English dropdown-ico

Manual Makita EBH253U

28 pages 4.85 mb
Download

Go to site of 28

Summary
  • Makita EBH253U - page 1

    EBH252U EBH253U EBH252L EBH253L P etr ol Br ushcutter EBH252U EBH253U EBH252L EBH253L ORIGINAL INSTRUCTION MANUAL Important: Read this instruction manual carefully before putting the Petrol Brushcutter into operation and strictly observe the safety regulations! Preserve instruction manual carefully! ...

  • Makita EBH253U - page 2

    2 Thank you very much for purchasing the MAKIT A Petrol Brushcutter . We are pleased to recommend to you the MAKIT A Petrol Brushcutter which is the result of a long development programme and many years of knowledge and experience. Please read this booklet which refers in detail to the various points that will demonstrate its outstanding performanc ...

  • Makita EBH253U - page 3

    3 General Instructions – T o ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the Petrol Brushcutter . Users insufciently informed will risk danger to themselves as well as others due to improper handling. – It is recommended only to lend the Petrol Brushcutter to people who hav ...

  • Makita EBH253U - page 4

    4 Start the Petrol Brushcutter only in accordance with the instructions. – Do not use any other methods for starting the engine! – Use the Petrol Brushcutter and the tools only for such applications as specied. – Only start the Petrol Brushcutter engine, after the entire assembly is done. Operation of the device is only permitted after all ...

  • Makita EBH253U - page 5

    5 Method of operation – Only use the Petrol Brushcutter in good light and visibility . During the winter season beware of slippery or wet areas, ice and snow (risk of slipping). Always ensure a safe footing. – Never cut above waist height. – Never stand on a ladder and run the Petrol Brushcutter . – Never climb up into trees to perform cutt ...

  • Makita EBH253U - page 6

    6 EC-DECLARA TION OF CONFORMITY Petrol Brushcutter: model EBH252U, EBH253U, EBH252L, EBH253L (See TECHNICAL DA T A for the specications) We declare under our sole responsibility that this product is in compliance with the following Directives, 2000/14/EC, 2006/42/EC. The most important standards applied to properly meet the requirements of the a ...

  • Makita EBH253U - page 7

    7 TECHNICAL D A T A EBH252U , EBH252L Model EBH252U EBH252L Bike handle Loop handle Dimensions: length x width x height (without cutting blade) mm 1,770 x 620 x 490 1,770 x 330 x 275 Mass (without plastic guard and cutting blade) kg 5.7 5.3 V olume (fuel tank) L 0.5 V olume (oil tank) L 0.08 Engine displacement cm 3 24.5 Maximum engine performance ...

  • Makita EBH253U - page 8

    8 TECHNICAL D A T A EBH253U , EBH253L Model EBH253U EBH253L Bike handle Loop handle Dimensions: length x width x height (without cutting blade) mm 1,770 x 620 x 490 1,770 x 330 x 275 Mass (without plastic guard and cutting blade) kg 5.9 5.4 V olume (fuel tank) L 0.5 V olume (oil tank) L 0.08 Engine displacement cm 3 24.5 Maximum engine performance ...

  • Makita EBH253U - page 9

    9 ⑱ ④ ⑤ ⑦ ⑧ ⑨ ⑪ ⑩ ⑫ ⑬ ⑭ ⑮ ④ ⑤ ⑰ ⑦ ⑨ ⑪ ⑩ ⑫ ⑭ ⑯ EBH252L EBH253L EBH252U EBH253U ① ③ ⑥ ⑲ ② 2 2 2 1 DESIGNA TION OF P AR TS GB DESIGNA TION OF P ARTS 1 Fuel tank 2 Rewind starter 3 Air cleaner 4 I-O switch (on/of f) 5 Spark plug 6 Exhaust mufer 7 Clutch case 8 Rear grip 9 Hanger 10 Handle 1 1 Con ...

  • Makita EBH253U - page 10

    10 CAUTION: Before doing any work on the Petrol Brushcutter , always stop the engine and pull the spark plug connector off the spark plug. Always wear protective gloves! CAUTION: Start the Petrol Brushcutter only after having assembled it completely . For machines with bike handle models – Loosen knob (1). – Place handle (4) between handle clam ...

  • Makita EBH253U - page 11

    11 T o meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine MAKIT A cutter blades or nylon cutting head. – The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check t ...

  • Makita EBH253U - page 12

    12 T urn the machine upside down, and you can replace the cutter blade or nylon cutting head easily . – Insert the hex wrench through the hole in the gear case and rotate the receiver washer (4) until it is locked with the hex wrench. – Loosen the nut (1) (left-hand thread) with the socket wrench and remove the nut (1), cup (2), and clamp washe ...

  • Makita EBH253U - page 13

    13 Inspection and rell of engine oil – Perform the following procedure, with the engine cooled down. – While keeping the engine level, remove the oil gauge, and conrm that the oil is lled within the upper and lower limit marks. When the oil is in short in such a way that the oil gauge touches the oil only by its tip, in particular with ...

  • Makita EBH253U - page 14

    14 REFUELING Handling of fuel It is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be performed in a sufciently ventilated room or in the open air . Never inhale fuel vapor , and keep fuel away from you. If you touch fuel repeatedly or for a long time, the skin becomes dry , which may c ...

  • Makita EBH253U - page 15

    15 Attachment of shoulder strap – Adjust the strap length so that the cutter blade will be kept parallel with the ground. For EBH252U, EBH253U NOTE: Be careful not to trap clothing, etc., in the buckle. Observe the applicable accident prevention regulations! ST ARTING Move at least 3 m away from the place of refuelling. Place the Petrol Brushcutt ...

  • Makita EBH253U - page 16

    16 2) Set the I-O switch (1) to OPERA TION. 3) Choke lever Close the choke lever . Choke opening: – Full closing in cold or when the engine is cold. – Full or half opening in restart just after stop of operation. Note: – If the starter handle is pulled repeatedly when the choke lever remains at “CLOSE” position, the engine will not start ...

  • Makita EBH253U - page 17

    17 B: Startup after warm-up operation 1) Push the primer pump repeatedly . 2) Keep the throttle lever at the idling position. 3) Pull the recoil starter strongly . 4) If it is difcult to start the engine, open the throttle by about 1/3. Pay attention to the cutter blade which may rotate. ST OPPING 1) Release the throttle lever (2) fully , and wh ...

  • Makita EBH253U - page 18

    18 NYLON CUTTING HEAD The nylon cutting head is a dual string trimmer head capable of both automatic and bump & feed mechanisms. The nylon cutting head will automatically feed out the proper length of nylon cord by the changes in centrifugal force caused by increasing or decreasing rpms. However , to cut soft grass more efciently , bump the ...

  • Makita EBH253U - page 19

    19 REPLACEMENT OF ENGINE OIL Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the period and quantity of replacement. A TTENTION: In general, the engine main unit and engine oil still remain hot just after the engine is stopped. In replacement of oil, conrm that the engine main u ...

  • Makita EBH253U - page 20

    20 CLEANING OF AIR CLEANER DANGER: INFLAMMABLES STRICTL Y PROHIBITED Interval of Cleaning and Inspection: Daily (every 10 operating hours) – T urn the choke lever to the full close side, and keep the carburetor off from dust or dirt. – Remove the air cleaner cover-xing bolts. – Pull the cover lower side and detach the air cleaner cover . ? ...

  • Makita EBH253U - page 21

    21 CLEANING OF FUEL FIL TER W ARNING: INFLAMMABLES STRICTL Y PROHIBITED Interval of Cleaning and Inspection: Monthly (every 50 operating hours) Suction head in the fuel tank – The fuel lter (1) of the suction head is used to lter the fuel required by the carburetor . – A periodical visual inspection of the fuel lter is to be conducted. ...

  • Makita EBH253U - page 22

    22 W ARNING: When draining the fuel, be sure to stop the engine and conrm that the engine cools down. Just after stopping the engine, it may still hot with possibility of burns, inammability and re. A TTENTION: When the machine is kept out of operation for a long time, drain up all fuel from the fuel tank and carburetor , and keep it at a ...

  • Makita EBH253U - page 23

    23 *1 Perform initial replacement after 20h operation. *2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop. *3 After emptying the fuel tank, continue to run the engine and drain fuel in the carburetor . Operating time Item Before operation Af t er lu b ri ca ti on Daily (10h) 30h 50h 200h Sh u td ow n/ re s ...

  • Makita EBH253U - page 24

    24 TROUBLESHOO TING Before making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the description of this manual. Never tamper or dismount any part contrary to the description. For repairs, contact Authorized Service Agent or local dealership. When the engine does not start after w ...

  • Makita EBH253U - page 25

    ...

  • Makita EBH253U - page 26

    ...

  • Makita EBH253U - page 27

    ...

  • Makita EBH253U - page 28

    Makita Corporation Anjo, Aichi, Japan 884909C228 ...

Manufacturer Makita Category Brush Cutter

Documents that we receive from a manufacturer of a Makita EBH253U can be divided into several groups. They are, among others:
- Makita technical drawings
- EBH253U manuals
- Makita product data sheets
- information booklets
- or energy labels Makita EBH253U
All of them are important, but the most important information from the point of view of use of the device are in the user manual Makita EBH253U.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Makita EBH253U, service manual, brief instructions and user manuals Makita EBH253U. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Makita EBH253U.

Similar manuals

A complete manual for the device Makita EBH253U, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Makita EBH253U by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Makita EBH253U.

A complete Makita manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Makita EBH253U - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Makita EBH253U, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Makita EBH253U, that we can find in the current document
3. Tips how to use the basic functions of the device Makita EBH253U - which should help us in our first steps of using Makita EBH253U
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Makita EBH253U
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Makita EBH253U in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Makita EBH253U?

Use the form below

If you did not solve your problem by using a manual Makita EBH253U, ask a question using the form below. If a user had a similar problem with Makita EBH253U it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)