English dropdown-ico

Manual Niles Audio MSU250

24 pages 0.73 mb
Download

Go to site of 24

Summary
  • Niles Audio MSU250 - page 1

    INFRARED MAIN SYSTEM UNIT MSU 250 INST ALLA TION GUIDE B LENDING H IGH F IDELITY A N D A RCHITECTURE ® ...

  • Niles Audio MSU250 - page 2

    CONGRA TULA TIONS! Thank you for choosing MSU-250 infrared (IR) extender system from Niles. With proper installa- tion and operation, you should enjoy years of trouble-free use. Niles manufactures the industry’ s most complete line of custom installation components and accessories for audio/video systems. T o see the complete Niles product assort ...

  • Niles Audio MSU250 - page 3

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI – 305-238-4373 1 INTRODUCTION The MSU-250 an infrared (IR) extender system enables you to control your IR remote controlled A/V equipment from a remote location. This enables you to place your A/V components out of sight (behind cabinet doors, in the rear of a room, or in a different room) and still co ...

  • Niles Audio MSU250 - page 4

    2 FEA TURES AND BENEFITS The MSU250 offers a number of improvements over other IR Extender Main System Units: • Universal system—compatible with virtually all brands of A/V equipment and remote controls • Accommodates two IR sensors or keypads • Provides five flasher outputs via convenient 3.5mm jacks • System feedback LED confirms operat ...

  • Niles Audio MSU250 - page 5

    12VDC power supply (supplied with the MSU250 Main System Unit) plugged into an unswitched AC outlet powers the system Power , IR da ta, status signal and ground via CA T -5 wire 12VDC power supply (Not Supplied) plugged into the switched outlet Niles stock# FG00665 WS110 IR Sensor Niles IR Flasher Stereo Receiver Figure 1 Connecting the WS110 to a ...

  • Niles Audio MSU250 - page 6

    1. 12VDC Jack – Provides 12 volt DC power to MSU via a regulated power supply 2. IR Flasher Outputs – 3.5mm jacks provide output for either single or dual (MF1, MF1VF , MF2, MF2VF) low-level flashers 3. 3-30V AC/DC Status – 3.5mm jack provides system status to sensors/ k eypads via a 12V power supply attached to a switched outlet on the syste ...

  • Niles Audio MSU250 - page 7

    5. Status/IR Confir mation LED – This LED performs two functions: (1) it provides a visible indication of system status via a green LED and (2) confirms the reception of IR data via a blinking blue LED 6. Flasher Hi/Lo switch – Setting these switches to the appropriate position allows you to connect either a high output flooding flasher (IRB1) ...

  • Niles Audio MSU250 - page 8

    INST ALLA TION CONSIDERA TIONS (CONTINUED) WIRING From every IR Sensor location you must “home-run” a CA T -5 cable back to the MSU250. Home run means that an individual cable is connected between each IR Sensor and the MSU250 (Figure 4). 6 (CONTINUED ON NEXT P AGE) TECH TIP W IRE SIZE IS EXPRESSED BY ITS AWG (A MERICAN W IRE G AUGE ) NUMBER ? ...

  • Niles Audio MSU250 - page 9

    Figure 5 An IR sensor cable is “daisy-chained” from an IntelliPad, to a sensor and back to the MSU250 INST ALLA TION CONSIDERA TIONS (CONTINUED) INTELLIP AD WIRING When you are placing both a IntelliPad and a sensor (or two keypads) in one room you may “daisy- chain” using a single cable. A cable is run between the keypad and the sensor and ...

  • Niles Audio MSU250 - page 10

    T INST ALLA TION TOOLS REQUIRED • 1/8” (0.3cm) Standard Slotted Screwdriver • Wire Stripper INST ALLA TION Before you begin, make sure that the sensor/keypad cables, the flasher cables and the 12VDC power supply cable will all reach the proposed location of the MSU250. Mark the cables with labels describing where the cable originates (rather ...

  • Niles Audio MSU250 - page 11

    T INST ALLA TION (CONTINUED) 1. Connect and test the power supply . If it tests OK, unplug the connector from the power socket and proceed A) Plug the supplied 12VDC power supply into an unswitched 120 volt AC outlet, 50-60 HZ B) Plug the connector into the sock et marked “Power” on the MSU250 C) If the Power LED does not light, test the unswit ...

  • Niles Audio MSU250 - page 12

    INST ALLA TION (CONTINUED) 3. T est for shorts and interference . A) Reconnect the power supply . If the power LED lights and the IR test LED stays off, unplug the connector from the power socket and proceed to Step 4. The following LED conditions show a fault: • If power LED is off there is a short between +12V and GND • If IR test LED is on o ...

  • Niles Audio MSU250 - page 13

    OPERA TION TESTING THE IR EXTENDER SYSTEM TESTING THE IR EXTENDER SYSTEM T est your IR extender system by following the three principal guidelines: 1. All components can be operated. T est all of your remote controls for all of your equipment 2. Operation is consistent. A good test is to repeatedly step from pause to play with your VCR, CD , DVD , ...

  • Niles Audio MSU250 - page 14

    OPERA TION Example include: • Dropping a motorized screen • Activating a television lift • T urning on a voltage controlled switching device (e .g.: Niles AC-3 voltage controlled switched outlet) INST ALLA TION Simply plug a cable with a 3.5mm plug (tip=positive, sleeve=ground) into the jack labeled “12VDC/200mA OUTPUT”. Connect the other ...

  • Niles Audio MSU250 - page 15

    OPERA TION (CONTINUED) connected to one of your sensor wires will display the power status of your system. POWER ST A TUS — INST ALLA TION CONSIDERA TIONS PROPER POWER SUPPL Y If status is being supplied from a switched outlet you must connect a Niles 12VDC wall ada pter (Niles FG00665) into the switched AC power outlet of the preamp/receiver in ...

  • Niles Audio MSU250 - page 16

    OPERA TION (CONTINUED) 14 12VDC Power supply (Not Supplied) plugged into a switched outlet Niles stock# FG00060A Infrared Sensors MSU250 Main System Unit IRH610 Expansion Hub Figure 9 Wiring diagram for expanding a system using the IRH610 Infrared Expansion Hub. ...

  • Niles Audio MSU250 - page 17

    TROUBLESHOOTING TROUBLESHOOTING GUIDELINES There are three basic problems which prevent proper operation. In the order of probability the problems are: 1. Bad Connections or Wiring If the connections or wiring are wrong, loose, shorted or open the system will not operate properly . The symptoms could include: Power LED flickers or is off, IR test ...

  • Niles Audio MSU250 - page 18

    TROUBLESHOOTING (CONTINUED) 1. Move the sensor or the sensor cable away from the EMI source or move the source of the EMI away from the sensor or the cable 2. Connect the sensor ’ s GND terminal to true earth ground (if this isn’t feasible use the main system unit’ s GND terminal) 3. Optical Feedback Loop If you have an IR sensor in the same ...

  • Niles Audio MSU250 - page 19

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI – 305-238-4373 17 SPECIFICA TIONS IR System Compatible with virtually all brands of remotes using carrier frequencies between 26 and 105kHz. Wiring Requirements Individual home-runs of CA T -5 cable from each sensor/keypad. Unit Dimensions 5-11/16” wide x 1-1/4” high x 2” deep (173.3cm wide x 38c ...

  • Niles Audio MSU250 - page 20

    Using the MSU250 with the IntelliControl Home Theater automation system When connecting an MSU flasher output to an IntelliControl “Home Theater” port, a 150-Ohm resis- tor must be placed between the data and the ground line of the IntelliControl IR sensor input (see figure above). No resistor is needed if the MSU is being connected to the ? ...

  • Niles Audio MSU250 - page 21

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI – 305-238-4373 19 NOTES __________________________________________________________________________ __________________________________________________________________________ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ...

  • Niles Audio MSU250 - page 22

    20 LIMITED W ARRANTY NI LE S A UDI O C OR PO R ATI ON ( “N IL E S” ) WA RR A N TS I T S AC TI V E P ROD U CT S T O TH E O RIG I NA L P UR CH A SE R T O BE F RE E O F MA N UF AC TU RI NG D EF E CT S IN M ATE RI A L A ND W OR K MA N SH IP F OR A P E RI OD O F T WO Y E A RS F RO M DATE O F PU RC H AS E . TH IS WAR R A NT Y IS SU B JE CT TO TH E F ...

  • Niles Audio MSU250 - page 23

    NILES AUDIO CORPORA TION – 1-800-BUY -HIFI – 305-238-4373 21 DET ACH HERE AND RETURN TO: NI LES AUDIO CORPORA TION WARRAN TY REGISTRA TION DEPT . P .O. BOX 160818 MIAMI, FLORIDA 33 116-0818 Age: ❍ Under 25 ❍ 25-34 ❍ 35-44 ❍ 45-54 ❍ 55 & over Income: ❍ Under $24,999 ❍ $25,000-$34,999 ❍ $35,000-$44,999 ❍ $45,000-$59,999 ❍ ...

  • Niles Audio MSU250 - page 24

    Niles Audio Corporation 12331 S.W . 130 Street Miami, Florida 33186 1-305-238-4373 1-800-BUY -HIFI – www.nilesaudio.com ©2007 Niles Audio Corporation. All rights reserved. Niles, the Niles logos and Blending High Fidelity and Architecture are registered trademarks of Niles Audio Corporation. All other trademarks are the property of their respect ...

Manufacturer Niles Audio Category Universal Remote

Documents that we receive from a manufacturer of a Niles Audio MSU250 can be divided into several groups. They are, among others:
- Niles Audio technical drawings
- MSU250 manuals
- Niles Audio product data sheets
- information booklets
- or energy labels Niles Audio MSU250
All of them are important, but the most important information from the point of view of use of the device are in the user manual Niles Audio MSU250.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Niles Audio MSU250, service manual, brief instructions and user manuals Niles Audio MSU250. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Niles Audio MSU250.

Similar manuals

A complete manual for the device Niles Audio MSU250, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Niles Audio MSU250 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Niles Audio MSU250.

A complete Niles Audio manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Niles Audio MSU250 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Niles Audio MSU250, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Niles Audio MSU250, that we can find in the current document
3. Tips how to use the basic functions of the device Niles Audio MSU250 - which should help us in our first steps of using Niles Audio MSU250
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Niles Audio MSU250
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Niles Audio MSU250 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Niles Audio MSU250?

Use the form below

If you did not solve your problem by using a manual Niles Audio MSU250, ask a question using the form below. If a user had a similar problem with Niles Audio MSU250 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)