77 9 64 73 68 79 43 78 10 75 75 16 15 12 2 18 11 37 31 35 66 36 ...

  • Cub Cadet 730 STE - page 19

    19 Model 730 STE Ref . No . P art No. P art Description 1. 684-0008A Shift Arm Assembly 2. 705-5204A Chute Directional Control 3. 710-0449 Carriage Screw 5/16-1 8 x 2.25 4. 710-0458 Carriage Bolt 5/16-1 8 x 1.75 5. 710-0643 Hex Bolt 5/16-18 x 1.0 6. 710-0788 TT Screw 1/4-20 x 1.0 7. 710-1880 Hex Bolt 5/16-18 x 0.75 8. 711-0677 Ferrule 9. 712-04063 ...

  • Cub Cadet 730 STE - page 20

    20 10 43 47 44 38 46 19 32 45 17 9 20 31 36 49 23 18 48 50 25 16 33 13 35 15 28 26 22 27 21 12 14 11 16 5 6 3 7 16 8 4 2 28 13 16 30 37 34 1 41 40 39 24 29 42 Model 730 STE ...

  • Cub Cadet 730 STE - page 21

    21 Model 730 STE Ref. No. P art No. P art Description 1. 714-04040 Cotter Pin 2. 756-0178 Flat Idler 3. 784-5632B Auger Idler Arm 4. 710-0347 Hex Cap Screw 3/8-16 x 1 .75 5. 738-0281 Shoulder Screw 6. 736-0174 Wave Washer 7. 732-0611 Extension Spring 8. 712-3068 Hex Nut 5/16-18 9. 710-0642 Self T apping Screw , 1/4-20 x.75 10. 711-04282 A uger Axle ...

  • Cub Cadet 730 STE - page 22

    22 Model 730 STE 15 25 19 26 27 24 23 22 21 16 17 18 19 20 29 30 31 32 32 32 34 30 32 27 26 19 25 36 21 24 23 22 12 2 30 10 18 19 20 2 1 13 11 14 9 3 7 6 5 4 2 40 39 38 28 8 35 41 33 37 29 29 ...

  • Cub Cadet 730 STE - page 23

    23 Model 730 STE NOTE: For painted parts , please refer to the list of color code s below. Please add the applicable col or code, wherever needed, to the part number to order a replacement part. For instance, if a part numbered 700-xxxx is painted Yard-Man Green, the part number to or der would be 700-xxxx-0665. Yard-Man Green: 0665 Yard-Man Yellow ...

  • Cub Cadet 730 STE - page 24

    24 Model 730 STE 1 2 6 3 10 12 7 8 5 4 9 13 15 14 17 16 19 20 22 22 20 19 28 21 18 21 18 15 13 14 29 31 32 30 30 32 34 37 38 36 23 35 27 39 11 40 41 42 44 45 51 46 47 48 52 46 53 51 54 55 54 50 16 17 49 37 24 25 26 26 33 33 56 56 ...

  • Cub Cadet 730 STE - page 25

    25 Ref. No. P art No. P art Description 1. 720-0223 Grip 2. 710 -0604A Tap Screw, 5/16-18 x.625 3. 784 -5642 Track Lockout Plate 4. 710 -0157 Hex Cap Scre w, 5/16-24 x.75 5. 736 -0242 Bell Washer 6. 684 -0038 Track Lock Handle Assembly 7. 710 -0459A Hex Cap Screw, 3/8-24 x 1.5 8. 712 -0214 Hex Nut, 3/8-24 9. 748 -0353A Lift Shaft Drive 10. 750-0547 ...

  • Cub Cadet 730 STE - page 26

    26 Model 730 STE 17 27 1 2 3 4 5 6 7 4 8 9 10 11 12 13 14 15 16 18 19 19 16 16 16 20 21 22 23 24 25 26 Ref. No. P art No. P art Description 1. 710-1652 Hex Washer Screw 1/4-20 x.62 5 2. 731-1324 Belt Cover 3. 732-0710 Extension Spring 4. 710-0627 Hex Screw 5/16-24 x.75 5. 710-3005 Hex Cap Screw 3/8-16 x 1 .25 6. 05896A Drive Clutch Idler Bracket 7. ...

  • Cub Cadet 730 STE - page 27

    27 Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-866-840-6483, 1-330-558-7220 MT D Canada Limited - KITCHENER, ON N2G 4J1; Phone 1-800-668-1238 MANUF A CTURER’S LIMITED COMMERCIAL W ARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise used for commercial purposes and pur ...

  • Cub Cadet 730 STE - page 28

    MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possession s and territories, and by MTD Products Limited with respect to new merch andise purchased and used in Canada an d/or its territories and possessions. “Cub ...

Manufacturer Cub Cadet Category Snow Blower

Documents that we receive from a manufacturer of a Cub Cadet 730 STE can be divided into several groups. They are, among others:
- Cub Cadet technical drawings
- 730 STE manuals
- Cub Cadet product data sheets
- information booklets
- or energy labels Cub Cadet 730 STE
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cub Cadet 730 STE.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cub Cadet 730 STE, service manual, brief instructions and user manuals Cub Cadet 730 STE. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cub Cadet 730 STE.

Similar manuals

A complete manual for the device Cub Cadet 730 STE, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cub Cadet 730 STE by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cub Cadet 730 STE.

A complete Cub Cadet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cub Cadet 730 STE - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cub Cadet 730 STE, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cub Cadet 730 STE, that we can find in the current document
3. Tips how to use the basic functions of the device Cub Cadet 730 STE - which should help us in our first steps of using Cub Cadet 730 STE
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cub Cadet 730 STE
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cub Cadet 730 STE in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cub Cadet 730 STE?

Use the form below

If you did not solve your problem by using a manual Cub Cadet 730 STE, ask a question using the form below. If a user had a similar problem with Cub Cadet 730 STE it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)