Manual Transition Networks SSDTF1025-105

9 pages 0.7 mb
Download

Go to site of 9

Summary
  • Transition Networks SSDTF1025-105 - page 1

    Installation . . . . . . . . . . . . . . . . . . . . .3 Operation . . . . . . . . . . . . . . . . . . . . . .9 Cable Specifications . . . . . . . . . . . . .10 Technical Specifications . . . . . . . . . .12 Troubleshooting . . . . . . . . . . . . . . . .13 Compliance Information . . . . . . . . .16 * Typical maximum cable distance. (Actual distance ...

  • Transition Networks SSDTF1025-105 - page 2

    2 SSDTF10xx-10x (TX) = transmit (RX) = receive * Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. ** SSDTF1029-105 and -106 are intended to be installed in the same network where one is the local device and the other is the remote device. *** SSDTF1029-107 and -108 are intended to be ins ...

  • Transition Networks SSDTF1025-105 - page 3

    4 SSDTF10xx-10x Installation -- Continued Set the loop-back switch Hardware mode: The loop-back switch is located on the front panel of the device and is used for installation and network debugging procedures. To set the switch, use a small flat-blade screwdriver or a similar device (see the drawing to the right). CL (Copper loop-back) Enable loop- ...

  • Transition Networks SSDTF1025-105 - page 4

    6 SSDTF10xx-10x Installation -- Continued Settings for T1 configuration (right switch set, SW 1) T1/long-haul signal Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the drawing below). Use switches 1 and 2 on the right switch set to select the proper network cable settings. The drawing below lists the four options. -1 ...

  • Transition Networks SSDTF1025-105 - page 5

    8 SSDTF10xx-10x Installation -- Continued Install the copper cable 1. Locate or build twisted-pair copper cables that are compliant with the specifications on page 11 with RJ-45 connectors at both ends. 2. Ensure that the MDI/MDI-X switch is set according to the network conditions (see page 3) . 3. Connect the RJ-45 connector at one end of cable to ...

  • Transition Networks SSDTF1025-105 - page 6

    10 SSDTF10xx-10x Cable Specif ications Fiber cable Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm SSDTF1011-105 850 nm multimode Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm Link ...

  • Transition Networks SSDTF1025-105 - page 7

    12 SSDTF10xx-10x T echnical Specifications For use with Transition Networks Model SSDTF10xx-10x or equivalent Standards: Emissions: CISPR A; Telecordia TR-NWT-001089 (designed to meet; NOT tested) ; FCC Part 68; T1/E1 Physical layer: ITU-T, ANSI, AT&T, and ETSI; European Technical Standard: TBR 12; British Technical Publication: PD 7024 : 1994 ...

  • Transition Networks SSDTF1025-105 - page 8

    14 SSDTF10xx-10x 4. Is data transfer failing? YES • Verify the local copper connection by starting a local copper loop-back (hardware mode: set the loop-back switch on the local device to “CL”, software mode: enter the local copper loop-back command) and then use a bit error test unit to run a bit error test. • Verify the local fiber connec ...

  • Transition Networks SSDTF1025-105 - page 9

    Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial ...

Manufacturer Transition Networks Category Network Card

Documents that we receive from a manufacturer of a Transition Networks SSDTF1025-105 can be divided into several groups. They are, among others:
- Transition Networks technical drawings
- SSDTF1025-105 manuals
- Transition Networks product data sheets
- information booklets
- or energy labels Transition Networks SSDTF1025-105
All of them are important, but the most important information from the point of view of use of the device are in the user manual Transition Networks SSDTF1025-105.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Transition Networks SSDTF1025-105, service manual, brief instructions and user manuals Transition Networks SSDTF1025-105. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Transition Networks SSDTF1025-105.

A complete manual for the device Transition Networks SSDTF1025-105, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Transition Networks SSDTF1025-105 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Transition Networks SSDTF1025-105.

A complete Transition Networks manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Transition Networks SSDTF1025-105 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Transition Networks SSDTF1025-105, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Transition Networks SSDTF1025-105, that we can find in the current document
3. Tips how to use the basic functions of the device Transition Networks SSDTF1025-105 - which should help us in our first steps of using Transition Networks SSDTF1025-105
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Transition Networks SSDTF1025-105
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Transition Networks SSDTF1025-105 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Transition Networks SSDTF1025-105?

Use the form below

If you did not solve your problem by using a manual Transition Networks SSDTF1025-105, ask a question using the form below. If a user had a similar problem with Transition Networks SSDTF1025-105 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Comments (0)