English dropdown-ico

Manual Jet XACTA

16 pages 2.07 mb
Download

Go to site of 16

Summary
  • Jet XACTA - page 1

    Owner's Manual XACTA ® Fence II Commercial 30/50 WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No. M-708950Z Ph.: 800-274-6848 Revision H 03/06 www.wmhtoolgroup.com Copyright © WMH Tool Group This Manual is Bookmarked ...

  • Jet XACTA - page 2

    2 WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers lo cated throughout the United States can giv e you qu ick service. In most cases, any of these WMH Tool Group Authorized Servic e Centers can authorize warranty repair, assist you in obtai ...

  • Jet XACTA - page 3

    3 Table of Contents WARRANTY A ND SERVICE ........................................................................................................... ............. 2 Table of Contents .............................................................................................................. ............................ 3 Warnings ............... ...

  • Jet XACTA - page 4

    4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Rea d and understand the warnings posted on the mach ine and in this manual. Failure to comply with all of these warnings may cause seri ous injury. 3. Replace the warning labels if they become obscu red or removed. 4. The Table Saw on which the ...

  • Jet XACTA - page 5

    5 21. Keep visitors a safe distance from the work area. Keep children away. 22. Make your workshop child proof with padlocks , master switch es or by removing starter keys. 23. Give your work undivided attention. Looking ar ound, carrying on a conversatio n and “horse-play” are careless acts that can result in serious inj ury. 24. Maintain a ba ...

  • Jet XACTA - page 6

    6 Unpacking Open shipping carton s and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manu al thoroughly for assembly, alignment, and ma intenance instructions. Contents of the Shipping Containers 1 XACTA Fence II 1 Front Rail 1 Rear Rail 1 Guide Rail 3 Black Plastic End Caps 1 Hardware Pack ...

  • Jet XACTA - page 7

    7 Installation Tools required 7/16" and 1/2" wrenches Cross point screwd river 3/16" hex wrench Adjustable square Hammer (or rubber mallet) Straight edge The following instructions are for in stalling the XACTA Fence II and Rail System on JET Models JTAS-10 and JTAS-12 series ta ble saws. The Rails should bolt up to the JET sa w with ...

  • Jet XACTA - page 8

    8 Back Rail Installation 1. Locate the back rail which is 2" x 2" with holes running along one side onl y. The height of the back rail when attached to the saw is not critical. 2. Align the holes in the back rail to the holes in the table top, as shown in Figure 4. 3. Secure the back rail to the pre -tapped holes in the saw table (B, C, F ...

  • Jet XACTA - page 9

    9 Wooden Extension Table The wooden extension table is an optional accessory. Tools required Electric drill Cross point screwd river 7/16" and 1/2" wrenches Four clamps Straight edge Hammer (or rubber mallet) Installation The optional wood extension table (in cluding the optional router table) sits flush against the saw table and along th ...

  • Jet XACTA - page 10

    10 as shown in Figure 10. Finger tighten only. 5. Install three 1/4-20 x 1-1/2 hex cap screws, three 1/4 flat washers, and three 1/4 nuts into the holes in the rear edge of extension table as shown in Figure 11. Finger-tighten only. 6. Re-check the table for alignment, make further adjustments if necessary, then tighten all screws and nuts. 7. Moun ...

  • Jet XACTA - page 11

    11 XACTA Fence Screw the lock lever knob into the threaded handle on the XACTA Fence II as shown in Figure 14. The lock lever has three function al positions as shown in Figure 15: • The upright position permits mountin g and removal of fence from the saw. • The unlock position permit s easy fence positioning. • The lower position locks the f ...

  • Jet XACTA - page 12

    12 Adjusting Fence Parallel to the Miter Slot 1. Place the fence next to the outside edge of the right miter slot and lock it. 2. The fence should be even with the miter slot from front to back. 3. If the fence is not even along the length of the miter slot, unlock the fence, remove it and turn upside down. 4. Adjust one of the two setscrews (A, Fi ...

  • Jet XACTA - page 13

    13 Parts for the XACTA Fence II Commercial 30/50 Index No. Part No. Description Size Qty 1 ............... XF2-101 ................... Left Side Plate ...................................................... ................ .................... 1 2 ............... XF2-102 ................... Fence Body Assembly ...................................... ...

  • Jet XACTA - page 14

    14 Parts for the XACTA Fence II Rail Assembly Index No. Part No. Description Size Qty 1 ............... XF2-201 ................... Front Rail (50”) ..................................................... ................ .................... 1 ................. XF2-201A ................. Front Rail (30”) ......................................... ...

  • Jet XACTA - page 15

    15 Parts for the XACTA Fence II Leg Assembly Index No. Part No. Description Size Qty 1 ............... XF2-301 ................... Leg ....................................................................... ........... ......................... 2 2 ............... TS-0561031 ............. Hex Nut .................................................... ...

  • Jet XACTA - page 16

    16 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m ...

Manufacturer Jet Category Saw

Documents that we receive from a manufacturer of a Jet XACTA can be divided into several groups. They are, among others:
- Jet technical drawings
- XACTA manuals
- Jet product data sheets
- information booklets
- or energy labels Jet XACTA
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jet XACTA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jet XACTA, service manual, brief instructions and user manuals Jet XACTA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jet XACTA.

Similar manuals

A complete manual for the device Jet XACTA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jet XACTA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jet XACTA.

A complete Jet manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jet XACTA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jet XACTA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jet XACTA, that we can find in the current document
3. Tips how to use the basic functions of the device Jet XACTA - which should help us in our first steps of using Jet XACTA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jet XACTA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jet XACTA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jet XACTA?

Use the form below

If you did not solve your problem by using a manual Jet XACTA, ask a question using the form below. If a user had a similar problem with Jet XACTA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)