English dropdown-ico

Manual Acer RS700

79 pages 1.49 mb
Download

Go to site of 79

Summary
  • Acer RS700 - page 1

    AcerAltos RS700 Enclosure AcerAltos RS700 Enclosure Installation Guide Installation Guide ...

  • Acer RS700 - page 2

    ii Copyright Copyright Copyright  1998 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without th ...

  • Acer RS700 - page 3

    iii IMPORTANT SAFETY IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. ...

  • Acer RS700 - page 4

    iv 10. If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed 15 amperes. 11. Never push objects of any kind into this p ...

  • Acer RS700 - page 5

    v 16. Use only the proper type of power supply cord set (provided in your keyboard/manual accessories box) for this unit. It should be a detachable type: UL listed/CSA certified, type SVT/SJT, rated 6A 125V minimum, VDE approved or its equivalent. Maximum length is 15 feet (4.6 meters). ...

  • Acer RS700 - page 6

    vi FCC Class B Radio Frequency FCC Class B Radio Frequency Interference Statement Interference Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential ins ...

  • Acer RS700 - page 7

    vii About this Manual About this Manual Purpose This manual aims to give you all the information you need to install the enclosure. Conventions The following conventions are used in this manual: NOTE Gives bits and pieces of additional information related to the current topic. CAUTION Suggests precautionary measures to avoid potential hardware or s ...

  • Acer RS700 - page 8

    viii ...

  • Acer RS700 - page 9

    ix Table of Contents Table of Contents Chapter 1 Introduction Overview ....................................................................................... 1 Standard Configuration .................................................................. 1 Features ....................................................................................... ...

  • Acer RS700 - page 10

    x Chapter 4 Removing and Installing the Enclosure Panels Removing the Left and Right Panel ............................................ 22 Installing the Enclosure Frame ................................................... 23 Chapter 5 Cluster Server Connection Introduction ............................................................................ ...

  • Acer RS700 - page 11

    xi Install MSCS (Microsoft Cluster Server) on node2 ...................... 54 How to Confirm Acer’s Cluster Server ......................................... 57 Chapter 6 Manageability Acer RAID Manager .................................................................... 58 Advanced Server Manager (ASM) ............................................ ...

  • Acer RS700 - page 12

    ...

  • Acer RS700 - page 13

    1 Chapter 1 Introduction Overview The AcerAltos RS700 RAID Enclosure series is designed to expand more disk capacity and enhanced fault-tolerant RAID (Redundant Array of Independent Disk) with Ultra-2 SCSI performance for PC servers. This installation guide will show you how to install the basic system components such as disk drives and power suppl ...

  • Acer RS700 - page 14

    2 For RS700-TR 101: • Single SCSI Channel with 7 drive bays Default SCSI ID is 8,9,10,11,12,13, and 14 • One internal Ultra-2 SCSI terminator • One external Ultra-2 SCSI cable (1000mm) For RS700-TR 102: • Dual Internal SCSI channel: • First SCSI channel with 3 drive bays. Default SCSI ID is 0, 1, and 2 • Second SCSI channel with 4 drive ...

  • Acer RS700 - page 15

    3 For RS700-RM 101: • Single SCSI Channel with 7 drive bays Default SCSI ID is 8,9,10,11,12,13, and 14 • One internal Ultra2 SCSI terminator • One external Ultra2 SCSI cable (2500mm) For RS700-RM 102: • Dual Internal SCSI channel: • First SCSI channel with 3 drive bays. Default SCSI ID is 0, 1, and 2 • Second SCSI channel with 4 drive b ...

  • Acer RS700 - page 16

    4 • Power Supply • Supports up to two 300 W power supplies • Redundant and hot-swappable for on line maintenance • Manageability (for RM102/TR102 models only) • Components can be monitored with management utility (hard disk drive, power supply, hard disk drive cooling fan and housing fan) • Power and hard drive failure LED • Easy-to-u ...

  • Acer RS700 - page 17

    5 Front Panel The Power LED blinks if the power supply fails. The ID number LED displays a “]” sign when the fan of the SCSI hard disk drive tray fails. Power Switch Power LED SCSI RAID Controller (for TR102/RM102 models only) Hot-swap Removable Drive Bays ID Number LED ...

  • Acer RS700 - page 18

    6 Rear Panel Getting Started Before you turn on the storage enclosure do the following: 1. Make sure the power voltage switch (115 volts or 230 volts) is set correctly to the right voltage before turning on the power. 2. Install the RS700 into the Rack (for RM101 and RM102 models only). 3. Install the SCA hard disk drives into the drive trays and c ...

  • Acer RS700 - page 19

    7 5. Connect the external Ultra-2 SCSI cable between the host server and RS700. 6. Power on the RS700. 7. Configure the Acer RAID controller on the RS700 (for TR/102 and RM102 models only). Refer to the AcerAltos 3102RS and Acer RAID Manager User’s Guides for more information. 8. Unlock the drive trays if they do not have a hard disk drive inside ...

  • Acer RS700 - page 20

    8 Chapter 2 Hardware Installation Drive Tray and Back Plane Board Before touching any electrical equipment, ground yourself by touching the metal part of your computer chassis. This discharges any static electricity and will prevent any damage to your computer. Drive Tray The LED display determines the status of the drive tray and the hard disk dri ...

  • Acer RS700 - page 21

    9 To install a hard disk drive: 1. Unlock a drive tray and pull it out. 2. Use both hands to push out the top cover of the drive tray as shown below and then the bottom cover to expose the drive tray frame. 3. Insert the hard disk drive into the SCSI connector board frame. ...

  • Acer RS700 - page 22

    10 Make sure that the hard disk drive is properly inserted. 4. Secure the hard disk drive with four screws. 5. Replace the top and bottom cover by placing the cover to one side of the frame and then pushing down the other side to close it as shown below. ...

  • Acer RS700 - page 23

    11 6. Set the ID number for the drive using the turn key. The ID number dial is located at the rear of the disk tray. Make sure that you do not use duplicate ID numbers. 7. Insert the tray back into the enclosure and lock it (which also powers up the drive tray). The ID number LED should indicate the ID number you set for this hard disk drive, and ...

  • Acer RS700 - page 24

    12 Removing and Installing the Redundant Power Supply Follow the instructions in this section when you want to install or remove the redundant power supply modules. To reduce the risk of electric shock, make sure to disconnect all power supply cables from the wall socket before opening the system enclosure. The power supplies have a power indicator ...

  • Acer RS700 - page 25

    13 To stop the alarm, simple press the red button located at the rear of the enclosure. However, the Power LED will continue blinking until the power supply is working properly. Removing a Redundant Power Supply 1. Unlock the power supply. This action also turns off the power supply. 2. Lift the handle and carefully pull the power supply until it d ...

  • Acer RS700 - page 26

    14 ...

  • Acer RS700 - page 27

    15 Installing the RS700-RM101/102 into the AcerAltos Rack The RS700-RM101/102 model is specifically designed for the AcerAltos Rack. This model also includes two angular steel bars for installation purposes. Vertical Mounting Hole Pattern The four vertical rails of the AcerAltos Rack contain mounting holes arranged in a manner shown in this figure: ...

  • Acer RS700 - page 28

    16 The distance from the center of two holes with closer spacing to the center of the next pair is equivalent to 1U. When installing components, you must start your measurement from the center of the two holes with closer spacing. Otherwise, the screw holes on the component may not match with those on the rack. To install the RS700-RM101/102 into t ...

  • Acer RS700 - page 29

    17 3. Slide in the RS700 enclosure into the AcerAltos Rack and secure it with four screws as shown below. When you slide in the enclosure make sure that the lower part of the support bar is resting on the angular bar. Support Bar ...

  • Acer RS700 - page 30

    18 Chapter 3 Setting Up the RS700 The setups defined here are samples to show you how to take advantage of the features of the RS700 to extend and expand its functions. For RS700-TR101/RM101 Models LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD Cable LVD cable LVD Terminator HBA Expander LVD-to-SE On-board /add-on SCSI 7880 External SC ...

  • Acer RS700 - page 31

    19 For RS700-TR102/RM102 Models LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD HBA Expander LVD-to-SE On-board /add-on SCSI 7880 Using two SCSI Expander to extend the cable length of the enclosure. LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD LVD HDD HBA Using the SCSI Expander to connect directly to an add-on card LVD SCSI controller. ...

  • Acer RS700 - page 32

    20 For more information about the SCSI Expander, please refer to Appendix B. Connecting Two RS700s into a SCSI Channel (for TR102/RM102 only) To connect two RS700s into one host server: 1. Remove a screw to open the top panel of the enclosure . 2. Disable the terminator of the SCSI expander in the first RS700. The terminator of the SCSI expander in ...

  • Acer RS700 - page 33

    First RS700 Storage Enclosure Second RS700 Storage Enclosure Host Server HBA ...

  • Acer RS700 - page 34

    22 Chapter 4 Removing and Installing the Enclosure Panels Before touching any electrical equipment, ground yourself by touching the metal part of your computer chassis. This discharges any static electricity and will prevent any damage to your computer. Removing the Left and Right Panels 1. Turn off power to the system unit and unplug all cables. 2 ...

  • Acer RS700 - page 35

    23 Installing the Enclosure Frame 1. After removing the left and right panels, remove the screws located on the four corners of the enclosure. 2. Gently pull out the entire frame to access the inside components. To reattached the enclosure frame, simply reverse the procedures discussed above. ...

  • Acer RS700 - page 36

    24 Chapter 5 Cluster Server Connection Introduction A cluster is a group of independent network servers that present themselves to a network as a single system. Often MIS administrator only manage a cluster as a single system. MSCS (Microsoft Cluster Server) clustering provides three main benefits: 1. High availability of resources. Single device f ...

  • Acer RS700 - page 37

    25 3. Centralized administration. The administration of applications and services is centralized through the use of CLUSTER ADMINISTRATOR. Cluster solution for AcerAltos Server You can use the two AcerAltos servers, one hub and the cluster cable kits of Acer’s cluster to build up the cluster environment, and then setup the MSCS by using the Micro ...

  • Acer RS700 - page 38

    26 Acer’s Cluster Solution Solutions 1. Two-node Cluster that comply with MSCS (Microsoft Cluster Server). 2. Two AcerAltos Servers + AcerAltos RS700 RAID Storage. 3. AcerAltos 3102RS RAID Box supporting three Ultra SCSI Channels: One for host channel, and two for drive channels. 4. SCSI Expander (Optional) a) Convert Single-ended into LVD. b) Bu ...

  • Acer RS700 - page 39

    27 SCSI Expander ...

  • Acer RS700 - page 40

    28 The Architecture of Acer’s Cluster Server Hub Public Network Private Network AcerAltos Server BPB External LVD Cable AcerAltos RS700 3102RS RAID Box BPB CH1 CH2 CH0 68-pin Ultra SCSI SCSI Expander Card Ultra2 SCSI Card ...

  • Acer RS700 - page 41

    29 Two-node Cluster Cable Kits for Rackmount or Stand- Alone Cluster Cable kit for RackMount Includes the following items: 1. External Ultra2 SCSI Cable (2500mm) * 1 2. STP Cross-Over Cable * 1 (for private network) Cluster Cable kit for Stand-Alone It includes the following items: 1. External Ultra2 SCSI Cable (1000mm) * 1 2. STP Cross-Over Cable ...

  • Acer RS700 - page 42

    30 System Requirements Hardware Requirements: • AcerAltos Server * 2 (w/I two SCSI channels and two NICs) • AcerAltos RS700 RAID Storage * 1 • One Network Hub + LAN Cables • Two-node Cluster Cable Kit Software Requirements: • Microsoft Windows NT server 4.0, Enterprise Edition • Other Applications (Optional) (i.e., SQL Server, Exchange ...

  • Acer RS700 - page 43

    31 Hardware Installation and Configuration Hardware Installation 1. Ensure that you have got the all of the hardware requirements of Acer’s cluster server, and refer to the architecture of Acer’s Cluster to build up the cluster. 2. Connect the private network between two nodes by using the STP cross- over cable. 3. You must insert another NIC o ...

  • Acer RS700 - page 44

    32 2. Configuring the RAID Box. It is very important to configure the RAID Box to create Acer’s cluster server. a) Assume we insert three 4GB hard disks on the AcerAltos RS700, and their ID is 0, 1, and 2. b) Planning the SCSI Channels of the RAID Box. Assign channel 0 to the Host channel. Assign channel 1 to the Device channel Assign channel 2 t ...

  • Acer RS700 - page 45

    33 b) The following are guidelines on using the serial port: • The serial port’s default is set at 9,600 baud, 8 bits, 1 stop bit and no parity. • In most cases, connecting RD, TD and SG are enough to establish communication with a terminal. • If you are using a PC as a terminal, any VT-100 terminal emulation software will suffice. Microsof ...

  • Acer RS700 - page 46

    34 Since the controller is totally operating system independent, the operating system of the host computer will not be able to find out whether the attached devices are physical hard drives or virtual system drives created by the RAID controller. A ‘Logical Drive" is a set of drives grouped together to operate under a given RAID level and ap ...

  • Acer RS700 - page 47

    35 7. Create four partitions in LG 0. Microsoft Cluster needs two or more physical drivers, so you can choose "LG 0" and "Partition logical drive" to create four partitions in one logical driver. For example: Partition Offset(MB) Size(MB) 0 0 2000 1 2000 2000 2 4000 2000 3 6000 2000 8. Map Host LUN: a) Choose "View and edit ...

  • Acer RS700 - page 48

    36 Planning your Cluster Environment Windows NT Configuration 1. Cluster servers must be in the same domain. 2. Install the cluster as domain administrator. 3. Cluster servers may assume the following models in an NT domain: a) PDC-BDC b) BDC-BDC c) Member servers 4. Cluster servers belong to only one cluster. 5. They do not support FAT and only su ...

  • Acer RS700 - page 49

    37 3. One static TCP/IP address of the cluster and one for each resource group that will be created. 4. All nodes must be the same subnet. ...

  • Acer RS700 - page 50

    38 Software Installation and Configuration Set up the cluster server software by taking the following steps: 1. Power on the External Shared Storage. Don’t power off the External Shared Storage while setting up the Cluster. 2. Install Windows NT server 4.0 on node1. 3. Install Windows NT server 4.0 on node2. 4. Check the functions of the network ...

  • Acer RS700 - page 51

    39 Install Windows NT server 4.0 on node1 1. Put at least one HDD on node 1. 2. Power on node1 and begin to install Windows NT server 4.0 by using the software "MS Windows NT server 4.0, Enterprise Edition" (Don’t power on node 2). 3. Format the system drive to NTFS. 4. Create the cluster domain, and then configure this node as PDC (Pri ...

  • Acer RS700 - page 52

    40 Install Windows NT server 4.0 on node2 1. Put at least one HDD on node 2. 2. Don’t power off node 1. 3. Power on node2 and begin to install Windows NT server 4.0 by using the software "MS Windows NT server 4.0, Enterprise Edition". 4. Format the system drive to NTFS. 5. Join the cluster domain of node 1, and then configure this node ...

  • Acer RS700 - page 53

    41 Check the Network Functions Between the Two Nodes 1. Ensure that node 1 can ping the IP address and computer name of node 2. For example, A:> Ping 192.0.0.2 A:> Ping 192.10.10.2 A:> Ping node2 2. Ensure that node 2 can ping the IP address and computer name of node 1. For example, A:> Ping 192.0.0.1 A:> Ping 192.10.10.1 A:> Ping ...

  • Acer RS700 - page 54

    42 Format the Shared Drives on the AcerAltos RS700 After finishing the installation of node 1 and node 2, begin to format the shared drives on the AcerAltos RS700. 1. Power on the node 1 and Power off node 2. 2. Assume that there is one HDD and one CD-ROM on node 1. 3. Configure the system drive as drive C: and CD-ROM as drive D:. You will find the ...

  • Acer RS700 - page 55

    43 7. Configure the system drive as drive C: and CD-ROM as drive D:. 8. You will find the other four formatted drives on the Disk Administrator. 9. Assign the sticky drive letters which are the same as the driver letters of node 1 to all shared drives. For example: Assign I, J, K, and L to these four drivers of node 2. ...

  • Acer RS700 - page 56

    44 Install MSCS (Microsoft Cluster Server) on Node1 1. Power off node 2. 2. Put CD 1 of " Windows NT Server 4.0, Enterprise Edition" in the CD- ROM, and run the d:sp3Spsetup.bat to install Service Pack 3. 3. Begin to Install Service Pack 3: You must install Service Pack 3 to complete the installation of Windows NT Enterprise Edition. ...

  • Acer RS700 - page 57

    45 4. Put CD 1 of " Windows NT Server 4.0, Enterprise Edition" in the CD- ROM, and run the d:i386Nhloader.exe to install MSCS. 5. Begin to install MSCS. ...

  • Acer RS700 - page 58

    46 6. Select the "Microsoft Cluster Server" to install. 7. Insert CD 2 of “ Windows NT Server, Enterprise Edition". ...

  • Acer RS700 - page 59

    47 8. Select "Form a new cluster" to create a cluster. 9. Input the name of the Cluster. ...

  • Acer RS700 - page 60

    48 10. Input the path for cluster files. 11. Input the User name and Password of this Domain account. ...

  • Acer RS700 - page 61

    49 12. Add or Remove the shared disks. 13. Select the shared disk on which to store permanent cluster files. ...

  • Acer RS700 - page 62

    50 14. Input the network name associated with the Adapter Name "EI59x1". 15. Input the network name associated with the Adapter Name "E100B2". ...

  • Acer RS700 - page 63

    51 16. Select the node1-pri and click "UP" to get the highest priority. ...

  • Acer RS700 - page 64

    52 17. Enter the IP Address and Subnet Mask of the Cluster. 18. MSCS has been successfully installed. ...

  • Acer RS700 - page 65

    53 19. Reboot node 1. 20. Open the connection to the cluster: a) Select the "Administrator tools" and then open the "Cluster Administrator". b) Input the Name of this Cluster. c) Confirm the successful installation of node1. ...

  • Acer RS700 - page 66

    54 Install MSCS (Microsoft Cluster Server) on node2 1. Don’t power off node 1. 2. Stop the cluster service of node 1 from Services of the Control Panel. 3. Power on node 2. 4. Begin to Install Service Pack 3. 5. Restart the cluster service of node 1 from Services on the Control Panel. 6. Put CD 1 of " Windows NT Server 4.0, Enterprise Editio ...

  • Acer RS700 - page 67

    55 10. Select "Join an existing cluster" to create a cluster. 11. Input the name of the Cluster. 12. Input the path for cluster files. 13. Input the Password of this Domain Account. 14. MSCS has been successfully installed. 15. Reboot node 2. 16. Open the connection to the cluster: a) Select the "Administrative tools" and then o ...

  • Acer RS700 - page 68

    56 ...

  • Acer RS700 - page 69

    57 How to Confirm Acer’s Cluster Server 1. Open the Cluster Administrator to connect both nodes in the cluster. 2. Attempt to start and stop the cluster service from the control panel. 3. Attempt to take resources off-line and bring them online. ...

  • Acer RS700 - page 70

    58 Chapter 6 Manageabilit y Acer RAID Manager • Allows you to control and monitor RS700 RAID Storage, either from a local host, or from a remote station connected through a LAN, telephone line, or the Internet. • GUI running under Windows NT/Win 95/Win 98. • Supports remote management over the network of host/agents running Windows NT or Wind ...

  • Acer RS700 - page 71

    59 Appendix A AcerAltos 3102RS RAID (Redundant Array of Independent Disks) Controller The AcerAltos 3102RS RAID controller is an Ultra- Wide-SCSI-to-Ultra-Wide- SCSI RAID controller specifically designed to provide RAID 0, 1, 3, or 5 capability to any host system equipped with a SCSI interface. It is totally independent of the host system’s opera ...

  • Acer RS700 - page 72

    60 • Comprehensive failure management including: • Automatic bad sector reassignment • Hot-swapping • Spare drive operation (supports both global spare and local spare) • Background rebuilding (rebuild priority selectable) • Verify-after-write supported on normal writes, rebuild writes and/or RAID initialization writes • Works with an ...

  • Acer RS700 - page 73

    61 • Supports Fault-bus for enclosure management Channel Connection Setup Table Channel # Host/Drive Channel ID# Terminator Connection CH0 Host 0 On Connect to the SCSI expansion slots and ready to connection with the host server CH1 Drive 7 On Connect to the first 3 drive trays CH2 Drive 7 On Connect to the last 4 drive trays ...

  • Acer RS700 - page 74

    62 Appendix B SCS I Expander SCSI Expander (EP-SL) Single-ended and Low Voltage Differential signals are incompatible at the electrical level: however, you can use a converter to change the signals. The SCSI Expander is an extension and a converter card for SCSI devices. It converts Single-Ended (SE) electrical signal type to Low Voltage Differenti ...

  • Acer RS700 - page 75

    63 Layout * Black shading indicates pin 1 Connector/ Jumper Description CN1 Internal 68-pin W ide SCSI connector (LVD) CN2 External 68-pin W ide SCSI connector (LVD) CN3 Internal 68-pin W ide SCSI connector (SE) JP1 Power connector JP2 SCSI Terminator 1-2 On (Default) 2-3 Off ...

  • Acer RS700 - page 76

    64 SCSI Terminator Jumper When set to On, you can only use either one of the connectors (CN1 or CN2). If set to off, both the internal (CN1) and external (CN2) 68-pin Wide SCSI connectors (LVD) can be used. Installing the SCSI Expander Always observe the following electrostatic discharge (ESD) precautions before installing a system component: • D ...

  • Acer RS700 - page 77

    65 Connecting the SCSI Expander The SCSI Expander card not only converts SE electrical signals but also extends its limited cable length by converting SE to LVD. Interconnection Table Items Fast Wide SCSI Wide Ultra SCSI Wide Ultra2 SCSI Transfer Rate (MB/s) 20 40 80 Max. Cable Length : Number of drives SE 6M : 8D SE 1.5M : 8D 3M : 4D 12M : 16D As ...

  • Acer RS700 - page 78

    66 The expander converts the signal to LVD allowing it to extend the range of the signal. Here are a few example of how to use the expander to extend and expand signal length. Using two SCSI Expanders to extend the signal length of a Ultra-wide SCSI controller to the storage housing. Using a SCSI Expander to connect directly to the Ultra-2 SCSI con ...

  • Acer RS700 - page 79

    67 Appendix C Troubleshooting What’s that alarm sound? The alarm sound is a warning that means that there is something wrong with the enclosure. It might be one of two things: the power supply or the housing fan failed. To disable the alarm, push the red button located at the back of the housing. See chapter 1 for the location of the red button. ...

Manufacturer Acer Category Altos Server

Documents that we receive from a manufacturer of a Acer RS700 can be divided into several groups. They are, among others:
- Acer technical drawings
- RS700 manuals
- Acer product data sheets
- information booklets
- or energy labels Acer RS700
All of them are important, but the most important information from the point of view of use of the device are in the user manual Acer RS700.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Acer RS700, service manual, brief instructions and user manuals Acer RS700. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Acer RS700.

Similar manuals

A complete manual for the device Acer RS700, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Acer RS700 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Acer RS700.

A complete Acer manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Acer RS700 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Acer RS700, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Acer RS700, that we can find in the current document
3. Tips how to use the basic functions of the device Acer RS700 - which should help us in our first steps of using Acer RS700
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Acer RS700
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Acer RS700 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Acer RS700?

Use the form below

If you did not solve your problem by using a manual Acer RS700, ask a question using the form below. If a user had a similar problem with Acer RS700 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)