English dropdown-ico

Manual RedMax EXZ2500S-BC

64 pages 1.7 mb
Download

Go to site of 64

Summary
  • RedMax EXZ2500S-BC - page 1

    OWNER / OPERA T OR MANUAL EXtreme™ T3087-93110 (303) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING EXZ-PU 302845 and up EX-B ...

  • RedMax EXZ2500S-BC - page 2

    ...

  • RedMax EXZ2500S-BC - page 3

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • RedMax EXZ2500S-BC - page 4

    1. Parts location EX-BC EX-PS EX-LRT EX-HE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1. Loop handle 2. Shoulder strap hanger 3. Ignition switch 4. Throttle cable 5. Throttle lever 6. Throttle set button 7. Drive shaft housing 8. Knob bolt 9. Spark arrester 10. Starter knob 11. Fuel tank 12. Primer pump 13. Choke lever 14. ...

  • RedMax EXZ2500S-BC - page 5

    2. Specifications Engine Type ······················································································ Air-cooled 2-stroke gasoline Model ························································ ...

  • RedMax EXZ2500S-BC - page 6

     6  (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) Keep all children, bystanders and helpers 15 meters away from the machine. If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to ord ...

  • RedMax EXZ2500S-BC - page 7

    For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: AIR CLEAN ...

  • RedMax EXZ2500S-BC - page 8

     8  5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the ...

  • RedMax EXZ2500S-BC - page 9

    b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product. ■ WO ...

  • RedMax EXZ2500S-BC - page 10

     10  ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more ...

  • RedMax EXZ2500S-BC - page 11

    Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit ...

  • RedMax EXZ2500S-BC - page 12

     12  • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. ■ MAIN ...

  • RedMax EXZ2500S-BC - page 13

    5. For safe operation refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank. 3. When refilling the tank, always turn off the engine and allow it to cool ...

  • RedMax EXZ2500S-BC - page 14

     14  ■ MOUNTING ENGINE (SE1) 1. Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears. 2. Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When di ...

  • RedMax EXZ2500S-BC - page 15

    6. Set up (EX-BC only) EX-BC SE2 ■ INSTALLING DEBRIS GUARD • Put the debris guard on the gear box, attach it with the 4 screws and hardware provided. (SE1) (1) debris guard (2) plate (3) screw ■ INSTALLING CUTTING HEAD (SE2) 1. While locking the gear shaft, by inserting the supplied tool into the upper holder on the gear box, loosen and remov ...

  • RedMax EXZ2500S-BC - page 16

    6. Set up (EX-LRT only) EX-LRT SE1 ■ ATTACHING THE TRIMMING MECHANISM (SE1) 1. Remove the screw screwed into the end of the trimming mechanism. 2. Insert the end of the trimming mechanism into the main pipe. 3. Line up the hole on the end of the trimming mechanism into which the screw is to be inserted with the hole on the main pipe, and screw th ...

  • RedMax EXZ2500S-BC - page 17

    6. Set up (EX-PS only) (1) (2) (3) (4) (5) EX-PS SE1 EX-PS SE2 EX-PS SE3 ■ ATTACHING THE PRUNING MECHANISM (SE1) 1. Remove the cap on the end of the main pipe. 2. Remove the screw screwed into the end of the gear case. 3. Insert the end of the gear case into the main pipe. 4. Line up the hole on the end of the gear case into which the screw is to ...

  • RedMax EXZ2500S-BC - page 18

    6. Set up (EX-PS only) 3. Fit the chain tensioner nut into the lower hole of the guide bar, then install the chain cover, and fasten the mounting nut to finger tightness. (SE3)(SE4) (1) Hole (2) Moving direction (3) Chain tensioner nut 4. Adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the ...

  • RedMax EXZ2500S-BC - page 19

    6. Set up (EX-HE only) EX-HE SE1 EX-HE SE2 EX-HE SE3 EX-HE SE4 1. Insert the driveshaft into the clutch drum, then attach the gearbox to the shaft tube as aligning the positioning holes. Wipe out grease on the tube and the inside of the gearbox. Screw in the lock screw and fasten the clamp bolt firmly. (SE1) (1) Clamp bolt (2) Lock screw 2.Install ...

  • RedMax EXZ2500S-BC - page 20

     20  • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m(10ft) away from the fueling point before starting the engine. • The RedMax engines are lubricated by oil specially ...

  • RedMax EXZ2500S-BC - page 21

    container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification. ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a dustless place. 2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel spillage ...

  • RedMax EXZ2500S-BC - page 22

     22  (EX-HE only) ■ STARTING ENGINE The RedMax stick edger is designed for edging lawn in gardens, parks, roadsides and so on. Before starting the engine, take the operating position and adjust the handle position and the wheel height as necessary. ADJUSTING HANDLE POSITION • Loosen the handle bracket screws and re- position the handle to ...

  • RedMax EXZ2500S-BC - page 23

    8. Operation lever is in to the “start” position. (OP6) 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. (OP7) (1) choke lever (2) close (3) open (4) ignition switch (5) start (6) stop (7) throttle set button The product is equipped with a centrifugal clutch mechanism, so the cutting attachment begins to r ...

  • RedMax EXZ2500S-BC - page 24

    • Except for an emergency, avoid stopping the engine while pulling the throttle lever. ■ ADJUSTING THROTTLE CABLE • The normal play is 1 or 2mm when measured at the carburetor side end. Readjust with the cable adjuster as required. (OP9) (1) cable adjuster ■ ADJUSTING IDLING SPEED (OP10) 1. When the engine tends stop frequently at idling mo ...

  • RedMax EXZ2500S-BC - page 25

    8. Operation (EX-BC only) EX-BC OP1  25  ■ CUTTING WORK (LINE HEAD USAGE) 1. Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. 2. Keep the debris guard in place at all times when the unit is operated. TRIMM ...

  • RedMax EXZ2500S-BC - page 26

    Under growth Heavy weeds Light weeds Grass Nylon line head CUTTER APPLICATION CHART 9” 22-tooth: SST229 9” 24-tooth: SST249 8” 8-tooth: SGB088 9” 8-tooth: SGB089 8” 4-tooth: SGB048 9” 4-tooth: SGB049 8. Operation (Optional blade usage EX-BC only) ■ CHOOSE THE BLADE Choose a suitable recommended cutting attachment according to the obje ...

  • RedMax EXZ2500S-BC - page 27

     27  8. Operation (Optional blade usage EX-BC only) Change the loop handle to the J-handle for safe operation. (OP4) (1) Bracket: 3583-14101 (2) J-handle: 6367-14200 ■ STARTING THE ENGINE Please refer 5.For safe operation (P.10~12), 8.Operation (P.22~23). • The product is equipped with a centrifugal clutch mechanism, so the cutting attach ...

  • RedMax EXZ2500S-BC - page 28

    8. Operation (Optional blade usage EX-BC only) ■ OPERATION 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2. Be sure that the blade and the holder have been fastened according to instruction and the blade turns smoothly without abnormal noise. (OP7) • The rotating parts fastened incorrectly may cause s ...

  • RedMax EXZ2500S-BC - page 29

     29  2. How you can reduce the chance of kick out: a. Recognize that kick out can happen. By understanding and knowing about bounce, you can help eliminate the element of surprise. b. Cut fibrous weeds and grass only. Do not let the blade contact materials it cannot cut such as hard, woody vines and brush or rocks, fences, metal, etc c. Be ex ...

  • RedMax EXZ2500S-BC - page 30

    8. Operation (Optional blade usage EX-BC only)  30  EX-BC OP9 ■ MAINTENANCE BLADE • Check the blade and the fasteners for looseness, cracking, or bending. • Check the cutting edges and reform with a flat file. Point (OP9) : 1. Keep the end corner sharp. 2. Round the root of the edge, using round file. 3. Do not use water when using a gr ...

  • RedMax EXZ2500S-BC - page 31

    8. Operation (EX-LRT only)  31  This product is equipped with extremely sharp blades, and when used improperly these blades can be extremely dangerous, and improper handling can cause accidents which may in turn lead to serious injury or death. For this reason, you should always be careful to follow the following instructions when using your ...

  • RedMax EXZ2500S-BC - page 32

    EX-PS OP1 EX-PS OP2 ■ CHECKING OIL SUPPLY After starting the engine, run the chain at medium speed and see if chain oil is scattered off as shown in the figure. (OP1) (1) Chain oil The oil reservoir has a capacity sufficient to provide about 40 minutes of cutting time (when set to deliver the minimum flow rate, or about as long as you'll get ...

  • RedMax EXZ2500S-BC - page 33

    8. Operation (EX-PS only) The oil flow adjusting screw must be pressed in slightly in order to turn. Failure to do so could damage the pump and screw. 3. With a screwdriver, push in on the oil flow rate adjusting screw and turn in the desired direction (there are three incremental settings): (a) Clockwise-decrease lubrication. (b) Counter clockwise ...

  • RedMax EXZ2500S-BC - page 34

    EX-HE OP1 8. Operation (EX-HE only) • Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury. • Keep the blade guard and the mad guard attached in place at all times when the unit is operated. • Before starting a j ...

  • RedMax EXZ2500S-BC - page 35

    9. Maintenance every every every 25 50 100 system/compornent procedure before hours hours hours note use after after after fuel leaks, fuel spillage wipe out ✔ fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary see ■ ADJUSTING replace carburetor idle adjusting screw ✔ IDLING SPEED (p.24) if necessary clean and readj ...

  • RedMax EXZ2500S-BC - page 36

     36  •M ake sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry co ...

  • RedMax EXZ2500S-BC - page 37

    ■ MUFFLER • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, stop using the machine and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent re ...

  • RedMax EXZ2500S-BC - page 38

    9. Maintenance brushcutter. Note that it is necessary to remove the engine cover shown in (MA5) in order to be able to view the upper part of the cylinder. • If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on ...

  • RedMax EXZ2500S-BC - page 39

    9. Maintenance (EX-BC only) EX-BC MA1 EX-BC MA2 EX-BC MA3 EX-BC MA4 ■ REFILLING TRIMMING LINE 1. For replacement line, use a diameter of .095 in(2.4mm). The spool is capable for a line upto 27ft(8m)on the 4” head, and 46ft(14m)on the 6” head. Avoid using a larger line as it may cut down the trimming performance. For safety reasons, do not use ...

  • RedMax EXZ2500S-BC - page 40

    9. Maintenance (EX-LRT only) ■ BLADES (MA1) •W hen refilling the tank or resting, it is often a good idea to use the time to oil the cutting blades. • If a gap exists between the upper and lower blades, follow the procedure below to adjust them so that they fit more closely together. 1. Loosen lock nut (A) as shown in the diagram. 2. Tighten ...

  • RedMax EXZ2500S-BC - page 41

    9. Maintenance (EX-PS only) (1) EX-PS MA1 EX-PS MA2 EX-PS MA3 ■ OILING PORT Dismount the guide bar and check the oiling port for clogging. (MA1) (1) Oiling port ■ GUIDE BAR Remove sawdust in the bar groove and the oiling port. (MA2) (1) Groove (2) Oiling port (Type: Sprocket nose) Grease the nose sprocket from the feeding port on the tip of the ...

  • RedMax EXZ2500S-BC - page 42

    9. Maintenance (EX-PS only) The bar rail should always be a square. Check for wear of the bar rail. Apply a ruler to the bar and the outside of a cutter. If a gap is observed between them, the rail is normal. Otherwise, the bar rail is worn. Such a bar needs to be corrected or replaced.(MA4) (1) Ruler (2) Gap (3) No gap (4) Chain tilts ■ SPROCKET ...

  • RedMax EXZ2500S-BC - page 43

    9. Maintenance (EX-PS only) After every cutter has been set, check the depth gauge and file it to the proper level as illustrated. (MA7) Be sure to round off the front edge to reduce the chance of kickback or tie-strap breakage. (1) Appropriate gauge checker (2) Make the shoulder round (3) Depth gauge standard Make sure every cutter has the same le ...

  • RedMax EXZ2500S-BC - page 44

    9. Maintenance (EX-HE only) ■ GEAR CASE • The reduction gears are lubricated by multipurpose, lithium-based grease in the gear case. At every 20 hours of use, supply the gear case with new grease. • Remove the cutter holders before installing new grease to arrange for old grease to exit. • When removing and installing the cutter holder(a), ...

  • RedMax EXZ2500S-BC - page 45

    10. Storage • Aged fuel is one of major causes of engine starting failure. Before storing the unit, empty the fuel tank and run the engine until it uses all the fuel left in the fuel line and the carburetor. Store the unit indoor taking necessary measures for rust prevention.  45  ...

  • RedMax EXZ2500S-BC - page 46

     46  11 . T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ➞ clean/dry ? ...

  • RedMax EXZ2500S-BC - page 47

    12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and th ...

  • RedMax EXZ2500S-BC - page 48

    12. Parts list  48  Fig.1 EXZ-PU (S/N 302845 and up) ...

  • RedMax EXZ2500S-BC - page 49

    Key# Description Part Number Q'ty 1 PIPE-COMP, ø24x750 T3075-12100 1 2 SHAFT, 786x7 T3075-12210 1 3 SPACER 6036-12250 1 4 JOINT, PIPE-ASS’Y T3087-12400 1 5• JOINT T3087-12410 1 6• KNOBBOLT 6036-12420 1 7• WASHER 01643-30823 1 8• BOLT 01252-30510 1 9• BOLT 3540-13260 1 10 GRIP 3577-32141 1 11 LEVER-COMP T3002-12202 1 12 • COVER C ...

  • RedMax EXZ2500S-BC - page 50

    12. Parts list  50  Fig.2 EX-BC (S/N 302960 and up) ...

  • RedMax EXZ2500S-BC - page 51

    Key# Description Part Number Q'ty 1 GEARCASE-ASSY T3002-13001 1 2• GEARCASE 6489-13110 1 3• BEARING T3300-13521 1 4• BEARING T3403-13510 1 5• RING 04065-02612 1 6• SEAL 3565-13130 1 7• SHAFT T3002-13210 1 8• GEAR 6440-13220 1 9• NUT, M10 T3002-13260 1 10 • PINION T3002-13310 1 11 • BEARING T3300-13531 1 12 • BEARING T3403 ...

  • RedMax EXZ2500S-BC - page 52

    Fig.3 ENGINE UNIT (352001 and up)  52  12. Parts list ...

  • RedMax EXZ2500S-BC - page 53

     53  Key# Description Part Number Q'ty 1 CYLINDER 4810-12111 1 2 GASKET, base 4810-12210 1 3B OLT, M5x22 1850-12130 2 4 INSULATOR 4810-13162 1 5 GASKET, insulator 4810-13120 1 6G ASKET, carburetor 4810-13130 1 7 SCREW, M5x20 0263-90520 1 8 REEDVALVE (S)-A 4810-16100 1 9• VALVECASE (S) 4810-16110 1 10 • REEDVALVE 4810-16120 1 11 • S ...

  • RedMax EXZ2500S-BC - page 54

    12. Parts list  54  Fig.4 EX-LRT (S/N 000531 and up) ...

  • RedMax EXZ2500S-BC - page 55

    Key# Description Part Number Q'ty 1 LEVER, clamp 6598-13110 1 2 WASHER M6 0290-20615 1 3 WASHER 6x15x2.0 6782-13650 1 4 ANGLE ADJUSTER 6782-13141 1 5 BOLT M6x12 0225-10612 2 6 CASING A SET 6782-13200 1 7• CASING A ––––––––– 1 8• PLATE 6782-13220 1 9 GREESE FITTING 3199-13350 3 10 LABEL 6782-13250 1 11 SCREW M4x8 0263-1040 ...

  • RedMax EXZ2500S-BC - page 56

    12. Parts list  56  Fig.5 EX-PS (S/N 000000 and up) ...

  • RedMax EXZ2500S-BC - page 57

    Key# Description Part Number Q'ty 1 GEAR CASE (L)COMP T3073-13100 1 2• BEARING 06004-06001 1 3 GEAR CASE (R)COMP T3073-13200 1 4• BEARING 06002-00627 1 5 BOLT 01252-30512 5 6 FITTING 3199-13350 1 7 SCREW, tensioner T3073-13310 1 8 NUT, tensioner T3073-13320 1 9 BOLT 01252-30630 1 10 SHIM T3073-13250 1 11 BOLT 3245-11350 1 12 CHAIN COVER T3 ...

  • RedMax EXZ2500S-BC - page 58

    12. Parts list  58  Fig.6 EX-HE (S/N 000101 and up) ...

  • RedMax EXZ2500S-BC - page 59

    Key# Description Part Number Q'ty 1 GEARCASE-ASS’Y 6367-13000 1 2• GEARCASE 6367-13110 1 3• O-RING 6367-13150 1 4• BEARING 06000-06201 1 5• SEAL 3180-13141 1 6• RING 04065-03212 1 7• SHAFT 3541-13212 1 8• GEAR 6367-13130 1 9• PINION 6367-13140 1 10 • BEARING 06000-00609 1 11 • BEARING 06001-00609 1 12 • RING 04065-02412 ...

  • RedMax EXZ2500S-BC - page 60

    The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the emission control system warranty on your 1995 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on ...

  • RedMax EXZ2500S-BC - page 61

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: THE CARBURETOR ...

  • RedMax EXZ2500S-BC - page 62

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • RedMax EXZ2500S-BC - page 63

    ...

  • RedMax EXZ2500S-BC - page 64

    KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 ©P rinted in Japan ...

Manufacturer RedMax Category Trimmer

Documents that we receive from a manufacturer of a RedMax EXZ2500S-BC can be divided into several groups. They are, among others:
- RedMax technical drawings
- EXZ2500S-BC manuals
- RedMax product data sheets
- information booklets
- or energy labels RedMax EXZ2500S-BC
All of them are important, but the most important information from the point of view of use of the device are in the user manual RedMax EXZ2500S-BC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals RedMax EXZ2500S-BC, service manual, brief instructions and user manuals RedMax EXZ2500S-BC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product RedMax EXZ2500S-BC.

Similar manuals

A complete manual for the device RedMax EXZ2500S-BC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use RedMax EXZ2500S-BC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of RedMax EXZ2500S-BC.

A complete RedMax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual RedMax EXZ2500S-BC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the RedMax EXZ2500S-BC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the RedMax EXZ2500S-BC, that we can find in the current document
3. Tips how to use the basic functions of the device RedMax EXZ2500S-BC - which should help us in our first steps of using RedMax EXZ2500S-BC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with RedMax EXZ2500S-BC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of RedMax EXZ2500S-BC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning RedMax EXZ2500S-BC?

Use the form below

If you did not solve your problem by using a manual RedMax EXZ2500S-BC, ask a question using the form below. If a user had a similar problem with RedMax EXZ2500S-BC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)