English dropdown-ico

Manual Pelco SD4N-B1

28 pages 1.94 mb
Download

Go to site of 28

Summary
  • Pelco SD4N-B1 - page 1

    INST ALLA TION C3446M (7/08) Spectra ® Mini IP Dome System ...

  • Pelco SD4N-B1 - page 2

    2 C3446M (7/08) Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description ...

  • Pelco SD4N-B1 - page 3

    C3446M (7/08) 3 List of Illustrations 1 DHCP Network Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 Endura Network Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 Private Network Exam ...

  • Pelco SD4N-B1 - page 4

    4 C3446M (7/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 7. Only use attachments/accessories specified by th ...

  • Pelco SD4N-B1 - page 5

    C3446M (7/08) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This ...

  • Pelco SD4N-B1 - page 6

    6 C3446M (7/08) Description The Spectra ® Mini IP dome system is an indoor mini do me system with a built-in 100Base-TX network interface for live streaming to a sta ndard Web browser (Microsoft ® Internet Explorer ® or Firefox ® ). The Spectra Mini IP dome features open architecture connec tivity for third-party sof tware recordin g solutions ...

  • Pelco SD4N-B1 - page 7

    C3446M (7/08) 7 PARTS LIST The following parts are supplied with the Spectra Mini IP dome system: The following parts, in addition to the normal in stallation tools, are needed but not supplied: Qty Descr iption 1 Dome driv e 1 Dome bubble with trim ring 1 Installation manual (C3446M) 1 Operation/Configur ation manual (C3447M) 1 Spring paddle flex ...

  • Pelco SD4N-B1 - page 8

    8 C3446M (7/08) BASIC SYSTEM CONFIGURATIONS The following illustrations demonstrate the possible conf igurations of Spectra Mini IP with a variety of network options. IMPORT ANT NOTE. PLEASE READ . The network implementation s in this document are shown as general representations only and are not intended to show detailed network topologies. Y our ...

  • Pelco SD4N-B1 - page 9

    C3446M (7/08) 9 DHCP NETWORK In this configuration, the DHCP network is accessed throu gh the Web browser . NOTE: For a secure network, Pelco recomme nds placing the dome behind a firewall. Refer to T able A on page 8. Figure 1. DHCP Network Ex ample ENDURA NETWORK Refer to T able A on page 8. Figure 2. Endura Network Example ...

  • Pelco SD4N-B1 - page 10

    10 C3446M (7/08) PRIVATE NETWORK When using a private network, th e PC used to operate the Web browser acts as the server . If a static IP network is being used rather than a DHCP network, t he dome system is assigned a default IP address of 192.168.0.20 on netmask 255.255.0.0. After the first dome system is plugged in and recogni zed on a static I ...

  • Pelco SD4N-B1 - page 11

    C3446M (7/08) 11 STATIC NETWORK When using a static network, the PC used to o perate the Web browser must use the same subnet mask as the dome systems to which it is connected. When the first dome system is plugged into the network, it is assigned a default IP address of 19 2.168.0.20 on netmask 255.255.0.0. After the first dome system is plugged i ...

  • Pelco SD4N-B1 - page 12

    12 C3446M (7/08) Cover and Back Box Installation The Spectra Mini IP is an indoor dome system desi gned for ceiling applicatio ns. The dome can be mounted to the surface of ceilings, or it can be recessed in hard ceilings or standard 2 x 2 ft (61 x 61 cm) tiles in suspended ceilings. SURFACE MOUNT INSTALLATION 1. Prepare the ceiling as follows: a. ...

  • Pelco SD4N-B1 - page 13

    C3446M (7/08) 13 Figure 5. Ceiling Installatio n Figure 6. Concrete Ceil ing Installation 6-32 T oggle Bolts (not supplied) #8 x 3.50-Inch Self-T appin g Screws (supplied) NOTE: Use either toggle bolts or self-tapping screws when mounting the dome to a standard ceiling. 8-32 Studs (not supplied) Nuts (not supplied) ...

  • Pelco SD4N-B1 - page 14

    14 C3446M (7/08) RECESSED INSTALLATION SUSPENDED CEILING 1. Remove the spring paddle flex assembly from the surface mount ring (refer to Figure 7). Figure 7. Spring Paddle Flex Assembly 2. Remove the surfa ce mount ring from the d ome drive as follows (refer to Figure 8 on page 15): a. Place fingers on the circular marks located on the sides of the ...

  • Pelco SD4N-B1 - page 15

    C3446M (7/08) 15 9. Line up the tabs on the trim ring with the slots in the dome drive. Snap the trim ring and dome bubble into place. Figure 8. Removing the Surf ace Mount Ring Figure 9. Recessed Installation Spring Paddle Flex Assembly #8-32 x 3.50-Inch Machine Screws 1LINE OU T + 2LINE OU T - 3LINE IN + 4LINE IN - 5AUX + 6AUX - 7ALAR M- 8ALAR M+ ...

  • Pelco SD4N-B1 - page 16

    16 C3446M (7/08) HARD CEILING 1. Remove the spring paddle flex assembly from the surface mount ring. 2. Remove the surfa ce mount ring from the d ome drive as follows (refer to Figure 8 on page 15): a. Place fingers on the circular marks located on the sides of the surface mount ring. b. Pinch the sides. c. Lift and remove the surface mount ring fr ...

  • Pelco SD4N-B1 - page 17

    C3446M (7/08) 17 Wiring T ables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connecto r . The 8-pin RJ-45 connector inclu des video and PoE for the dome system. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply; th is simplifies the installation and operati ...

  • Pelco SD4N-B1 - page 18

    18 C3446M (7/08) 24 V A C CONNECTIONS (OPTIONAL) If PoE is not used, the camera includes a 24 VAC po wer connector . Connect the power cable to the 2-pin power connector on the back of the camera using t he terminal block connector (provided). Refer to Recommended Wire Gauge and Wiring Dista nces on page 1 8. The power supply connector is shown in ...

  • Pelco SD4N-B1 - page 19

    C3446M (7/08) 19 CONNECTING ALARMS The Spectra Mini IP provides an alarm input for external signaling devices, such as door contacts or motion detectors. Both normally open and normally closed devices are supported. SUPERVISED ALARMS When an alarm is configured as a supervised alarm, Spectra Mini IP maintain s a constant electrical current through ...

  • Pelco SD4N-B1 - page 20

    20 C3446M (7/08) UNSUPERVISED ALARMS When an alarm is configured as an unsupervised alarm, the dome system only trig gers an alarm when the normal alarm state (normally open or normally closed) changes. Figure 15 shows the ala rm and no alarm conditi ons of an unsupervised alarm input. A normally closed alarm input can be defeated with a bypass; a ...

  • Pelco SD4N-B1 - page 21

    C3446M (7/08) 21 ALARM CONNECTIONS Refer to Figure 10 on page 17 for addi tional wiring information. The alarm is internally connected to th e Spectra Mini IP chassis. Do not connect directly to any potential except chassis ground. Figure 18. Unsupervise d Alarm In put Wiring Alarm Re turn: Alarm - Alarm: Alarm + ...

  • Pelco SD4N-B1 - page 22

    22 C3446M (7/08) Reset Button Use the reset button locate d underneath the tr im ri ng on the mounting flange to access the following modes: T o access one of these modes: 1. Press and hold the reset butto n. The unit starts cycling throug h the modes; hold the b utton for four seconds to access (cycle through) each mode. The unit status indicator ...

  • Pelco SD4N-B1 - page 23

    C3446M (7/08) 23 T roubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • C heck Cat5 cable connection. • V erify PoE is enabled. • Disconnect the network cable and then reconnect it to the dome system. Check the LED on the trim ring to verify that it is fl ashing green, indicating the dome system has power . Power ...

  • Pelco SD4N-B1 - page 24

    24 C3446M (7/08) Dome system not discovered No dome system power V erify the dome system is powered correctly with PoE or with 24 VAC. Confirm power consumption with Web interface of PoE-capable switch or through blinking green LED during dome system power -up. Network conflict • V erify the dome system is physically connected to the same network ...

  • Pelco SD4N-B1 - page 25

    C3446M (7/08) 25 Specifications MECHANICAL Pan Movement 360° continuous pan rotatio n V ertical T ilt Unobstructed +2° to -92° Manual Pan/Ti lt Speeds Pan 0.4-80°/sec manual operation, 100°/sec turbo T ilt 0.7-40°/sec manual ope ration Preset Speeds Pan 140°/sec T ilt 80°/sec For variable speed operation an appropriate controller is require ...

  • Pelco SD4N-B1 - page 26

    26 C3446M (7/08) LENS Lens f/1.8 (focal length, 4.2~42 mm) Zoom 10X optical zoom, 8X digital zoom Zoom Speed (optical range) 1.5/2.5/4.3 seconds Horizontal Angle of View 46.4° wide zoom 5.0° telephoto zoom Focus Automatic with manual override Iris Control Automatic with manual override (Design and product specifications subject to change without ...

  • Pelco SD4N-B1 - page 27

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, witho ut charge, any mer c handise proved defective in ma terial or wo rkmanship for a period of one year after th e date of shipment. Exception s to this warrant y are as noted below: • Five years on fiber opt ic products and TW3 000 Series unshield ed twisted pair (U ...

  • Pelco SD4N-B1 - page 28

    Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: (800) 289-9100 Fax: (800) 289-9150 International T el: +1 (559) 292-1981 Fax: +1 (559) 348-1120 www .pelco.com ISO 9001 Australia | Finland | France | Germany | Italy | Macau | The Nethe rland s | Russia | Singapore South Africa | Spain | Sweden | United Ara ...

Manufacturer Pelco Category Security Camera

Documents that we receive from a manufacturer of a Pelco SD4N-B1 can be divided into several groups. They are, among others:
- Pelco technical drawings
- SD4N-B1 manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco SD4N-B1
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco SD4N-B1.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco SD4N-B1, service manual, brief instructions and user manuals Pelco SD4N-B1. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco SD4N-B1.

Similar manuals

A complete manual for the device Pelco SD4N-B1, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco SD4N-B1 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco SD4N-B1.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco SD4N-B1 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco SD4N-B1, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco SD4N-B1, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco SD4N-B1 - which should help us in our first steps of using Pelco SD4N-B1
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco SD4N-B1
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco SD4N-B1 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco SD4N-B1?

Use the form below

If you did not solve your problem by using a manual Pelco SD4N-B1, ask a question using the form below. If a user had a similar problem with Pelco SD4N-B1 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)