English dropdown-ico

Manual JAI M4+ CL

31 pages 1.76 mb
Download

Go to site of 31

Summary
  • JAI M4+ CL - page 1

    Digital Monochrome and Color Megapixel Progressive Scan Cameras CV -M4 + /M4 + CL CV -M7 + /M7 + CL Operation Manual Camera: Revision B Manual: Version 1.0 Preliminary M4plusBman1may07.doc JPT 07 -05-03 ...

  • JAI M4+ CL - page 2

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 1 - T able of contents 1. General ........................................................................................................ 2 2. Standard Co mposition ...................................................................................... 2 3. Main Features ......................................... ...

  • JAI M4+ CL - page 3

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL 1. Gener al This manual will cover the following 4 cameras: CV-M4 + /CV-M4 + CL and CV-M7 + /CV-M7 + CL. The revision B cameras are updated with a new function, Restart Continuous Trigger mode (RCT). The trigger can be H a-synchronous or H synchronous. Binning is now only vertical. The cameras are based on pr ogre ...

  • JAI M4+ CL - page 4

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 3 - 4. Locations and F unctions 1. CCD sensor 2. Lens mount (C-mount) 3. Rear panel with SW1 4. Digital output connector 5. DC in/Trigger in/RS-232C con nector 6. Gain potentiometer 7. Mounting holes M3 Fig. 1. Locations ...

  • JAI M4+ CL - page 5

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 4 - 5. Pin Assignment 5.1. 12-pin Multi-conne ctor (DC-IN/RS232C) Type: HR10A-10R-12PB-01 (Hirose) male. (Seen from rear of camera.) 3 4 5 6 7 8 9 10 11 12 1 2 *) Iris video out w ithout sync. Refer to 5 .4.1 video output *1) EEN or c. sync out select by RS232C command SE Fig. 2. 12-pin connector. *2) input on 1 ...

  • JAI M4+ CL - page 6

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 5 - 5.3. Digital Output Connector for Camera Link This pin configuration is only valid for CV-M4 + CL and CV-M + 7CL Pin no. Signal Function Remarks 1 14 Shield Shield 2 15 -/+ TX0 2 16 -/+ TX1 4 17 -/+ TX2 Video signal, LEN, FEN, DVAL and EEN Multiplexed signals 5 18 -/+ TXCLK Pixel clock 6 19 -/+ TX3 Video, LE ...

  • JAI M4+ CL - page 7

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL 5.4. Input and Output Circuits GND #4/12 75 Video Output NC 68p 1 µ 2 L 500 mV GND Black level GND #4/12 75 Video Output NC 68p 1 µ 2 L 500 mV GND Black level 5.4.1. Video output The analogue video output without composite sync is a 75 Ω DC co upled circuit. It is for test only. It can be used for iris co ntro ...

  • JAI M4+ CL - page 8

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 7 - 5.4.5. Camera Link interface For Camera Link the digital output signals foll ow the Camera Link standardized multi plexed signal output interface. The output driver is NS type DS90CR283, and the receiver is NS type DS90CR284. The data bits from the 10 bit digital video, FE N, LEN. EEN and DVAL are multiplexe ...

  • JAI M4+ CL - page 9

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 8 - 5.5. CV-M4 + Block Diagram Fig. 9. Block diag ram for the camera 6. F unctions and Oper ations 6.1. Basic functions The CCD scanning format can be selected between full or partial scanning. With partial scanning only the vertical central part of the CCD sen sor is read out with a higher frame rate. The parti ...

  • JAI M4+ CL - page 10

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 9 - Binning mode is a func tion where the signal charge from 2 or more adjacent pixels are ad ded together and read out as one pixel. A resulting f ull frame with lower spatial resolution can be read out with a higher rate, and higher sensitivity. The CV-M4 + has vertical binning where the pixel charge from 2 ad ...

  • JAI M4+ CL - page 11

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 10 - Color versions CV-M7 + and CV-M7 + CL These color cameras are identical to the monochrome cameras. Only the CCD sensor is changed to a RGB primary color type. Here t he color mosaic lay out is shown in fig. 13. left. This lay out is known as a Bayer f ilter. Based on the knowle dge to this mosaic, a full RG ...

  • JAI M4+ CL - page 12

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 11 - Restart Continuous Trigger mode. RCT . The RCT mode makes it possible to use a lens wi th video controlled iris for intelligent traffic surveillance applications, ITS. The camera is running continuously, and the iris is controlled from the iris video output. When a trigge r pulse is applied , the scanning i ...

  • JAI M4+ CL - page 13

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL 6.3. Continuous Operation (Non triggered) Mode settings can be done with either RS-232 C or switches. Trigger Mo de Normal. TR=0. It is for applications where the camera is continuous runni ng without external trigger. The shutter mode can be normal or programmable exposure. (SM= 0, SM=1). The shutter will work in ...

  • JAI M4+ CL - page 14

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 13 - Fig. 17. Vertical timing details, full frame. Fig. 17A. Vertical timing details with vertical binning (M4 + and M4 + CL only). ...

  • JAI M4+ CL - page 15

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 14 - Fig. 18. Vertical timing details with 1/2 partial scanning. Fig. 18A. Vertical timing details with 1/4 partial scanning. Fig. 18B. Vertical timing details with 1/8 partial scanning. Table showing timing figures for continuous modes Scanning mode Lines/ frame Lines in video out Pixels/ line Pixels/line in vi ...

  • JAI M4+ CL - page 16

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 15 - 6.4. External Trigger Modes This camera has 3 external asynchr onous trigger modes, which can be s et by RS-232C commands or switches. 1. Edge Pre-select Mod e. TR=1 Pre-selected exposure. (SM=0, SM=1) 2. Pulse Width Control Mode. TR=2 Pulse width controlled exposure. 3. Fram e Delay read out mode. TR=3 Pre ...

  • JAI M4+ CL - page 17

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 16 - 6.5. Edge Pre-select Mode The trigger leading edge will st art the exposure H synchronous or H a-synchronous (HC=0, H C=1). The exposure stops and is read out after the shutter time selected. It can be the 10 steps in normal or 1056 steps in programmable. SM=0 or SM=1. This mode will operate with full and p ...

  • JAI M4+ CL - page 18

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 17 - Remark that the dump read out in smearless takes 133H before the acc umulation start. Fig. 20A. Edge Pre-select, smearless Fig. 21. Edge Pre-select with Restar t Continous Trigger. ...

  • JAI M4+ CL - page 19

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 18 - 6.6. Pulse Width Control Mode In this mode the exposure starts from the leadin g edge of the trigger pulse, H sync hronous or H a-synchronous. It stops at the trailing edge of the trigger pulse, and th e resulting video is read out. This mode will operate with fu ll and partial scanning and with all binning ...

  • JAI M4+ CL - page 20

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 19 - 6.7. Frame-delay read out Mode In this mode the pre selected exposure starts from the leading edge of the trigger pulse, H synchronous or H a-synchronous. It can be the 10 steps in normal or 1056 steps in programmable. SM=0 or SM=1. The result ing video is read out at the trailing edge of the trigger. This ...

  • JAI M4+ CL - page 21

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 20 - 6.8. Frame-delay read out Mode with multiple exposure. Multiple exposures is possible in frame delay re ad out mode. The pre selected exposure starts from the leading edge of the trigger pulse. It can be the 10 steps in normal or 1056 steps in programmable. SM=0 or SM=1. The resulting video is re ad out at ...

  • JAI M4+ CL - page 22

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 21 - 6.9. Other Functions. Functions which can be controlled by either RS-232C or swit ches, or both. Gain and set-up. !! Do not adjust these s ettings unless you have knowl edge to video adjustments !! The video gain is set to man ual . In manual g ain mode, either the gain level (GA) or the rear potentiometer ...

  • JAI M4+ CL - page 23

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 22 - 7. Configuring the Camer a 7.1. Mode setting SW1 on rear second s OFF ON 1 2 3 4 5 6 7 8 CONTROL SHUTTER SCANNI NG < < > > < > < > < > Nor mal < > Local R S232C Sm ea r- less < < < < < < < < > < < > < > < < > < < &g ...

  • JAI M4+ CL - page 24

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 23 - 7.4. RS-232C control All configuration of the CV-M4 + camera is done via the RS-232C port. On the 12 pin Hirose connector, if JP301 is open, or via Camera Link if JP30 1 is short. The camera can be set up from a PC running terminal emulator s oftware, or using JAI´s camera contr ol software. Below is the d ...

  • JAI M4+ CL - page 25

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 24 - 7.5. CV-M4 + command list Command Name Form at Parameter Remarks A – General settings and useful co mmands EB Echo Back EB= [ Param. ] <CR><LF> 0=Echo off 1=E cho on Off at power up ST Camera Status request ST?<CR><LF> Actual setting HP Online Help reques t HP?<CR><LF> ...

  • JAI M4+ CL - page 26

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 25 - 7.6. Camera Control Tool for CV-M4 + From www.jai.com Camera Control Tool for Windows 98/NT/2000 can be downloaded. The control tool contents a camera control program and tools for m aking your own program. Below the different windows are sh own. Fig. 28. Camera contro l tool windows. For the integrator and ...

  • JAI M4+ CL - page 27

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 26 - 8. External Appearance and Dimensions Fig. 29. Outline 9. Specifications 9.1. Spectral sensitivity Wa v e l en g t h (n m ) 400 5 00 600 7 00 8 00 1. 0 0. 8 0. 6 0. 4 0. 2 0. 0 R el at i ve resp onse IR s t op B G R Wa v e l en g t h (n m ) 400 5 00 600 7 00 8 00 1. 0 0. 8 0. 6 0. 4 0. 2 0. 0 R el at i ve r ...

  • JAI M4+ CL - page 28

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL 9.2. Specification table Specifications CV-M4+/CV-M4 + CL CV-M7+/CV-M7 + CL Scanning system Progressive 1060 lines 24 frames/ sec. Pixel clock 40.49 MHz 40.49 MHz Line frequency Line freq. with V binnig 25.43 kHz (1592 pixel clock/line) 25.11 kHz (1752 pixel clock/line) 25.43 kHz (1592 pixel clock/line) - Frame ra ...

  • JAI M4+ CL - page 29

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 28 - 10. Appendix 10.1. Precautions Personnel not trained in dealing with similar elec tronic devices should not service this camera. The camera contains components sensitive to el ectrostatic discharge. The handling of these devices should follow the requirements of electrostatic se nsitive components. Do not a ...

  • JAI M4+ CL - page 30

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 29 - 10.3. Camera Link Test points Inside the camera Link versions c ameras CV-M 4+CL and CV-M7+CL there are some useful test points, which can be a b ig help in system troubleshooting. The timing signals are multiplexed into the Came ra Link, so it is not possible to use an oscilloscope to control the timing fo ...

  • JAI M4+ CL - page 31

    CV-M4 + /M4 + CL, CV-M7 + /M7 + CL - 30 - 11. Users Record Camera type: CV-M4 + M4 + CL M7 + M7 + CL Revision: (Revision B) Serial No. …………….. Software version. …………….. For camera revision hi story, please contact your local JAI d istributor. Users Mode Settings. Users Modifications. DECLARA TION OF CONFORMITY AS DEFINED BY THE ...

Manufacturer JAI Category Security Camera

Documents that we receive from a manufacturer of a JAI M4+ CL can be divided into several groups. They are, among others:
- JAI technical drawings
- M4+ CL manuals
- JAI product data sheets
- information booklets
- or energy labels JAI M4+ CL
All of them are important, but the most important information from the point of view of use of the device are in the user manual JAI M4+ CL.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals JAI M4+ CL, service manual, brief instructions and user manuals JAI M4+ CL. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product JAI M4+ CL.

Similar manuals

A complete manual for the device JAI M4+ CL, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use JAI M4+ CL by users. Manuals are usually written by a technical writer, but in a language understandable to all users of JAI M4+ CL.

A complete JAI manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual JAI M4+ CL - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the JAI M4+ CL, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the JAI M4+ CL, that we can find in the current document
3. Tips how to use the basic functions of the device JAI M4+ CL - which should help us in our first steps of using JAI M4+ CL
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with JAI M4+ CL
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of JAI M4+ CL in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning JAI M4+ CL?

Use the form below

If you did not solve your problem by using a manual JAI M4+ CL, ask a question using the form below. If a user had a similar problem with JAI M4+ CL it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)