English dropdown-ico

Manual Quantum Atlas II

8 pages 0.52 mb
Download

Go to site of 8

Summary
  • Quantum Atlas II - page 1

    Atlas II Jumper Settings 50-pin Jumper Settings Jumper Settings The following describes the jumper options and setting s available on the Maxtor® Atlas™ II disk drive. Maxtor Atlas II was developed by Quantum Corp oration prior to its merger with Maxtor. Termination Enable (TE) Enable termination TE jumper on Disable termination TE jumper off 1 ...

  • Quantum Atlas II - page 2

    Atlas II Jumper Settings Termination Power (TP) Enable termination power TP jumper on Disable term ination power TP jum per off SCSI ID (A3, A2, A1, A0) Set drive SCSI ID See ID settings table below Delay Spin (DS) Enable spin delay SP jumper off Disable spin delay SP jumper on cStagger Spin Enable spin stagger SS jumper on Disable spin stagger SS ...

  • Quantum Atlas II - page 3

    Atlas II Jumper Settings 28-Pin Secondary Option Connector Pin S ignal P in S ignal 1 A0 2 logic_gnd 3 A1 4 logic_gnd 5 A2 6 logic_gnd 7 Fault LED 8 key (blank) 9 Busy LED 1 0 Spindle Sync 11 +5VDC out 1 2 unused 13 Delay Spin 1 4 logic_gnd 15 Stagger Spin 1 6 logic_gnd 17 Write Protect 1 8 logic_gnd 19 Spindle Sync 2 0 logic_gn The drawing above d ...

  • Quantum Atlas II - page 4

    Atlas II Jumper Settings SCSI ID Settings The following table identifies the va rious SCSI ID values and the jumper positions required to set them. Drive ID A0 A1 A2 ID 0 OFF OFF OFF ID 1 ON OFF OFF ID 2 OFF ON OFF ID 3 ON ON OFF ID 4 OFF OFF ON ID 5 ON OFF ON ID 6 OFF ON ON ID 7 ON ON ON 4 of 8 ...

  • Quantum Atlas II - page 5

    Atlas II Jumper Settings 68-pin Jumper Settings Jumper Settings The following describes the jumper option s and settings available on the Maxtor® At las™ II disk drive. Maxtor Atlas II was developed by Quantum Corporation pr ior to its merger with Maxtor. Termination Enable (TE) Enable termination TE jumper on Disable termination TE jumper off N ...

  • Quantum Atlas II - page 6

    Atlas II Jumper Settings 6 of 8 Stagger Spin Enable spin stagger SS jumper on Disable spin stagger SS jumper off Write Protect Enable Write Protection WP jumper on Disable W rite Protection WP jumper off Jumper Locations The Atlas II wide disk drive has two locations where user configurable jumpers ar e found. The primary jumper block (Front option ...

  • Quantum Atlas II - page 7

    Atlas II Jumper Settings 7 of 8 Pin Signal Pin Signal 1 A3 2 l ogic_gnd 3 A2 4 l ogic_gnd 5 A1 6 l ogic_gnd 7 A0 8 l ogic_gnd 9 Key (blank) 1 0 F ault LED 11 Delay Spin 1 2 l ogic_gnd 13 Logic ground 1 4 E nable Active Termination 15 Spindle Sync 1 6 S pindle Sync 17 Busy Led 1 8 + 5VDC out 19 W rite Protect 2 0 l ogic_gnd 21 Stagger Spin 2 2 l ogi ...

  • Quantum Atlas II - page 8

    Atlas II Jumper Settings Atlas II 9.1GB WD SCSI ID Settings The following table identifies the various SCSI ID values and the jumper positions required to set them. Drive ID A0 A1 A2 A3 ID 0 OFF OFF OFF OFF ID 1 ON OFF OFF OFF ID 2 OFF ON OFF OFF ID 3 ON ON OFF OFF ID 4 OFF OFF ON OFF ID 5 ON OFF ON OFF ID 6 OFF ON ON OFF ID 7 ON ON ON OFF ID 8 OFF ...

Manufacturer Quantum Category Computer Drive

Documents that we receive from a manufacturer of a Quantum Atlas II can be divided into several groups. They are, among others:
- Quantum technical drawings
- Atlas II manuals
- Quantum product data sheets
- information booklets
- or energy labels Quantum Atlas II
All of them are important, but the most important information from the point of view of use of the device are in the user manual Quantum Atlas II.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Quantum Atlas II, service manual, brief instructions and user manuals Quantum Atlas II. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Quantum Atlas II.

Similar manuals

A complete manual for the device Quantum Atlas II, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Quantum Atlas II by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Quantum Atlas II.

A complete Quantum manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Quantum Atlas II - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Quantum Atlas II, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Quantum Atlas II, that we can find in the current document
3. Tips how to use the basic functions of the device Quantum Atlas II - which should help us in our first steps of using Quantum Atlas II
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Quantum Atlas II
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Quantum Atlas II in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Quantum Atlas II?

Use the form below

If you did not solve your problem by using a manual Quantum Atlas II, ask a question using the form below. If a user had a similar problem with Quantum Atlas II it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)