English dropdown-ico

Manual Briggs & Stratton 1694919

20 pages 1.47 mb
Download

Go to site of 20

Summary
  • Briggs & Stratton 1694919 - page 1

    A TT A CHMENT OPERA T OR’S MANU AL 42” Snow Blade Mfg. No. Description 1694919 42” Remote Angling Snow Blade 42” Sno w Blade 1732529 Revision 01 Rev. Date 02/2007 TP 100-4241-01-AT-SMA ...

  • Briggs & Stratton 1694919 - page 2

    ...

  • Briggs & Stratton 1694919 - page 3

    1 T able of Contents T roub leshooting, Adjustments & Service T roub leshooting Char t .....................................8 Skid Shoe Adjustment .....................................9 Lift Adjustment .................................................9 Initial Setup & Assembl y Install Hitch on to T ractor ...............................10 ...

  • Briggs & Stratton 1694919 - page 4

    2 Safety Rules & Information TP-600-4159-01-UV-SMAN OPERA TING SAFETY ● Always clear snow up and down the face of slopes, never across the face. Exercise extreme caution when changing direction on slopes. Do not attempt to clear steep slopes. ● Exercise extreme caution when operating on, or crossing, gravel drives, walks or roads. Stay aler ...

  • Briggs & Stratton 1694919 - page 5

    3 Features & Controls TRA CT OR CONTR OLS Before you begin operating the tractor with the dozer blade attachment, make certain you have: • Read and understood the instructions in the tractor Operator’s Manual. • Become thoroughly familiar with all of the tractor controls and their operation, including how to safely and properly start and ...

  • Briggs & Stratton 1694919 - page 6

    General Operating Instructions 4 Checks Bef ore Star ting 1. Refer to the Maintenance & Adjustments sections of this manual and perform any needed service. Also, refer to the tractor Operator’s Manual and perform any required service. 2. Remove any objects from the work area which might interfere with plowing activity. 3. Adjust the skid shoe ...

  • Briggs & Stratton 1694919 - page 7

    5 General Operating Instructions Daily Stora g e 1. Allow tractor engine to cool before storing in any enclosure. 2. After dozing or plowing jobs are completed, hose or brush down the blade to remove excess dirt. 3. Lightly oil all pivot points. Coat bare metal surfaces to prevent corrosion. IMPORT ANT NO TE Refer to Tractor Operator’s Manual for ...

  • Briggs & Stratton 1694919 - page 8

    6 Notes ...

  • Briggs & Stratton 1694919 - page 9

    7 Maintenance Schedule For Normal Care General Lubrication Lubricate the snow blade as shown in Figure 2. Where an oil can is shown use 30 weight oil. Where a grease gun is shown, use lithium grease. Lubricate the following areas: • Grease the blade pivot. • Oil the blade lock pawl • Apply grease to the plastic wear surface above the bell cra ...

  • Briggs & Stratton 1694919 - page 10

    8 T roubleshooting, Adjustments, & Service TR OUBLESHOO TING While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshoot- ing guide below lists the most common problems, their causes and r ...

  • Briggs & Stratton 1694919 - page 11

    9 T roubleshooting, Adjustments, & Service Figure 3. Skid Shoe Adjustment A – Lock Nut B – Skid Shoe Skid Shoe Adjustment On smooth surfaces such as concrete or asphalt, the scraper bar should scrape the surface. On surfaces such as gravel, the scraper bar should be set high enough so that it will not pick up debris. 1. Lower the snow blade ...

  • Briggs & Stratton 1694919 - page 12

    Ref Qty Description 1 1 Lift Assist Spring 2 7 Hair pin 3 1 Flat Washer 4 1 Lift Arm 5 1 Stand Off 6 1 Lock Washer 7 1 Bolt 8 1 Hitch Assembly 9 1 Bell Crank 10 2 Mounting Pin 11 1 Hitch Pivot Assembly 12 3 Bolt 13 2 Whiz Lock Nut Ref Qty Description 14 1 Snow Blade Assembly 15 1 Spring 16 1 Eye Bolt 17 1 Lower Control Arm 18 2 Bolt 19 2 Flange Nut ...

  • Briggs & Stratton 1694919 - page 13

    11 Initial Setup & Assembly A B Figure 6. Bell Crank Installation A. Chute Rotator Drive Cover Bolt B. Chute Rotator Drive Cover Install Hitch on to T ractor 1. Remove mower deck. 2. Install the bell crank (A, Figure 6) through the front holes (B) of the hitch assembly. NOTE: Make sure that the Lift Arm connection is to the right side of the hi ...

  • Briggs & Stratton 1694919 - page 14

    12 Initial Setup & Assembly Figure 8. Hitch Installation A. Hitch Assembly B. Hitch Support Shaft C. Hitch Mounting Arms 5. Slide hitch (A, Figure 8) under tractor and lift to slide hitch mounting arms (C) over hitch support shaft (B). 6. At front of the machine, locate and remove the lower hitch latch pin (D, Figure 9) from the hitch assembly ...

  • Briggs & Stratton 1694919 - page 15

    13 Initial Setup & Assembly Install Snow Blade Lift Arm 1. Move the mower deck lift arm to the “LOWERED” position. 2. Install the brass stand-off (A, Figure 10) at the top of the mower deck lift arm (B), using bolt (C) and wash- er (D). 3. Install the lift assist spring (E) from the rear edge of the tractor frame to the brass “C” clip ( ...

  • Briggs & Stratton 1694919 - page 16

    14 Initial Setup & Assembly Figure 11. Snow Blade Assembly A. Pivot Assembly B. Whiz Lock Nut C. Snow Blade Assembly D. Tension Spring E. Eyebolt F. Nut G. Capscrew H. Flat Washer I. Spacer A B C Figure 12. Attaching Snow Blade to Hitch A. Mounting Pin B. Hair Pin C. Bell Crank Attaching Piv ot Assembl y to Snow Blade 1. Attach the pivot assemb ...

  • Briggs & Stratton 1694919 - page 17

    15 Initial Setup & Assembly A E C G D B H F Figure 13. Blade Control Arm Installation A. Control Arm Support Bracket B. Flange Nut C. Bolt D. Eyebolt E. Upper Control Arm F. Lower Control Arm G. Nut H. Bolt E C A D B Figure 14. Lower Control Arm Installation A. Bolt B. Adjustment Arm C. Lower Control Arm D. Ball Joints E. Hair pins A B C D Figu ...

  • Briggs & Stratton 1694919 - page 18

    16 Removal Snow Blade Remo val 1. Lower the snow blade to the ground. 2. Remove the four (4) hair pins (C, Figure 16) from the control arm (A) and remove the control arm from the snow blade assembly. 3. Remove the control arm from the tractor. NOTE: The control arm support bracket can be left on the tractor. 4. Remove the bell crank hair pin (A, Fi ...

  • Briggs & Stratton 1694919 - page 19

    17 Removal 6. Remove the snow blade hair pin (B, Figure 18) and mounting pin (A). 7. Slide the snow blade assembly away from the tractor. 8. Remove the lower latch pin (A, Figure 19) from the front of the hitch assembly. 9. Lift the hitch assembly off of the support fingers (C). 10. Slide the hitch assembly (A, Figure 20) forwards until the hitch m ...

  • Briggs & Stratton 1694919 - page 20

    500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 AGCOLawn.com PRODUCTS 535 Macon Street McDonough, GA 30253 www.Snapper.com Briggs & Stratton ...

Manufacturer Briggs & Stratton Category Snow Blower

Documents that we receive from a manufacturer of a Briggs & Stratton 1694919 can be divided into several groups. They are, among others:
- Briggs & Stratton technical drawings
- 1694919 manuals
- Briggs & Stratton product data sheets
- information booklets
- or energy labels Briggs & Stratton 1694919
All of them are important, but the most important information from the point of view of use of the device are in the user manual Briggs & Stratton 1694919.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Briggs & Stratton 1694919, service manual, brief instructions and user manuals Briggs & Stratton 1694919. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Briggs & Stratton 1694919.

Similar manuals

A complete manual for the device Briggs & Stratton 1694919, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Briggs & Stratton 1694919 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Briggs & Stratton 1694919.

A complete Briggs & Stratton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Briggs & Stratton 1694919 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Briggs & Stratton 1694919, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Briggs & Stratton 1694919, that we can find in the current document
3. Tips how to use the basic functions of the device Briggs & Stratton 1694919 - which should help us in our first steps of using Briggs & Stratton 1694919
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Briggs & Stratton 1694919
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Briggs & Stratton 1694919 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Briggs & Stratton 1694919?

Use the form below

If you did not solve your problem by using a manual Briggs & Stratton 1694919, ask a question using the form below. If a user had a similar problem with Briggs & Stratton 1694919 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)