English dropdown-ico

Manual Lochinvar SSB-i & s--01

12 pages 2.58 mb
Download

Go to site of 12

Summary
  • Lochinvar SSB-i & s--01 - page 1

    Electric booster water heaters are available for operation on standard power systems. Check the nameplate for the proper power supply . All internal electrical connections have been made at the factory . See Circuit Breaker and Fuse Sizing Chart for supply wire size, fuse, breaker and conduit recommendations. AL CONNECTIONS 1. Locate the heater ter ...

  • Lochinvar SSB-i & s--01 - page 2

    PRESSURE REDUCING V AL VE Proper operation of the dishwater rinse nozzles requires available water pressure at the nozzle be between 15 and 25 psi when nozzle is operated. 20 psi is recommended. If water pressure available to the booster heater inlet is over 20 psi, a pressure reducing valve should be mounted in the hot water supply line to the boo ...

  • Lochinvar SSB-i & s--01 - page 3

    OUTLET Using a 3/4 in. union and piping connect the booster heater water outlet to the dishwasher sanitizing rinse pipe connection. Install a temperature/pressure gauge in outlet line. W ater temperature at outlet should be 180°F (82°C). The temperature sensing element must be in water stream. Manufacturer recommends a shock absorber be installed ...

  • Lochinvar SSB-i & s--01 - page 4

    CAUSE C Thermostats may not be functioning correctly or may be improperly set. SOLUTION - Inspect thermostats for proper operation and correct settings. If setting is below the maximum, reset to 190ºF(88ºC) If defective and not functioning, replace. CAUSE D Contactors are not performing. SOLUTION - Inspect contactors for proper operation by visua ...

  • Lochinvar SSB-i & s--01 - page 5

    CAUSE B Control thermostat may be set too high or be defective. SOLUTION - Reset thermostat(s). If condition is not corrected, replace thermostat(s). CHA TTERING CONT ACTOR(S) OR NOISY RELA Y . CAUSE A Contactors chatter or hum excessively when pulled in. SOLUTION - Accumulation of dirt will prevent proper seating of armature. Remove contactor and ...

  • Lochinvar SSB-i & s--01 - page 6

    6 HIGH TEMPERA TURE LIMIT SWITCH RECALIBRA TION If the temperature in the heater exceeds 210ºF (99ºC), the high temperature limit will shut off the power . The switches must be manually reset by pushing the red buttons. The limit switch has been calibrated at the factory and should not require adjusting. If the calibration changes and must be re- ...

  • Lochinvar SSB-i & s--01 - page 7

    7 CIRCUIT BREAKER AND FUSED DISCONNECT SWITCH SIZES kW VOL TS PH L1 L2 L3 Breaker or Fuse Size Copper Wire Size Conduit Size 6 208 1 29 29 — 40 8 1/2” 208 3 14 25 14 40 8 3/4” 240 1 25 25 — 40 8 1/2” 240 3 13 22 13 30 10 1/2” 480 3 6 11 6 15 14 1/2” 9 208 1 43 43 — 60 6 3/4” 208 3 22 38 22 50 8 3/4” 240 1 38 38 — 50 8 1/2” 2 ...

  • Lochinvar SSB-i & s--01 - page 8

    8 DIMENSIONS HANGING SUPPORT ...

  • Lochinvar SSB-i & s--01 - page 9

    9 PLUMBING CONNECTIONS ...

  • Lochinvar SSB-i & s--01 - page 10

    10 ...

  • Lochinvar SSB-i & s--01 - page 11

    11 ...

  • Lochinvar SSB-i & s--01 - page 12

    CP-2M-4/03-Printed in U.S.A. ...

Manufacturer Lochinvar Category Water Heater

Documents that we receive from a manufacturer of a Lochinvar SSB-i & s--01 can be divided into several groups. They are, among others:
- Lochinvar technical drawings
- SSB-i & s--01 manuals
- Lochinvar product data sheets
- information booklets
- or energy labels Lochinvar SSB-i & s--01
All of them are important, but the most important information from the point of view of use of the device are in the user manual Lochinvar SSB-i & s--01.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Lochinvar SSB-i & s--01, service manual, brief instructions and user manuals Lochinvar SSB-i & s--01. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Lochinvar SSB-i & s--01.

Similar manuals

A complete manual for the device Lochinvar SSB-i & s--01, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Lochinvar SSB-i & s--01 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Lochinvar SSB-i & s--01.

A complete Lochinvar manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Lochinvar SSB-i & s--01 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Lochinvar SSB-i & s--01, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Lochinvar SSB-i & s--01, that we can find in the current document
3. Tips how to use the basic functions of the device Lochinvar SSB-i & s--01 - which should help us in our first steps of using Lochinvar SSB-i & s--01
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Lochinvar SSB-i & s--01
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Lochinvar SSB-i & s--01 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Lochinvar SSB-i & s--01?

Use the form below

If you did not solve your problem by using a manual Lochinvar SSB-i & s--01, ask a question using the form below. If a user had a similar problem with Lochinvar SSB-i & s--01 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)