English dropdown-ico

Manual Pelco ICS210

20 pages 1.95 mb
Download

Go to site of 20

Summary
  • Pelco ICS210 - page 1

    INST ALLA TION ICS210 Series Camclosure ® Integrated Camera System C2491M-D (8/06) ...

  • Pelco ICS210 - page 2

    2 C2491M-D (8/06) Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . ...

  • Pelco ICS210 - page 3

    C2491M-D (8/06) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, Class A (black -white, EIA and C ...

  • Pelco ICS210 - page 4

    4 C2491M-D (8/06) Description The ICS210 Series Camclosure ® is a wedge style integrated camera system that is quick and easy to install. The system is designed to mount directly to a wall or ceiling, or to a corner with the ICS210- CM corner mount. ICS210 system is shipped fully assembled. System components include a cover , base with camera and ...

  • Pelco ICS210 - page 5

    C2491M-D (8/06) 5 Installation PREPARE MOUNTING SURFACE 1. Remove the cover of the ICS210. Use the screwdriver bit that is provided to loosen the three tamperproof screws, and then lift the cover from the base. 2. Remove the camera assembly from the base by removing the Phillips screws on each side of the camera assembly (refer to Figure 2 ). Figur ...

  • Pelco ICS210 - page 6

    6 C2491M-D (8/06) 4. Select a fi xed or adjustable mounting pattern (refer to Figure 3 and Figure 4 ). Using the mounting plate as a template, mark the wire feedthrough and fastener hole positions on the mounting surface. Prepare the holes for the installation. Figure 3. Fixed Mounting Pattern Figure 4. Adjustable Mounting Pattern FIXED MOUNTING P ...

  • Pelco ICS210 - page 7

    C2491M-D (8/06) 7 INSTALL BASE WITHOUT CONDUIT 1. Pull the power and video wiring for the camera through the mounting surface and then through the wiring hole in the mounting plate. Fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length. Adjustable mounting pattern only : Adjust the ...

  • Pelco ICS210 - page 8

    8 C2491M-D (8/06) 3. Using a blunt tool push out the wiring plug in the bottom of the base (refer to Figure 6). Pull the wiring inside the base. Figure 6. Removing the Wiring Plug 4. Insert the hole plug that is supplied into the hole in the base of the Camclosure (refer to Figure 7). Figure 7. Installing the Hole Plug HOLE PLUG ...

  • Pelco ICS210 - page 9

    C2491M-D (8/06) 9 5. Pull wiring through the conduit opening (refer to Figure 8): a. Use a 1/16” hex head wrench to loosen the hex head inset screw . b. Use a screwdriver to remove the conduit cover. c. Pull the power wires and video cable through the conduit opening. Figure 8. Removing the Conduit Cover 6. Install a 0.75-inch (1.91 cm) conduit c ...

  • Pelco ICS210 - page 10

    10 C2491M-D (8/06) REINSTALL CAMERA MODULE Reinstall the camera module. Refer to Figure 9 . Make sure the top of the camera is oriented properly . On the lens housing, look for the label that says TOP . Figure 9. Camera Installation ADJUST POSITION 1. T urn on power to the camera and monitor . 2. V arifocal lens only: Loosen the focal length and fo ...

  • Pelco ICS210 - page 11

    C2491M-D (8/06) 11 REPLACE COVER Place the cover of the ICS210 onto the base of the unit. Using the screwdriver bit (supplied), tighten the three tamperproof screws. NOTE: Remove the foam from the inside of the cover before installing the cover . ...

  • Pelco ICS210 - page 12

    12 C2491M-D (8/06) Adjustments (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iris level, focus, or switch settings (refer to proc ...

  • Pelco ICS210 - page 13

    C2491M-D (8/06) 13 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fi xed focal length lens with an auto iris, you can adjust the iris level setting to increase or decrease brightness. Figure 12. Iris Level Adjustment FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS T o adjust the focus, do the following: 1. Loosen the lockin ...

  • Pelco ICS210 - page 14

    14 C2491M-D (8/06) HEATER BOARD REMOVAL T o remove the heater board, do the following: 1. Disconnect the four -pin heater connector (red, orange, and black wires) if it is plugged in. Figure 14. Removing Heater Board 2. Wait for the heater elements to cool if they are hot. 3. Apply pressure and press on the corner of the board. WARNING: Heater elem ...

  • Pelco ICS210 - page 15

    C2491M-D (8/06) 15 SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to Figure 15 . The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there are no bright spots that darken other picture details. M ...

  • Pelco ICS210 - page 16

    16 C2491M-D (8/06) SWITCH SETTINGS FOR V ARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. Figure 17. Switch Settings for Varifocal Lens For manually setting and locking the white balance Place a white background in front of camera and turn off switch 1. For gamma corre ...

  • Pelco ICS210 - page 17

    C2491M-D (8/06) 17 Specifications General Pan/T ilt Adjustment Manual; 5° above horizontal to 20° below horizontal tilt; 24° pan adjustment when using the adjustable mounting pattern in base Rating Meets NEMA T ype 4X and IP66 standards Construction Aluminum mounting plate, base, and cover, steel camera mounting bracket Finish Gray polyester po ...

  • Pelco ICS210 - page 18

    18 C2491M-D (8/06) REVISION HISTORY Manual # Date Comments C2491M 6/05 Orginal version. C2491M-A 7/05 Revised per new camera shell design for varifocal lens. C2491M-B 10/05 Revised switch-setting descriptions for varifocal lens. C2491M-C 1/06 Revised factory switch settings for varifocal lens. Updated wiring information. C2491M-D 8/06 Updated mount ...

  • Pelco ICS210 - page 19

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products. • Three years on Genex ® Series p ...

  • Pelco ICS210 - page 20

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands United Arab Emirates | United Kingdom | United St ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco ICS210 can be divided into several groups. They are, among others:
- Pelco technical drawings
- ICS210 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco ICS210
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco ICS210.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco ICS210, service manual, brief instructions and user manuals Pelco ICS210. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco ICS210.

Similar manuals

A complete manual for the device Pelco ICS210, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco ICS210 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco ICS210.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco ICS210 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco ICS210, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco ICS210, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco ICS210 - which should help us in our first steps of using Pelco ICS210
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco ICS210
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco ICS210 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco ICS210?

Use the form below

If you did not solve your problem by using a manual Pelco ICS210, ask a question using the form below. If a user had a similar problem with Pelco ICS210 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)