English dropdown-ico

Manual Vantec UGT-ST310R

20 pages 0.2 mb
Download

Go to site of 20

Summary
  • Vantec UGT-ST310R - page 1

    6-Port SA T A II 150 PCI Host Card w/RAID User Manual Model: UGT -ST310R All brand names and tradema rks are pr operties of the ir respective o wners. w w w . v a n t e c u s a . c o m ...

  • Vantec UGT-ST310R - page 2

    UGT -ST310R Page 2 T able of Contents 1. Bus Interface .......................................... 3 2. Connectors ............................................. 3 3. Package Contents .................................. 3 4. System Requirements ............................ 4 5. Hardware Description ............................. 4 6. Hardware Installat ...

  • Vantec UGT-ST310R - page 3

    UGT -ST310R Page 3 Features • Silicon Image SiI31 14 SA T A controller chip • Compliant with PCI S pecification, Rev . 2.3, 32-bit, 33/66Mhz • Compliant with Serial A T A 1.0 specification • Provides four independent c hannels to support up to four Serial A T A drives • Supports RAID0 (striping), RAID1 (mirroring), RAID5 (Parity RAID), RA ...

  • Vantec UGT-ST310R - page 4

    System Requirements z Pentium-class computer with one avail able PCI slot z Windows® 2000, XP/2003 32/64bit, Vista 32/64bit Hardware Description G (Jumper Settings) JP Description Act ive Po rt 1-2 close Enable SA TA Connector F J1-J4 2-3 close Enable SA TA Connector C 1-2 close Enable SA TA Connector E J5-J8 2-3 close Enable SA TA Connector D UGT ...

  • Vantec UGT-ST310R - page 5

    UGT -ST310R Page 5 Note: There are six SA T A ports in 6-Port SA T A II 150 PCI Host Card w/RAID. We name these ports from A through F . Ports A to D are internal SA T A ports. Ports E and F are external SA T A ports. Changing the jumper settings allo ws you to select between external and internal p orts to use. By default, Port A, B, C and D are w ...

  • Vantec UGT-ST310R - page 6

    UGT -ST310R Page 6 drive. 4. Attach the other end of the Serial A T A cable to the Serial A T A controller on the 6-Port SA T A II 150 PCI Host Card w/RAID. 5. Follow the same instructions to connect up to four hard drives. Device connecti on is now complete. 6. Replace the computer cover and reconn ect the power cord. RAID Arrays RAID Arrays are s ...

  • Vantec UGT-ST310R - page 7

    UGT -ST310R Page 7 3. Select RA ID0 , then press Enter . 4. Select the number of drives then press Enter . 5. Select Auto configuration , then press Enter . 6. Input the RAID size, press Enter . 7. When asked Are Y ou Sure (Y/N)? , press Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are you sure to exit (Y/N)? , press Y to exit and r ...

  • Vantec UGT-ST310R - page 8

    UGT -ST310R Page 8 RAID 1 (Mirror) For New/Blank Hard Drives 1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS. 2. At the next screen select Create R A ID Set , then press Enter . 3. At the next screen select RA ID1 then press Enter . 4. Select Auto configuration , then press Enter . 5. Input the RAID size, press Enter . ...

  • Vantec UGT-ST310R - page 9

    UGT -ST310R Page 9 9. Input the RAID size, press Enter . 10. Press Ctrl+E to exit the BIOS. 11. When asked Are you sure to exit(Y/N)? , press Y to exit and reboot. Note: If during boot the RAID BIOS reports an RAID1 set is in Rebuild st atus, The re build will contin ue af ter boot sequence is complete , disregard th e message, continue booting, an ...

  • Vantec UGT-ST310R - page 10

    UGT -ST310R Page 10 use existing hard drive(s) w ith data. T o create a RAID 0+1 set four hard drives are required. Auto configuration (recommended) The default chunk size is 64k when selecting Au t o configuration . 1. As the BIOS boots press Ctrl+S or F4 when prompted to enter the RAID BIOS. 2. At the ne xt screen select Create RAID Set , then pr ...

  • Vantec UGT-ST310R - page 11

    UGT -ST310R Page 1 1 6. Select chunk size from 8k, 16k, 32k, 64 or 128k , then pr es s Enter . 7. Select the first drive , press Enter . 8. Select the second drive , press Enter . 9. Select the third drive , press Enter . 10. Select the fourth driv e , press Enter . 11. Select Create withou t data copy then press Enter . 12. Input the RAID size, pr ...

  • Vantec UGT-ST310R - page 12

    UGT -ST310R Page 12 Enter . 3. Select RA ID5 , then press Enter . 4. Select the number of drives then press Enter . 5. Select Auto configuration , then press Enter . 6. Input the RAID size, press Enter . 7. When asked Are Y ou Sure(Y/N)? , press Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are you sure to exit(Y/N)? , press Y to exi ...

  • Vantec UGT-ST310R - page 13

    UGT -ST310R Page 13 and reboot. 15. Continue with F DISK and FORMA T steps as if you were installing a conventional hard drive. CONCA TENA TION (JBOD) This RAID array allows you to use one, t wo, three or four hard drives to a array . It does not provide any data protection or performance improvement but can b e useful for utilizing leftover space ...

  • Vantec UGT-ST310R - page 14

    UGT -ST310R Page 14 2. Select Delete RAID Set , then press Enter . 3. Select the RAID set then press Enter . 4. When asked Are Y ou Sure(Y/N)? , press Y to confirm. Resolving Conflicts When a RAID set is created, then metadata w ritten to the disk includes drive c onnection information. If, after a disk failure, the replacement disk was previou sly ...

  • Vantec UGT-ST310R - page 15

    UGT -ST310R Page 15 F BIOS Configuration The 6-Port SA T A II 150 PCI Host Card w/RAID BIOS will appear every time your system starts up. If the BIOS doesn’t show , please try your controller in another PCI slot. During this (POST ) process, the BIOS will show up and indicate the devices attached to it. Driver Installation For Windows® 2000 or A ...

  • Vantec UGT-ST310R - page 16

    UGT -ST310R Page 16 F to Windows. 2. At Found New Hardware Wizard , click Next . 3. Select Search for a su it ab le driver for my device (recommend) then click N ext . 4. Insert the driver CD, check CD-ROM drives , uncheck th e other boxes, click Next , then click Next again. 5. If the Digit al Signature Not Found message appears, click Ye s . Our ...

  • Vantec UGT-ST310R - page 17

    UGT -ST310R Page 17 For An Existing Installation 1. Setup the RAID Array prior to driver installation and boot up to Windows. 2. At the Found New Hardware Wizard, select No, not this time , then click Next . 3. Insert the driver CD, select Install the soft ware automatically (Recommend ed ) , and click Next . 4. Click Finish . 5. Restart Windows to ...

  • Vantec UGT-ST310R - page 18

    1. Setup the RAID Array prior to driver installation and bo ot up to Windows. 2. At the Found Ne w Hardware Wizard, select No, not this time, then click Next. 3. Insert the d river CD, select Inst all the soft ware automatically (Recommend ed ) , and click Next . 4. Click Finish . 5. Restart Windows to comple te the driver installation. UGT -ST310R ...

  • Vantec UGT-ST310R - page 19

    UGT -ST310R Page 19 F T o Verify Windows® Installation 1. Right click My Computer and click Manage . 3. Please insert driver CD, click Next . 4. Click Close to complete t he installation. For Windows® V ista-x64 or A New Installation A new installation requires a floppy di sk for the driver installation. T o make this floppy disk, copy the conten ...

  • Vantec UGT-ST310R - page 20

    UGT -ST310R Page 20 2. Select Device Manager . 3. Double click SCSI and RAID Controller (S torage controllers) , then double click Silicon Image SiI 31 14 SoftRA ID 5 Controller to display driver properties. A message this device is working properl y is displayed in the dialog box, the driver has been correctly installed. SA T A RAID 5 Management S ...

Manufacturer Vantec Category Computer Hardware

Documents that we receive from a manufacturer of a Vantec UGT-ST310R can be divided into several groups. They are, among others:
- Vantec technical drawings
- UGT-ST310R manuals
- Vantec product data sheets
- information booklets
- or energy labels Vantec UGT-ST310R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vantec UGT-ST310R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vantec UGT-ST310R, service manual, brief instructions and user manuals Vantec UGT-ST310R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vantec UGT-ST310R.

Similar manuals

A complete manual for the device Vantec UGT-ST310R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vantec UGT-ST310R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vantec UGT-ST310R.

A complete Vantec manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vantec UGT-ST310R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vantec UGT-ST310R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vantec UGT-ST310R, that we can find in the current document
3. Tips how to use the basic functions of the device Vantec UGT-ST310R - which should help us in our first steps of using Vantec UGT-ST310R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vantec UGT-ST310R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vantec UGT-ST310R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vantec UGT-ST310R?

Use the form below

If you did not solve your problem by using a manual Vantec UGT-ST310R, ask a question using the form below. If a user had a similar problem with Vantec UGT-ST310R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)