English dropdown-ico

Manual Ryobi CSB142LZ

24 pages 7.08 mb
Download

Go to site of 24

Summary
  • Ryobi CSB142LZ - page 1

    SA VE THIS MANUAL FOR FUTURE REFERENCE Y our circular saw has been engineer ed and manufactured to our high standar d for dependability , ease of operation, and operator safety . When properly car ed for , it will give you years of rugged, trouble-fr ee performance. WARNING: T o r educe the risk of injury , the user must read and understand the ope ...

  • Ryobi CSB142LZ - page 2

    2  Introduction ..................................................................................................................................................................... 2  W arranty ..................................................................................................................................................... ...

  • Ryobi CSB142LZ - page 3

    3 WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury . The term “power tool” in all of the war n- ings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SA VE THESE INSTRUCTIONS WORK AREA SAFETY  K ...

  • Ryobi CSB142LZ - page 4

    4  DANGE R! Keep hands away fr om cuttin g are a and the blade. Keep your second hand on auxiliary handle or motor housing. If both hands are holding the saw , they cannot be cut by the blade.  D o n o t r e a c h u n d e r n e a t h t h e w o r kp i e ce . Th e guard cannot protect you fr om the blade below the workpiece.  Adjust the cutt ...

  • Ryobi CSB142LZ - page 5

    5 not touch the blade or any other part, in all angles and depths of cut.  Check the operation of the lower guar d spring. If the guard and the spring ar e not operating properly , they must be serviced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris.  Lower guard should be retracted ...

  • Ryobi CSB142LZ - page 6

    6 SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the pr oduct better and safer . V V olts V oltage A Amperes Current Hz Hertz Frequency (cycles per second) W W att Power min Minutes Time Alternating Current T ype of curren ...

  • Ryobi CSB142LZ - page 7

    7 SYMBOLS SERVICE Servicing r equires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts. WARNING: T o a voi d se rio us pers ona l inj ury , do not atte ...

  • Ryobi CSB142LZ - page 8

    8 EXTENSION CORDS When using a power tool at a considerable distance fr om a power sour ce, be sur e to use an extension cor d that has the capacity to handle the current the product will draw . An undersized cord will cause a dr op in line voltage, r esulting in overheating and loss of power . Use the chart to determine the minimum wir e size r eq ...

  • Ryobi CSB142LZ - page 9

    9 45 51.5 30 15 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS  Blade Diameter ................................................. 7-1/4 in.  Blade Arbor ........................................................... 5/8 in.  Cutting Depth at 0° ........................................... 2-3/8 in.  Cutting Depth at 45° ............. ...

  • Ryobi CSB142LZ - page 10

    10 FEA TURES KNOW YOUR CIRCULAR SAW See Figure 1. The safe use of this pr oduct r equires an understanding of the information on the pr oduct and in this operator’ s manual as well as a knowledge of the project you ar e attempting. Before use of this pr oduct, familiarize yourself with all operating features and safety rules. BLADE WRENCH STORAGE ...

  • Ryobi CSB142LZ - page 11

    11 ASSEMBL Y WARNING: A 7-1/4 in. blade is the maximum blade capacity of the saw . Also, never use a blade that is too thick to allow out er blad e washe r to engag e with the fl at on the spindl e. Lar ge r blades will c ome in contac t with the blade guard s, while thicker blades will prevent blade screw from se- curing blade on spindle. Either ...

  • Ryobi CSB142LZ - page 12

    12 raiSeD LiP SCrew Fig. 6 ASSEMBL Y NOTE: Never use a blade that is too thick to allow the “D” washer to engage with the flat on the spindle. REMOVING BLADE See Figures 2 - 4.  Unplug the saw .  Depress and hold spindle lock button.  Remove blade screw by turning it counterclockwise with the blade wrench, while keeping the s ...

  • Ryobi CSB142LZ - page 13

    13 WARNING: Do not allow familiarity with this product to make you ca r ele ss . Re mem be r that a ca re le ss fra cti on of a sec ond is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thr own into your eyes ...

  • Ryobi CSB142LZ - page 14

    14 OPERA TION   Inspect the workpiece for knots or nails before cutting. Never saw into a knot or nail.  Make straight cuts. Always use a straight edge guide when rip cutting. This helps prevent twisting the blade.  Use clean, sharp, and properly set blades. Never make cuts with dull blades.  Support the workpiece properl ...

  • Ryobi CSB142LZ - page 15

    15 OPERA TION If at any time the lower blade guard does not snap closed, unplug the saw from the power supply . Exercise the lower guard by moving it rapidly back and forth fr om the full open position to the closed position several times. Normally this will restor e the guard to its normal operating condition. If it does not correct a slow or slug ...

  • Ryobi CSB142LZ - page 16

    16 OPERA TION 45 51.5 30 15 Fig. 15 45 51.5 30 15 USING THE LASER GUIDE See Figure 14. WARNING: Do not star e into the l aser beam or turn th e laser on when the tool is not in use. Failure to heed this war ning could result in possible serious personal injury . The laser guide will generate a r ed laser beam on the work surface in front of the saw ...

  • Ryobi CSB142LZ - page 17

    17 OPERA TION OPERA TING THE SAW See Figures 16 - 18. It is important to understand the corr ect method for operat- ing the saw . Refer to the figur es in this section to learn the correct and incorr ect ways for handling the saw . WARNING: T o make sawing easier and safe r , always mai ntain proper control of the saw . Loss of control could cause ...

  • Ryobi CSB142LZ - page 18

    18 OPERA TION LENGTH OF CUT SCALE See Figure 19. The saw is equipped with a length of cut scale on its base. It is parallel with the saw blade and can be used to measure the distance into the material the blade cuts. NOTE: Six inches is th e ma ximum length of cut that you can measure. Also, it is accurate only when the depth of cut is set at full ...

  • Ryobi CSB142LZ - page 19

    19 OPERA TION TO ADJUST BEVEL SETTING See Figure 23.  Unplug the saw .  Loosen bevel adjustment knob.  Raise motor housing end of saw until you r each desired angle setting on bevel scale.  Tighten bevel adjustment knob securely . WARNING: Attempting a bevel cut without having the bevel ad- justment knob securely tightened c ...

  • Ryobi CSB142LZ - page 20

    20 OPERA TION 45 51.5 30 15 Fig. 25 POCKeT CuT LOwer BLaDe guarD LOwer BLaDe guarD HaNDLe POCKET CUTTING See Figure 25. WARNING: Always adjust bevel setting to zero before making a pocket cut. Attempting a pocket cut at any other setting can result in loss of contr ol of the saw possibly causing serious injury .  Adjust the bevel setting to z ...

  • Ryobi CSB142LZ - page 21

    21 Fig. 26 BeVeL aDJuSTMeNT KNOB BLaDe COMBiNa TiON SQuare aDJuSTiNg SCrew Hex NuT 0° BeVeL STOP 51.5 15 30 45 OPERA TION 0° BEVEL STOP See Figure 26. The saw has a 0° bevel stop that has been factory adjusted to assure 0° angle of the saw blade when making 90° cuts. T o check 0° bevel stop:  Unplug the saw .  Place the saw in an ...

  • Ryobi CSB142LZ - page 22

    22 aDJuSTiNg SCrew Fig. 28 LaSer BarreL Fig. 29 LaSer BarreL 15 30 51.5 45 D AN G ER A VOID EXPOSURE Laser radiation when open, avoid direct eye exposure. Las er ra dia tio n is emi tte d fro m thi s ape rtu re. ADJUSTMENTS Fig. 27 WARNING: Be for e perf orm in g any adju stm ent , ma ke su re the pro duc t is unplugged from the power supply and th ...

  • Ryobi CSB142LZ - page 23

    23 MAINTENANCE Electric tools used on fiber glass material, wallboar d, spack- ling compounds, or plaster ar e subject to accelerated wear and possible prematur e failure because the fiber glass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently , we do not recommend using this pr oduct for extended work ...

  • Ryobi CSB142LZ - page 24

    CSB142LZ OPERA TOR’S MANUAL 7-1/4 in. LASER CIRCULAR SA W DOUBLE INSULA TED CSB142LZ 987000-328 7-9-08 (REV :02) • P AR TS AND SER VICE Prior to requesting service or purchasing replacement parts, please obtain your model and serial number from the pr oduct data plate. • MODEL NUMBER • SERIAL NUMBER • HOW TO OBT AIN REPLACEMENT P AR TS: R ...

Manufacturer Ryobi Category Saw

Documents that we receive from a manufacturer of a Ryobi CSB142LZ can be divided into several groups. They are, among others:
- Ryobi technical drawings
- CSB142LZ manuals
- Ryobi product data sheets
- information booklets
- or energy labels Ryobi CSB142LZ
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ryobi CSB142LZ.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ryobi CSB142LZ, service manual, brief instructions and user manuals Ryobi CSB142LZ. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ryobi CSB142LZ.

Similar manuals

A complete manual for the device Ryobi CSB142LZ, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ryobi CSB142LZ by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ryobi CSB142LZ.

A complete Ryobi manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ryobi CSB142LZ - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ryobi CSB142LZ, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ryobi CSB142LZ, that we can find in the current document
3. Tips how to use the basic functions of the device Ryobi CSB142LZ - which should help us in our first steps of using Ryobi CSB142LZ
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ryobi CSB142LZ
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ryobi CSB142LZ in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ryobi CSB142LZ?

Use the form below

If you did not solve your problem by using a manual Ryobi CSB142LZ, ask a question using the form below. If a user had a similar problem with Ryobi CSB142LZ it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)