English dropdown-ico

Manual Delta DP350

17 pages 0.61 mb
Download

Go to site of 17

Summary
  • Delta DP350 - page 1

    INSTRUCTION MANUAL 12" V ariable Speed Drill Pr ess (Model DP350) P ART NO. 905584 - 01-31-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ESP AÑOL: PÁGIN ...

  • Delta DP350 - page 2

    2 W oodworking can be dangerous if safe and pr oper operating procedures ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precautions ar e overlooked or ...

  • Delta DP350 - page 3

    3 17. REDUCE THE RISK OF UNINTENTIONAL ST ARTING . Make sure switch is in “OFF” position befor e plugging in power cord. In the event of a power failure, move switch to the “OFF” position. 18. NEVER ST AND ON TOOL . Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 19. CHECK DAMAGED P ARTS . ...

  • Delta DP350 - page 4

    A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cords which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connectin ...

  • Delta DP350 - page 5

    Use proper extension cor ds. Make sure your extension cord is in good condition and is a 3-wir e extension cord which has a 3-pr ong grounding type plug and matching receptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause a ...

  • Delta DP350 - page 6

    6 DRILL PRESS P AR TS Fig. 1 Fig. 1 1 - Drill Pr ess Head and Motor 2 - Column, Base Flange, and Rack 3 - T able 4 - Base Fig. 2 5 - Chuck 6 - Clamp Handle 7 - Pinon Shaft Handles (3) 8 - T able Raising and Lowering Handle 9 - M8x1.25x125mm Carriage Head Screws (2), 8.5mm Flat W ashers (2), 8.5mm Lock Washers (2), M8x1.25 Hex Nuts (2), (for fasteni ...

  • Delta DP350 - page 7

    7 FOR YOUR OWN SAFETY , DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETEL Y ASSEMBLED AND YOU READ AND UNDERST AND THE ENTIRE INSTRUCTION MANUAL. 1. Assemble the column (A) Fig. 3, to the base (B) using the four screws, thr ee of which are shown at (C). Loosen set screw (D) and r emove ring (E) and raising rack (F). 2. M ...

  • Delta DP350 - page 8

    8 4. Slide raising rack (F) Fig. 7, table and table bracket onto drill press column, as shown. Make sur e bottom of raising rack (F) Fig. 8, is inside the flange (J) on drill press base. 5. Re-assemble ring (E) Fig. 9, which was removed in STEP 1 . IMPORT ANT : Bottom of ring (E) MUST NOT be pushed all the way down onto top of raising rack (F). MAK ...

  • Delta DP350 - page 9

    9 7. Thread stud on clamp handle (M) Fig. 12, into hole in rear of table bracket, as shown. 8. Place the drill press head (N) Fig. 13, onto the column as far as it will go. Align head (A) Fig. 13A, to table (B), and base (C). Tighten the two head locking screws (O) Fig. 13, with wr ench supplied. 9. Thread the thr ee pinion shaft handles (P) Fig. 1 ...

  • Delta DP350 - page 10

    10 10. IMPORT ANT : Make certain the spindle taper (Q) Fig. 15, and tapered hole in chuck (R) ar e clean and free of any grease, lacquer or rust pr eventive coatings. NOTE: Household oven cleaner can effectively r emove any sub- stance from the spindle and chuck; however , carefully follow the manufacturer's safety rules concerning its use. 11 ...

  • Delta DP350 - page 11

    11 Fig. 18A FLEXIBLE LAMP The flexible lamp operates independently of the drill press. T o turn the lamp “ON” and “OFF” , rotate switch (A) Fig. 18A. T o reduce the risk of fir e, use 40 watt or less, 120 volt, reflector track type light bulb (not supplied). A standard household light bulb should not be used. The reflector track type light ...

  • Delta DP350 - page 12

    12 V ARIABLE SPEED CONTROL T o avoid damaging the drive belts and pulleys, DO NOT turn speed control handles (A) Fig. 24, unless motor is running. The pilot wheel handles (A) are turned clockwise to increase speed and counterclockwise to decrease speed. The speed range is 500 rpm to 3100 rpm. Fig. 24 A A DRILLING HOLES TO DEPTH Where a number of ho ...

  • Delta DP350 - page 13

    13 ADJUSTING SPINDLE RETURN SPRING The spindle is automatically returned to its upper most position when the handle is released. It is r ecommended that the handle be allowed to slowly return to the top position after each hole has been drilled in the material. This spring has been properly adjusted at the factory and should not be disturbed unless ...

  • Delta DP350 - page 14

    14 INST ALLING AND REMOVING DRILL BITS DISCONNECT MACHINE FROM POWER SOURCE. 1. Insert smooth end of drill bit (A) Fig. 29, into chuck (B), as far as it will go, and then back the bit out 1/16", or up to the flutes for small bits. 2. Make certain that the drill bit (A) Fig. 29, is center ed in the chuck (B) before tightening the chuck with the ...

  • Delta DP350 - page 15

    15 LUBRICA TION DISCONNECT MACHINE FROM POWER SOURCE. 1. Remove the six screws (A) Fig. 30 that hold the top cover in place, and remove the top cover . 2. The variable speed pulleys should be oiled weekly with a few drops of light machine oil in the two oil holes (B) Fig. 31, located on top of the variable speed pulleys. Oil the holes when the dril ...

  • Delta DP350 - page 16

    16 Printed in U.S.A. T wo Y ear Limited W arranty Delta will repair or r eplace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized se ...

  • Delta DP350 - page 17

    The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...

Manufacturer Delta Category Drill

Documents that we receive from a manufacturer of a Delta DP350 can be divided into several groups. They are, among others:
- Delta technical drawings
- DP350 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta DP350
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta DP350.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta DP350, service manual, brief instructions and user manuals Delta DP350. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta DP350.

Similar manuals

A complete manual for the device Delta DP350, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta DP350 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta DP350.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta DP350 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta DP350, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta DP350, that we can find in the current document
3. Tips how to use the basic functions of the device Delta DP350 - which should help us in our first steps of using Delta DP350
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta DP350
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta DP350 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta DP350?

Use the form below

If you did not solve your problem by using a manual Delta DP350, ask a question using the form below. If a user had a similar problem with Delta DP350 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)