-
Electrolux B 99852G - page 1
B 99852G User Manual Hob ...
-
Electrolux B 99852G - page 2
2 Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350350 Installation z This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and ...
-
Electrolux B 99852G - page 3
3 z Ensure the control knobs are in the ‘OFF’ position when not in use. z When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. z Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. z Never leave the ...
-
Electrolux B 99852G - page 4
4 This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC - 89/336 EEC - 90/396 EEC, current edition. Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions Step by step instructions for an operation Hints and T ...
-
Electrolux B 99852G - page 5
5 1. Hob T op 2. Semi-rapid Burners 3. Auxiliary Burner 4. Ultra-rapid Burner (triple crown) 5. Control knobs Description of the Hob INST ALLA TION Any gas installation must be carried out by a competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual. Ple ...
-
Electrolux B 99852G - page 6
6 Hob burners T o light a burner: z Push in the relevant control knob and turn it to maximum position. z Upon ignition, keep the knob pushed down about 5 seconds . This will allow the "thermocouple" (fig. 1 - letter D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. z Then adjust the f ...
-
Electrolux B 99852G - page 7
7 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob T o p Regularly wipe over the hob top using a soft cloth well wrung out in warm water ...
-
Electrolux B 99852G - page 8
8 Pan Supports T o keep the pan supports in the correct position, they are mounted on metal pins located in the back of the hob. After cleaning the hob, ensure the pan supports are properly placed as shown in fig. 3. The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally lea ...
-
Electrolux B 99852G - page 9
9 Something Not Working? If the hob is not working correctly , please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB ha ...
-
Electrolux B 99852G - page 10
10 Customer Care Service and Spare Parts When you contact the Service Centre, they will need the following information: 1 . Y our name, address and post code. 2 . Y our telephone number 3 . Clear and concise details of the fault 4 . The model and the serial number (see rating label on the back of this instruction booklet) 5 . Date of purchase If yo ...
-
Electrolux B 99852G - page 11
11 Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour , mate ...
-
Electrolux B 99852G - page 12
12 Instructions for the Installer Engineers technical data BURNER ULTRA-RAPID SEMI-RAPID AUXILIARY (triple crown) (medium) (small) POSITION M A X M I N M A X M I N M A X M I N NOMINAL THERMAL POWER (kW) 3 .8 1.20 1. 9 0.45 1. 0 0.33 NOMINAL FLOW RATE (m 3 /h) 0.362 0.114 0.181 0.043 0.095 0.028 NOZZLE REFERENCE 146 Adjust. 96 Adjust. 70 Adjust. (1/ ...
-
Electrolux B 99852G - page 13
13 700 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE FO 2028* FO 2027* Instructions for the Installer Important safety requirements This hob must be installed in acc ...
-
Electrolux B 99852G - page 14
14 Installation Important This hob must be installed by a competent person to the relevant Gas Standards. Any gas installation must be carried out by a registered competent person. The manufacturer will not accept liability , should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of th ...
-
Electrolux B 99852G - page 15
15 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connecti ...
-
Electrolux B 99852G - page 16
16 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under ...
-
Electrolux B 99852G - page 17
17 Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the underside outside edge of the hob. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below . 1) Remove the pan supports, the burners caps and crowns and turn the hob up ...
-
Electrolux B 99852G - page 18
18 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240 ...
-
Electrolux B 99852G - page 19
19 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break th ...
-
Electrolux B 99852G - page 20
20 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supply should now be satisfactory. Carry out: D: Resistance to Earth check. Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation che ...
-
Electrolux B 99852G - page 21
21 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . — T est leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK ...
-
Electrolux B 99852G - page 22
22 Check gas supply at burner Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check fitting of burners Check position of the electrode Check by pass simmer adjusted Light burner manually Check continuity fro ...
-
Electrolux B 99852G - page 23
23 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . 1) T urn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguis ...
-
Electrolux B 99852G - page 24
24 AEG Haugeräte GmbH Postfach 1036 D-90327 Nürnberg http://www .aeg.hausgeraete.de © Copyright by AEG Conversion from Natural Gas to LPG IMPORT ANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use w ...
-
Electrolux B 99852G - page 25
25 ...
-
Electrolux B 99852G - page 26
...
-
Electrolux B 99852G - page 27
...
-
Electrolux B 99852G - page 28
35686-0203 AM 05/06 Grafiche MDM - Forlì www .aeg-electrolux.co.uk ...
Do you have a question concerning Electrolux B 99852G?
Use the form below
If you did not solve your problem by using a manual Electrolux B 99852G, ask a question using the form below. If a user had a similar problem with Electrolux B 99852G it is likely that he will want to share the way to solve it.