English dropdown-ico

Manual EverFocus EZN850

58 pages 3.44 mb
Download

Go to site of 58

Summary
  • EverFocus EZN850 - page 1

    EZN850 User ’ s Manual Copyright © EverFocus Electronics Corp, Release: Dec. 2009 Rev .C ...

  • EverFocus EZN850 - page 2

    EZN850 2 Product Name: EZN850 EverFocus IP Network Cameras Model Number(s): EZN850 FCC Notice "Declaration of Conformity Information" This equipment has been tested and found to co mply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These lim its are design ed to provide reasonable protection against h ...

  • EverFocus EZN850 - page 3

    EZN850 3 About this document All the safety and operating instructions should be read and followed b efore the unit is operated. This manual should be retained for future reference. The information in this manual was current wh en published. The manufacturer reserves the right to revise and improve its products . All specifications are therefore su ...

  • EverFocus EZN850 - page 4

    EZN850 4 this appliance is 24V AC or 100V AC~240V AC. Use only the recommended pow er supplies. Power supplies must co mply with the requirement of the latest ver sion of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard. Electrostatic-sens itive device. Use proper CMO S/MOSFET handing precautions to avoid electrostatic ...

  • EverFocus EZN850 - page 5

    EZN850 5 T ABLE OF CONTENTS 1. INTRODUCTION.......................................... .......................................................... 6 2. FEA TURES.... ........................................................................................................... 6 3. ACCESSING THE CAMERA MENU ............................................... ...

  • EverFocus EZN850 - page 6

    EZN850 6 1. INTRODUCTION EZN850 network camera utilizes H.264, MPEG-4 and MJPEG compression for multiple streaming outputs. Engineered with the advanced new generation 16-bit DSP , the EZN850 has powerful processing cap ability to perform 560 TVL of horizontal resolution. W ith built-in DNR (Dy namic Noise Reduction), EZN850 provides crystal clear ...

  • EverFocus EZN850 - page 7

    3. ACCESSING THE CAMERA MENU Ste p 1. Start an Internet Explorer browser . Ste p 2. Enter the IP a ddress or host name of the camera in the Location/A ddress field of your browser . (Please refer to EZN850 Installation Guide for how to find the IP address). Step 3. Input “Username” and “Password”. Default Username is “user1” and d e f a ...

  • EverFocus EZN850 - page 8

    EZN850 8 are 7 section s: [Sy stem Info ], [User Config], [N etwork ], [V ideo], [User], [Ev ent] and [System]. Please refer to “4. Setti ng” for further information. ○ 3 Press button to close EZN850 network page. ○ 4 V ideo Stream Select V ideo S tream from Stream 1, St ream 2, Stream 3 and St ream 4. Please re fer to “4.4.1 Multi S tre ...

  • EverFocus EZN850 - page 9

    EZN850 9 ○ 8 Snapshot The Snapshot button saves a snapshot of the video image currently being displayed. The location where th e snapshot data is saved can be sp ecified in S etting -> User ’ s Config. Please refer to “4.2 User Config” for further information. ○ 9 Manual Control – T rigger Event Press “T rigger Event” button to t ...

  • EverFocus EZN850 - page 10

    EZN850 10 ...

  • EverFocus EZN850 - page 11

    EZN850 11 4.1 System Info System information and system log check of the setup menu can be performed on this page. The “System Info” page has 2 tabs: [Information] tab and th e [Log] tab. 4.1.1 Information System Information: Firmware version, MAC address, V ideo T y pe, Model number . (unchangeable, for reference only) ...

  • EverFocus EZN850 - page 12

    EZN850 12 4.1.2 Log System Log : Date/Time : displaying date and tim e of the log. Log message : all information and event message, including login, user ’ s IP , reboot, firmware upgrade, load factory default, configuration reset and event detected. System will keep the latest 256 records. Press button to export sy stem log into “.txt ” file ...

  • EverFocus EZN850 - page 13

    EZN850 13 4.2 User Config Live view configuration is to b e set by user . Ea ch login user can make his/her own settings for the following items: Te x t S e t t i n g Check the box for text of Machine name , Date/Time or Frame Ra te to be displayed on the screen. Te x t C o l o r Foreground Color: Select the foreground color of text to be displayed ...

  • EverFocus EZN850 - page 14

    EZN850 14 T ime Form at: 24 Hours or 12 Hours. Press Apply to apply the setting changes or Reset to reset without saving the change. Recording/Snapshot Exp ort Setting Enable Event Record ing to PC: Allow event video recorded to users' PC i f any events have been se t to record to PC. Export folder: Select Export folder by clicking on button, ...

  • EverFocus EZN850 - page 15

    EZN850 15 Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3 Network The network settings and the settings relating to Network, DDNS, Bandwidth, SMTP/FTP and Network A larm can be configured on this page. The "Network setup" page has 5 tab s: the [Network] tab, the [DDNS] tab, the [SMTP/FTP] tab and ...

  • EverFocus EZN850 - page 16

    EZN850 16 IP Setting IP T ype DHCP: Configure the DHCP server not to assign the same IP addresses used for the other network cameras and PCs w hose IP address is unique. Refer to the network ad ministrator for the settings of the server. Defa ult: DHCP. Static IP: User can manually set th e static IP for net work connection. PPPoE: This is a DSL co ...

  • EverFocus EZN850 - page 17

    EZN850 17 Password Enter Password of the account (used only for PPPoE). Press Apply to apply the setting changes or Reset to reset without saving the change. Port Setting HTTP Port Port number for HTTP/WEB communication. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.3.2 DDNS DDNS setting When accessing the ...

  • EverFocus EZN850 - page 18

    EZN850 18 server. We offer 4 DDNS server providers as foll ow: ○ www .everfocusddns.com ○ www .sitelutions.com ○ www .dyndns.com ○ www .no-ip.c om Enable: Check the box to enable DD NS setting. Service ISP: If you choose EverFocus DDNS server , you can obtain a free account na me f r om Eve rF o cus ” www .everfocusddns.com ”. E n t e r ...

  • EverFocus EZN850 - page 19

    EZN850 19 Bandwidth Setting Max. Bandwidth: Specify , Unlimited / 64 K/ 12 8 K/ 256 K / 512 K / 1M / 2M / 4M / 8M bps. the maxi mum bandwidth that the camer a is allowed to use on th e network. This is a useful function when connecting the ca mera to busy or heavily loaded networks. The default setting is Unli mited. Max. Client Limit: enter a valu ...

  • EverFocus EZN850 - page 20

    EZN850 20 send e-mails . SMTP Port: Enter the port number for SMTP . Default is 25. Authentication: Check the box, if the SMTP server re quires Authentication (user/ password). User name: Input the login user ID if th e SMTP server requires Authentication. Password: Input the password if the S MTP server requires Authentication. Receiver Address: I ...

  • EverFocus EZN850 - page 21

    EZN850 21 4.3.5 Network Alarm (reserved for PowerCon) Set Network A larm This function is reserved for PowerCon software, for th e detail setting please refer to PowerCon network alarm protocol. 4.4 V ideo The settings relating video such as streaming, camera OSD can be configured on this page. The "Video" page has 2 tabs: the [Mu lti-str ...

  • EverFocus EZN850 - page 22

    EZN850 22 4.4.1 Multi S tr eaming St ream Setting The system can output 4 video stream s simultaneously . For each of them, user can set compression for mat, resolution, quality and frame rate individually . S tream 1 is always enabled for live view . Check “Enable” box to enable other streams. Format: Select encode format from H.264, MPEG4 and ...

  • EverFocus EZN850 - page 23

    EZN850 23 Press Apply to apply the setting changes or Reset to reset without saving the change. V ideo Recording Setting User can set video recording by selecting one of the enabled video streams. This will allow user to view live images as well as to record video of the other video streaming. V ideo Stream : Select video recordin g stream from any ...

  • EverFocus EZN850 - page 24

    EZN850 24 T o ad just the viewin g range, press “++” , “+” sign of Zo om to zoom out, and “-“ , “--“ sign of Zoom t o zoom in. Press “++”, “+“, “-“ or “--“ s ign to set Focus manually . OSD setting : Use the following buttons on the operation p anel to operate the "Camera OSD setting" through a PC. (Please ...

  • EverFocus EZN850 - page 25

    EZN850 25 2. Please click SET key for saving setting and return to the previous menu. 4.4.2.2 SHUTTER 1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “SHUTTER” by clicking the DO WN ( d ) key . 2. Select the shutter mode by clicking th e LEFT ( e ) or RIGHT ( f ) key . Three modes are avai lable. FLK, ESC ...

  • EverFocus EZN850 - page 26

    EZN850 26 Ö ESC: (Reserved). Ö Manual: (Reserved). 3. Click the SET key when you finish all the settings. 4.4.2.3 WHITE BALANCE Contr ol The screen color can be adjus ted by using the WHITE BALANCE function. 1. Please direct the arrow to point to “WHITE BAL” on the SETUP menu by clicki ng UP ( c ) or DOWN ( d ) key . 2. Please select the mode ...

  • EverFocus EZN850 - page 27

    EZN850 27 adjust the white balan ce again. Ö MANUAL: The manual adjustment mode enables a more precise adjustment. Please select A TW or A WC first. Then change to manual adjustment mode and click SET key . Set the suitable color temperatur e, and increas e or decrease the red and blue color valu es at the sa me time while checking th e color chan ...

  • EverFocus EZN850 - page 28

    EZN850 28 Ö HIGH: The gain increases from 0dB up to 42dB. Ö MIDDLE: The gain increases fro m 0dB up to 30dB. Ö LOW : The gain increases from 0dB up to 18dB. Ö OFF: BACKLIGHT fu nction does not operate. 4.4.2.5 AGC (A uto Gain Control) 1. Please direct the arrow to point to “AGC” on the SETUP menu by clicking UP ( c ) or DOWN ( d ) key . 2. ...

  • EverFocus EZN850 - page 29

    EZN850 29 Ö OFF: No reduction in noise level. Ö LOW : Little reduction in noise level with nearly no ghost image. Default value is LOW . Ö MIDDLE: Just enough reduction in noise levels without causing much ghost imaging. Ö HIGH: Huge reduction in noise level, which may cause much ghost imaging. 4.4.2.7 SENS-UP SENS UP is used to keep a brillian ...

  • EverFocus EZN850 - page 30

    EZN850 30 3. Click the SET key when you finish all the settings. 4.4.2.8 SPECIAL 1. Please direct the arrow to point to “SPECIA L” on the SETUP menu by clicking UP ( c ) or DOWN ( d ) k ey . 2. Select the mode you would like to operate by clicking LEFT ( e ) or RIGHT ( f ) key . 4.4.2.8.1 CAMERA ID Input the camera ID, and it will be appeared o ...

  • EverFocus EZN850 - page 31

    EZN850 31 3) Click the S ET key . 4) Maximum 15 letters can be used for the ID. ¾ Clicking UP ( c ), DOWN ( d ), LEFT ( e ) or RIGHT ( f ) ke y to select the letters. ¾ Click the SET key to lock in the letters. 5) Once a name has been selected, please choose a position where you would like to display the name. ¾ Move the cursor onto “POS” an ...

  • EverFocus EZN850 - page 32

    EZN850 32 4.4.2.8.2 COLOR ADJ Adjust the Color Gai n from 0 ~ 15 4.4.2.8.3 SYNC There are two SYNCHRONIZA TION modes: INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK mode, without a sy nchronous generator , it synchronizes the video signal between cameras. The Line-Lock synchronization is only used in the places o f 60Hz (NTSC models ) or 50Hz (P AL ...

  • EverFocus EZN850 - page 33

    EZN850 33 z Please sel ect the area you w ould like to detect from the 4 areas in AREA SEL mode . z Please select O N mode for the chosen are a. z Please click UP ( c ) or DOWN ( d ) key to m ove betwe en T OP , DOWN, LEFT and RIGHT for adjusting the size of the area. z Please click LEFT ( e ) or RIGHT ( f ) key to adjust the value for size of the ...

  • EverFocus EZN850 - page 34

    EZN850 34 2. Increase DOWN scale value by 20. AREA 1 position after change is : TOP: 10, DOWN: 45, LEFT : 20 and RIGHT : 40. 3. Increase TOP scale value by 20. AREA1 p osition after chang e is: TOP: 30, DOWN: 45, LEFT : 20 and RIGHT : 40. 4. Increase RIGHT scale value by 20. AREA 1 position after change is: T OP: 30, DOWN: 45, LEFT : 20 and RIGHT : ...

  • EverFocus EZN850 - page 35

    EZN850 35 4.4.2.8.5 PRIV ACY This mode covers the areas y ou do not want to see on the screen. 1) Please direct th e arrow to point to “PRIV ACY” by clicking UP ( c ) o r DOWN ( d ) key . 2) Select “ON” by clicking LEFT ( e ) or RIGHT ( f ) key . 3) Click the SET key . z Please select th e area you would like to cover from the 4 areas in AR ...

  • EverFocus EZN850 - page 36

    EZN850 36 1. The original position of AREA1 w as T OP: 10, DOWN: 25, LEFT : 20 and RIGHT : 40. 2. Increase DOWN scale value by 20. A REA1 position after chang e is: TOP: 10, DOWN: 45, LEFT : 20 and RIGHT : 40. 3. Increase TOP scale value by 20. AREA1 p osition after chang e is: TOP: 30, DOWN: 45, LEFT : 20 and RIGHT : 40. 4. Increase RIGHT scale va ...

  • EverFocus EZN850 - page 37

    EZN850 37 5. Increase LEFT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT : 40 and RIGHT : 60. z In order to save the ch anges and co mplete th e s e tt ing, click the SET key . This allows you to return to th e previous menu. 4.4.2.8.6 MIRROR -ON: Sets a horizontal image 180 angle inversion. -OFF: Disable the inv ersion ...

  • EverFocus EZN850 - page 38

    EZN850 38 4.4.2.8.8 RESET Click SET key on “RESET” for 3 seconds until it restarts. It will go to factory default value. 4.4.2.8.9 RETURN Click SET key on “RETURN”. It saves all settin gs in SPECIAL menu and returns to the Setup menu. 4.4.2.9 EXIT Click SET key on “EXIT” after you finish all the settings. I t will return to live image. ...

  • EverFocus EZN850 - page 39

    EZN850 39 4.5 USER User Information Maximum 10 users can be set for using the IP camera. The user information displays the authorized users and access levels: • Sup ervisor/Administrator –a supervisor/ad ministrator has unrestricted access to the Setting menu and can determine the registration of all other users. H owever, administrator is not ...

  • EverFocus EZN850 - page 40

    EZN850 40 4.6 EVENT An event in the camera is when an E vent T ype is act ivated and causes certain actions to be performed. The e vent type is the set of conditions that specifies how and when which actions will be performed. This table describes how to setup action types and event ty pe. E v e n t T y p e Action Type Alarm Input Manual Trigger Mo ...

  • EverFocus EZN850 - page 41

    EZN850 41 4.6.1 Event The settings relating to e vent occurrences such as settings for the event occurrenc e, motion, alarm and time mask can be confi gured on this page. The "Event" page has 4 tabs: the [Event] tab, the [Motion] tab , the [Alar m] tab and the [Time Mask] tab. Press button to add an event condition. T o modify the event l ...

  • EverFocus EZN850 - page 42

    EZN850 42 T o change the priority of events, click on the event and it will be high lighted. Press or button to move between even ts . The event that has highest priority will be activated first. Press Apply to apply the setting changes or Reset to reset without saving the change. This example describes how to set the camera to upload i mages to FT ...

  • EverFocus EZN850 - page 43

    EZN850 43 5. Check “Enable Pre-alarm Buf fer” and “Enable Post-alar m Buffer”. For pre-and post alarm buffer setting, please refer to “4.6.3 Alarm”. 6. Check “Enable This Event”. 7. Select “Always” for time mask. F or detail about T ime Mask, please refer to “4.6.4 T ime Mask”. 8. Click to save this event in event lis t. 4.6 ...

  • EverFocus EZN850 - page 44

    EZN850 44 2. Press to have the entire screen s elected for motion det ection. Press to clear all select ions. P ress and click on th e poly gon, to erase that poly gon. 3. You can select 5 individual motion area, which can be distinguished by 5 different colors. 4. Select color to choose the area y ou want to enable. 5. Check Enable checkbox to ena ...

  • EverFocus EZN850 - page 45

    EZN850 45 Alarm Output Setting Conta ct T ype: Norm al Clos e, Norm al Ope n Duration T ime: Select duration time of alarm output from 5 sec, 10 sec, 20 sec, 30 sec, 60 sec, 2 min, 3 min and 5 min. Press Apply to apply the setting changes or Reset to reset without saving the change. Pre/Post Alarm Setting This function is used to check what happ en ...

  • EverFocus EZN850 - page 46

    EZN850 46 4.6.4 Time Mask T ime Mask Setting T ime mask setting allows you to schedule event actions. Select Alw ays for event action to be taken continuously . Press button to add ne w time period. Mask name: Input a mask name for the new time period. Check the check box for the day to be scheduled: Sun, Mon, T ue, W ed, Thu, Fri & Sat. Set th ...

  • EverFocus EZN850 - page 47

    EZN850 47 4.7 SYSTEM Date/Time, Daylight Saving, SD card and Maintenance settings can be performed on this page. The "System" page has 4 tabs: the [Date/Time] tab, the [Day light Saving] tab, the [SD card] tab and the [Main tenance] t ab. 4.7.1 Date/Time Machine Name Setting Machine Nam e: Enter the name of the camera. The ent ered name w ...

  • EverFocus EZN850 - page 48

    EZN850 48 T ime: Click on Hour , Minute, Seconds, am/pm; then use up arrow to increase value and down arrow to decrease val ue. Press Apply to apply the setting changes or Reset to reset without saving the change. Set Date/T ime Sync. Check Enable NTP c heckbox to enable NTP server . NTP server: Time automati cally adjusted by synchronizing with NT ...

  • EverFocus EZN850 - page 49

    EZN850 49 4.7.2 Daylight Saving Set Daylight Saving Check Enable Daylight Saving checkbox to enable day light saving. Set the start time to daylight sav ing time. Set the start week of day light saving ti me: 1 st / 2 nd / 3 rd / 4 th / Last Set the start date of daylight saving time: S unday / Monday / T uesday / W ednesday / Thursday / F riday / ...

  • EverFocus EZN850 - page 50

    EZN850 50 “End” time when daylight saving ends. Press Apply to apply the setting changes or Reset to reset without saving the change. 4.7.3 SD Card Setup SD Card Notification: Notification will be made via e- mail when the remaining space of the SD memory card re ached the valu e selected from the followi ng. 50%, 20%, 10%, 5%, 2%, 0% Event Rec ...

  • EverFocus EZN850 - page 51

    EZN850 51 -Normal: Follow the event actions settings you have made in “Event” menu to record event video to SD c ard. -Overwrite: Select ON for ov erwriting data when SD card memory is full. Select OFF for not overwriting SD card data. Press Apply to apply the setting changes or Reset to reset without saving the change. SD Card Utility The tota ...

  • EverFocus EZN850 - page 52

    EZN850 52 3. Enter administrator user name and password. (user1, 11111111) 4. Then you can download video or image file from SD card. The file name will show the time of video. ...

  • EverFocus EZN850 - page 53

    EZN850 53 4.7.4 Serial Commun ication RS485 Setting Camera ID: This entry is used to assign ca mera own ID code. Baud Rate: This field is to set the speed at whi ch is used to trans mit instruction or information through the RS485 port on the camera. There are six different speeds, 2400/4800/9600/19200/38400/57600. The d efault setting from the fac ...

  • EverFocus EZN850 - page 54

    EZN850 54 Pres s Apply to apply the setting chan ges or Reset to reset without saving the change. 4.7.5 Maintenance Maint enance Se rver Reboot: The unit is rebooted without changing any of the settings. Use this method by pressing Reboot button if the unit is no t behaving as expected. Restore: The unit is restarted and most current settings are r ...

  • EverFocus EZN850 - page 55

    EZN850 55 Save/Load Configuration Server To take a backup o f all of the conf igurations, pres s Save to save all configurations to a config. file. If necess ary, it is then poss ible to return to the prev ious settings if the settings are changed and there is unexp ect ed beh avio r . Press the Browse bu tton to locate the saved config. file (see ...

  • EverFocus EZN850 - page 56

    EZN850 56 5. SPECIFICA TIONS CAMERA Pick up De vic e 1/3" Sony sup er HA D CCD Pixel Ef fective NTSC: 768 (H) x 494 (V); P AL: 752 (H) x 582 (V) Sensitivity 0.002 L ux / F=1. 2 (IR Off, SE NS-UP 128x ) 0 Lux (IR On) Day & Nigh t T rue Day/N ight with IR cut filter Lens V ari-focal 6~50mm, 9x optical zoom Video Output BNC socket, composite ...

  • EverFocus EZN850 - page 57

    EZN850 57 We ight 2.5kg ; 5.5lbs (3.0kg ; 6.6LBS with b racket) ENVIRONMENT AL Operating T emp. -40°C ~ 50°C ; -40°F ~ 1 22°F Humi dity 20~8 0% Heat er Y es Weather proof Rat ings IP66 V andal Proof Y es ...

  • EverFocus EZN850 - page 58

    EZN850 58 EverFocus Electr onics Corp. Head Office: 12F , No.79 Sec. 1 Shin-T ai W u Road, Hsi-Chih, T aipei, T aiwan TEL: +886-2-26982334 F AX: +886-2-26982380 www .everfocus.com.tw USA L.A. Office: 1801 Highland A ve. Unit A Duarte, CA 9 1010, U.S.A. TEL: +1-626-844-8888 F AX: +1-626-844-8838 www .everfocus.com USA N.Y . Office: 415 Oser A venue ...

Manufacturer EverFocus Category Security Camera

Documents that we receive from a manufacturer of a EverFocus EZN850 can be divided into several groups. They are, among others:
- EverFocus technical drawings
- EZN850 manuals
- EverFocus product data sheets
- information booklets
- or energy labels EverFocus EZN850
All of them are important, but the most important information from the point of view of use of the device are in the user manual EverFocus EZN850.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals EverFocus EZN850, service manual, brief instructions and user manuals EverFocus EZN850. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product EverFocus EZN850.

Similar manuals

A complete manual for the device EverFocus EZN850, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use EverFocus EZN850 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of EverFocus EZN850.

A complete EverFocus manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual EverFocus EZN850 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the EverFocus EZN850, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the EverFocus EZN850, that we can find in the current document
3. Tips how to use the basic functions of the device EverFocus EZN850 - which should help us in our first steps of using EverFocus EZN850
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with EverFocus EZN850
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of EverFocus EZN850 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning EverFocus EZN850?

Use the form below

If you did not solve your problem by using a manual EverFocus EZN850, ask a question using the form below. If a user had a similar problem with EverFocus EZN850 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)