English dropdown-ico

Manual KitchenAid 42

24 pages 9.22 mb
Download

Go to site of 24

Summary
  • KitchenAid 42 - page 1

    Installation Instr uctions and Use and Car e Guide 36" (91 .4 cm) 42" (1 06.7 cm) 48" (121 .9 cm) W all-Mount Pr o Line ™ Rang e Hood IMPOR T ANT : Read and sa v e these instr uctions. IMPOR T ANT : Installer: L eave Installation Instructions with the homeowner . Homeowner: K eep Installation Instructions for future reference. Save ...

  • KitchenAid 42 - page 2

    Bef or e y ou start... Proper installation is your responsibility: • Have a qualified tec hnician install this range hood. • Comply with installation clearances specified on the model/serial rating plate. The model/ser ial rating plat e is located inside the range hood on the rear wall. Range hood location should be aw ay from strong draft area ...

  • KitchenAid 42 - page 3

    3 Cabinet dimensions Pr oduct dimensions V enting r equir ements • The size of the vent should be uniform. • Use no more than three 90° elbows. • Make sure there is a minimum of 24" (61 cm) of straight vent between the elbows if more than one elbow is used. • Do Not install two elbows together . • The length of vent system and numbe ...

  • KitchenAid 42 - page 4

    V ent Piece 3-1/4" x 1 0" (8.3 cm x 25 cm) 7" (1 7 .8 cm), 8" (20.3 cm), Rectangular 9" (22.9 cm), 1 0" (25.4 cm) Round 45° elbow 7 .0 feet 2.5 feet (2.1 m) (0.8 m) 90° elbow 5.0 feet 5.0 feet (1 .5 m) (1 .5 m) 90° flat elbow 12.0 feet (3.7 m) transition to round 5.0 feet (1 .5 m) w all cap 0.0 feet (0.0 m) 4 V enti ...

  • KitchenAid 42 - page 5

    Electr ical r equir ements Installation st eps Important: Observ e all gov er ning codes and ordinances. It is the customer’ s r esponsibility: •T o contact a qualified electr ical installer . •T o assure that the electr ical installation is adequate and in confor mance with National Electr ical Code, ANSI/NFP A 70 — latest edition*, or CSA ...

  • KitchenAid 42 - page 6

    5. The hood attac hes to the w all with the mounting screws located as shown. For the 36" (91 .4 cm) models, there are two mounting screws. For the 42" (1 06.7 cm) and 48" (121 .9 cm) models, there are four mounting screws. Install the screws into the wall until the screw heads are tight against the w all and horizontal. Note: The sc ...

  • KitchenAid 42 - page 7

    7 9. If roof or wall cap does not have a damper , at tac h damper to exhaust opening(s) on top of the hood using two Phillips-head screws. 10 . If 48" (121 .9 cm) hood is to be connected to 1 0" (25.4 cm) round vent system, install the vent transition piece now. Electr ical connection Electrical Shock Hazar d Disconnect power bef ore maki ...

  • KitchenAid 42 - page 8

    8 Use and Car e Inf or mation W ARNING — T o reduce the risk of fire or electrical shoc k, do not use this fan with any solid-state speed control device. W ARNING — T O REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y T O PERSONS, OBSER VE THE FOLL O WING: Use this unit only in the manner intended by the manufacturer . If you have questions, ...

  • KitchenAid 42 - page 9

    Opening the canopy hood contr ol panel: The hood controls are located on the right-hand underside of the canopy . Operating the light: ON: Move the light switc h to the “1” position. OFF: Move the light switc h to the “0” position. Operating the blo wer: ON: Move the blower switc h to the “1” position. OFF: Move the blower switc h to th ...

  • KitchenAid 42 - page 10

    Wa rr anty Kitc henAid ® Range Hood W ar ranty LENGTH OF W ARRANTY Kitc henAid WILL P A Y FOR LIMITED ONE-YEAR W ARRANTY Labor and any par ts of your range hood (except light bulbs and F rom Date of P urc hase filters) whic h are defecti ve in materials or workmanship. Kitc henAid WILL NO T P A Y FOR A. Consumable parts suc h as light bulbs and fi ...

  • KitchenAid 42 - page 11

    11 Requesting Assistance or Service Call the KitchenAid Cust omer Inter action Center t oll-free at 1 -800-235-0665. Our consultants ar e av ailable to assist you. When calling: Please know the purc hase date, and the complete model and serial number of your appliance This information will help us better respond to your request. Our consultants pro ...

  • KitchenAid 42 - page 12

    2. If y ou need service ✝ ... Contact your nearest Kitc henAid Canada Appli- ance Service branc h or authoriz ed servicing outlet to service your appliance. (See list below .) Make sure the service company you contact is authorized to service your appliance during the warr a n ty period. 1. If the pr oblem is not due to one of the it ems list ed ...

  • KitchenAid 42 - page 13

    Instr uctions d’installation et Guide d’utilisation et d’entr etien Hot t e d’aspir ation pour cuisinièr e Pr o Line ™ - montag e mur al 91,4 cm (36 po) 1 06,7 cm (42 po) 121,9 cm (48 po) IMPOR T ANT : Lir e et conserv er ces instr uctions. IMPOR T ANT : Installateur : R emettre les instructions d’installation au propriétaire de l’a ...

  • KitchenAid 42 - page 14

    Av ant de commencer . . . C’est à vous qu’incombe la responsabilité de : • Demander à un tec hnicien qualifié d’installer cette hot te. • Respecter lors de l’installation les dégagements de séparation spécifiés sur la plaque signalétique de l’appareil. La plaque signalétique (av ec numéro de modèle et numéro de sér ie) e ...

  • KitchenAid 42 - page 15

    3 Dimensions des placar ds Dimensions du pr oduit Cir cuit de déc har g e de l’air • La taille du conduit d’évacuation doit être uniforme. • Ne pas utiliser plus de trois coudes à 90°. • S’il est nécessaire d’installer plusieurs coudes, ceux -ci devront être séparés par une section rectiligne d’au moins 61 cm (24 po). • N ...

  • KitchenAid 42 - page 16

    Composant Conduit r ectangulaire Conduit rond, dia 8,3 x 25 cm (3 1/4 x 1 0 po) 1 7 ,8 cm ( 7 po), 20,3 cm (8 po) 22,9 cm (9 po), 25,4 cm (1 0 po) coude à 45° 2,1 m 0,8 m (7 pi) (2,5 pi) coude à 90° 1,5 m 1,5 m (5 pi) (5 pi) coude à 90° plat 3,7 m (12 pi) raccord de transition 1,5 m rectangle-rond (5 pi) bouc he de déc harge 0 m murale (0 pi ...

  • KitchenAid 42 - page 17

    3. P our une déc harge par l’arrière/horiz ontalement, si le circuit d’évacuation n’est pas installé, tracer et découper maintenant l’ouverture de passage du conduit. 4. Important : Si un dosseret doit être utilisé (option), on doit l’installer av ant la hot te. Si aucun dosseret n’est utilisé, passer à l’étape 5. Installati ...

  • KitchenAid 42 - page 18

    5b. Utilisation d’une extension de cheminée : Fixer les brides de l’extension selon l’illustration. V eiller à ce que les vis soient solidement fixées dans le mur . 9-11/16" (24.6 cm) 1-1/8" (2.9 cm) 1-1/4" (3.2 cm) 6-3/32" (15.5 cm) 10-1/2" (26.7 cm) Electrical opening Electrical opening C L C L 2-7/8" (7.5 c ...

  • KitchenAid 42 - page 19

    7 9. Si aucun volet de réglage n ’est associé à la bouc he de déc harge (murale ou sur le toit), installer le v olet de réglage dans l’ouver ture de déc harge au sommet de la hotte, avec deux vis Phillips. 10 . Si on doit raccorder la hotte de 121,9 cm (48 po) à un conduit d’évacuation de 25,4 cm (1 0 po), installer maintenant le racc ...

  • KitchenAid 42 - page 20

    8 Utilisation et entr etien A VER TISSEMENT - P our réduire le risque d’incendie ou de c hoc électrique, ne pas utiliser ce ventilateur en conjonction avec un dispositif de réglage de la vitesse à semi-conducteurs. A VER TISSEMENT - POUR MINIMISER LE RISQUE D’INCENDIE, CHOC ÉLECTRIQUE OU DOMMA GES CORPORELS, RESPECTER LES INSTRUCTIONS SUIV ...

  • KitchenAid 42 - page 21

    A vant de commencer , placer tous les commutateurs de la hotte à la posi- tion d’arrêt et vérifier que les lampes se sont suffisamment refroidies. La température de service d’une lampe à halogène est très élevée. P our remplacer une lampe à halogène : • Ôter les deux vis de la garniture métallique circulaire placée autour de la ...

  • KitchenAid 42 - page 22

    10 Sc hémas de câblag e A ccessoir es utilisables pour l’installation – option - disponibles c hez le revendeur local Note : Ces ensembles sont disponibles seulement en acier inoxydable. Dosser et* : Le dosseret doit être installé avant l’installation de la hotte. Hotte de 91,4 cm (36 po) : ensemble n° 8284756 Hotte de 1 06,7 cm (42 po) ...

  • KitchenAid 42 - page 23

    11 Gar antie Hot t e d’aspiration Kitc henAid ® DURÉE DE LA PÉRIODE DE GARANTIE Kitc henAid P AIERA GARANTIE LIMITÉE D’UNE ANNÉE Pièces et main-d’œuvre (sauf lampes et filtres) pour À compter de la date d’ac hat l’élimination d’un vice de matériau ou de fabrication. Kitc henAid NE P AIERA P AS A. Pièces consomptibles comme la ...

  • KitchenAid 42 - page 24

    Pièce N° 43294091/8284829 Rév . A © 20 0 1 Kitc henAid, U.S.A. ® Marque déposée de Kitc henAid, U.S.A., Kitc henAid porteur de licence au Canada 2/20 0 1 Imprimé aux É.-U. Demande d’assistance ou de service Service d’appareils ménagers KitchenAid Canada – Service aux consommateurs Succursales de service direct : COLOMBIE-BRIT ANNIQ ...

Manufacturer KitchenAid Category Ventilation Hood

Documents that we receive from a manufacturer of a KitchenAid 42 can be divided into several groups. They are, among others:
- KitchenAid technical drawings
- 42 manuals
- KitchenAid product data sheets
- information booklets
- or energy labels KitchenAid 42
All of them are important, but the most important information from the point of view of use of the device are in the user manual KitchenAid 42.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals KitchenAid 42, service manual, brief instructions and user manuals KitchenAid 42. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product KitchenAid 42.

Similar manuals

A complete manual for the device KitchenAid 42, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use KitchenAid 42 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of KitchenAid 42.

A complete KitchenAid manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual KitchenAid 42 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the KitchenAid 42, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the KitchenAid 42, that we can find in the current document
3. Tips how to use the basic functions of the device KitchenAid 42 - which should help us in our first steps of using KitchenAid 42
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with KitchenAid 42
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of KitchenAid 42 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning KitchenAid 42?

Use the form below

If you did not solve your problem by using a manual KitchenAid 42, ask a question using the form below. If a user had a similar problem with KitchenAid 42 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)