English dropdown-ico

Manual Ice-O-Matic IOD200

13 pages 1.01 mb
Download

Go to site of 13

Summary
  • Ice-O-Matic IOD200 - page 1

    Mile High Equipment 11100 East 45th Av e Denver, Colorado 80239 Part Number 9081305-01 Print Date 06/02 MODELS-IOD150, IOD200 AND IOD250 ICE ONLY DISPENSERS SERVICE/INSTALLATION MANUAL ...

  • Ice-O-Matic IOD200 - page 2

    Introduction IOD150,IOD200,IOD250 To the owner or user: This produc t manual is a source of in formation about the installation, start up, cleaning, maint enance and repair o f the product. The IOD150, IOD200 and IOD250 are ice only counter top dispensers designed to use 22 inch wi de and 30 inch wide respectfully Ice-O-Matic cubed i ce machines as ...

  • Ice-O-Matic IOD200 - page 3

    Specifications and Limitati ons IOD150, IO D200, IOD250 Limita tion s: Must meet the same limitations as the cuber installed on top o f it: 5 0 ° F. air minimum 100 ° F. ai r ma xi mum Must be installed indoors. Must allow at least 6-inch clearance at the rear a nd both sides when using an air-cooled ice machine. Must allow space for the utility ...

  • Ice-O-Matic IOD200 - page 4

    For Th e Insta ller IOD150, IOD20 0, IOD250 Equipment Description The IOD150, IOD200 and IOD250 are counter top m ounted ice only dispensers. These units are designed to dispense cube ice only and hav e ice storag e capacities o f 150 lb.,220 lb. and 250 lb. respecti vely. Site Preparation The site chosen for the d ispenser must be capable o f supp ...

  • Ice-O-Matic IOD200 - page 5

    Installation IOD150, IOD200, IOD250 1. Locate the ice dispenser on the counter. Allow vertical clearance above the unit for the removal of the cover and for pouring ice into the hopper. 2. Plan the unit drain. A one-inch (1”) I.D. drain tube is required for draining. Routing is either through the back or the base. Sufficient fittings are included ...

  • Ice-O-Matic IOD200 - page 6

    Water Glass Filler Kit IOD150, IOD200, IOD250 Installation I nstructions WARNING: Disconnect power to unit before p roceeding with installation. 1. Prepare the unit as follows: · Remove the lower front panel · Locate faucet-mounting holes in the front panel. (Reference page 6 for hole locations) 2. Install faucet and tubing assembly as show n bel ...

  • Ice-O-Matic IOD200 - page 7

    Water Glass Filler Kit (Con’t) IOD150, IO D200, IOD250 Faucet mounting hole locations. IOD150 Dimens ions A 4.0 Inches B 2.5 Inches IOD200 and IOD 250 Dimensio ns A 6.125 Inches B 3.125 Inches The water inlet tubing can be routed either fr om the back or from underneath the dispenser. If from the back, rem ove the back and bottom access panels. P ...

  • Ice-O-Matic IOD200 - page 8

    Initial Start Up IOD150, IOD20 0, IOD250 1. Sanitize the ice storage system as ins tructed on Page 10 . 2. Fill the hopper with sanitary ice. 3. Plug the unit’s power cord into an electrical outlet and the li ghted sign should come on. 4. Dispense several containers of ice. Note: I n normal operation, pushing the ice dispenser mechanism will caus ...

  • Ice-O-Matic IOD200 - page 9

    Gate Restrictor Plate IOD150, IOD200, IOD250 CAUTION: Disconnect po wer to dispenser and ice mach ine before installing, remov ing or adjusting restrictor. AD J U S T M E N T This plate may be adjusted as shown to reduce or increase t he dispensing rate of ice, especially desirable when using glasses or o ther containers with small openings. Adjust ...

  • Ice-O-Matic IOD200 - page 10

    Cleaning and Sanitizing IOD150, I OD200, IOD250 The sink, grill and splash panel area should b e cl eaned daily. The following dispenser ma intenance should be performed at the int ervals indicated: Dail y (Or A s Required) Remove foreign material from vending area drip tray to prevent drain blockage. Weekly (Or A s Requi red) Clean vending area. C ...

  • Ice-O-Matic IOD200 - page 11

    Cleaning and Sanitizing IOD150, I OD200, IOD250 MONTHLY AND INITI AL START UP: Sanitize the Ice Storage System. Note: This should be done by qualified personnel. CLEANING PREC AUTIONS WA RNING : Disconnect Po wer Before Cleaning! Do not use me tal scrapers, sharp objects or abrasives on the ice storage hoppe r, top cov er and t he agitator disk, as ...

  • Ice-O-Matic IOD200 - page 12

    Troubleshooti ng IOD150, IOD200, IOD250 IMPOR TA NT: only qualified personnel should service internal components or electrical wiring. Should the dispenser fail to operate properly, check that there is power to the unit and that the hopper contains ice. If the unit does not dispense, check t he following chart under the appropriate symptoms to aid ...

  • Ice-O-Matic IOD200 - page 13

    Wiring Di agram IO D150, I OD200, IOD250 Page 12 ...

Manufacturer Ice-O-Matic Category Ice Maker

Documents that we receive from a manufacturer of a Ice-O-Matic IOD200 can be divided into several groups. They are, among others:
- Ice-O-Matic technical drawings
- IOD200 manuals
- Ice-O-Matic product data sheets
- information booklets
- or energy labels Ice-O-Matic IOD200
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ice-O-Matic IOD200.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ice-O-Matic IOD200, service manual, brief instructions and user manuals Ice-O-Matic IOD200. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ice-O-Matic IOD200.

Similar manuals

A complete manual for the device Ice-O-Matic IOD200, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ice-O-Matic IOD200 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ice-O-Matic IOD200.

A complete Ice-O-Matic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ice-O-Matic IOD200 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ice-O-Matic IOD200, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ice-O-Matic IOD200, that we can find in the current document
3. Tips how to use the basic functions of the device Ice-O-Matic IOD200 - which should help us in our first steps of using Ice-O-Matic IOD200
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ice-O-Matic IOD200
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ice-O-Matic IOD200 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ice-O-Matic IOD200?

Use the form below

If you did not solve your problem by using a manual Ice-O-Matic IOD200, ask a question using the form below. If a user had a similar problem with Ice-O-Matic IOD200 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)