English dropdown-ico

Manual Southbend SPR-2

21 pages 1.16 mb
Download

Go to site of 21

Summary
  • Southbend SPR-2 - page 1

    IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. MODEL # SERIAL # DATE PURCHASED OPERATOR’S MANUAL INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS STOCK POT RANGE MODEL: SPR-1, SPR-2, and SPR-3 Improper installation, adjustment, alteration, service, or maintenance can cause ...

  • Southbend SPR-2 - page 2

    SAFETY PRECAUTIONS Before installing and operating this equipment, be sure everyone involved in its operation is fully trained and aware of precau- tions. Accidents and problems can be caused by failure to follow fundamental rules and precautions. The following symbols, found throughout this manual, alert you to potentially dangerous conditions to ...

  • Southbend SPR-2 - page 3

    Congratulations! You have purchased one of the finest pieces of heavy-duty commercial cooking equipment on the market. You will find that your new equipment, like ail Southbend equipment, has been designed and manufactured to meet the tough- est standards in the industry. Each piece of Southbend equipment is carefully engineered and designs are ver ...

  • Southbend SPR-2 - page 4

    NOTE: Not for Scale. For Dimensional Purposes Only. -+- G f B i C T D E $ TOP VIEW SIDE VIEW FRONT VIEW Dimensions: ( ) = Millimeters NOTE: Above dimensions are for single Stock Pot Ranges. SPR-2 Double and SPR-3 Triple Stock Pot Ranges are shipped assembled at factory and above dimensions are different. UTILITY INFORMATION: One 3/4” connection r ...

  • Southbend SPR-2 - page 5

    NOTICE Southbend reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions, or replacements for previously purchased equipment. NOTICE These procedures must be followed by qualified personnel or warranty will be void. GENERAL: NOTICE The u ...

  • Southbend SPR-2 - page 6

    If this equipment is being installed at over 2,000 feet altitude and was not specified on order, contact the appropriate authorized Southbend Service Representative or the Southbend Service Department. Failure to install with proper ori- fice sizing will result in improper performance and may void the warranty. NOTICE If applicable, the vent line f ...

  • Southbend SPR-2 - page 7

    I NOTICE I I Proper ventilation is the owner’s responsibility. Any problem due to improper ventilation will not be covered by warranty. I A WARNING I improper ventilation can result in personal injury or death. Ventilation which fails to properly remove flue products can cause headaches, drowsiness, nausea, or could result in death. LEVELING: Uni ...

  • Southbend SPR-2 - page 8

    FIGURE 1 LEG ASSEMBLY NOTE: Items A, B, and C are installed at the factory. items D and E are to be installed in field. Flanged feet (item E) must go on to the rear of the unit. * 1179510 is a leg package consisting of 2 standard legs and 2 flanged legs. PAGE 6 ...

  • Southbend SPR-2 - page 9

    PERFORMANCE CHECK: The following items should be checked within the first 30 days of operation by a qualified service technician. 1. Verify equipment is level. 2. Check ventilation. 3. Check timers, switches and motor for proper installation and operation. 4. Check for any damage to unit from shipping or installation. 5. Check for proper clearance ...

  • Southbend SPR-2 - page 10

    THEORY OF OPERATION TO LIGHT STANDING PILOT: 1. Locate pilot adjustment screw. This is located between the burner valves and is accessable through the slotted hole in the control panel. 2. Verify the gas supply line is connected and gas is being supplied to the unit. 3. Light pilot and verii that the pilot flame is approximately l/4 “ high. 4. If ...

  • Southbend SPR-2 - page 11

    ADJUSTMENTS NOTICE Service work should be performed only by a qualified technician who is experienced in, and knowledgeable of, the operation of commercial gas, electric, and steam cooking equipment. Contact the Authorized Southbend Service Agency for reliable service, dependable advice or other assistance, and for genuine factory parts. Warranty w ...

  • Southbend SPR-2 - page 12

    MAINTENANCE Southbend equipment is sturdily constructed of the best materials and is designed to provide durable service when treated with ordinary care. To expect the best performance, your equipment must be kept in good condition and cleaned daily. Naturally, the periods for this care and cleaning depend on the amount and degree of use. Following ...

  • Southbend SPR-2 - page 13

    NOTICE INSTALLATION OF OTHER THAN GENUINE SOUTHBEND PARTS WILL VOID THE WARRANTY ON THIS EQUIPMENT. The serial plate with voltage, model, and serial information is located at the rear of the unit on the back panel. Refer to part number 1179452 in parts section “main body components” of this manual. There is also an Identification Plate mounted ...

  • Southbend SPR-2 - page 14

    FIGURE 2 MISCELLANEOUS PARTS TO AlTACH (2) SPR-1 UNITS Refer to figure 2 for parts list below. * SPR-2 requires 3 per pair of units. SPR-3 requires 6 total. PAGE 12 ...

  • Southbend SPR-2 - page 15

    MAIN BODY COMPONENTS Refer to figure 3 for parts list below. R 1179467 S 1179472 T 1179519 U 1179477 1 Frame Grate 2 Filler Strip for Side Liner 1 Shield, Screw 1 Side Liner, Right PAGE 13 ...

  • Southbend SPR-2 - page 16

    H- c D FIGURE 3 PAGE 14 ...

  • Southbend SPR-2 - page 17

    FIGURE 4 GAS LINE ASSEMBLY N 1160532 2 0 1179529 1 * Includes all items in figure 4, except items A, B, N, 0 Knob Pilot Bracket PAGE 15 ...

  • Southbend SPR-2 - page 18

    FIGURE 5 BURNER COMPONENTS OPTINAL ACCESORIES: ITEM PART NUMBER DESCRIPTION l 1179259 Wok Ring, Tall * 1179387 Wok Ring, Short l 1179388 Wok Pan, use with rings * Not Shown PAGE 16 ...

  • Southbend SPR-2 - page 19

    LIMITED WARRANTY Southbend warrants that the equipment, as supplied by the factory to the original purchaser, is free from defects in materials and workmanship. Should any part thereof become defective as a result of normal use within the period and limits defined below, then at the option of Southbend, such parts will be repaired or replaced by So ...

  • Southbend SPR-2 - page 20

    The @igoing wanmty is exclusive and in lieu oftdl other warn- exfmssd or implied 7hee are no irnpkc/ wanmties ofmetdmntabiky -ffitness*a~~W-P= m Southbend, hereinafter referred to as the seller, warrants equipment manufactured by it to be free from defects in material and workmanship for which it is responsible. The seller’s obliga- tion under th ...

  • Southbend SPR-2 - page 21

    A product with the Southbend name incorporates the best in durability and low maintenance. We all recognize however, that replacement parts and occasional professional service may be necessary to extend the useful life of this unit. When service is needed, contact a Southbend Authorized Service Agency, or your dealer. To avoid confusion, always ref ...

Manufacturer Southbend Category Range

Documents that we receive from a manufacturer of a Southbend SPR-2 can be divided into several groups. They are, among others:
- Southbend technical drawings
- SPR-2 manuals
- Southbend product data sheets
- information booklets
- or energy labels Southbend SPR-2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Southbend SPR-2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Southbend SPR-2, service manual, brief instructions and user manuals Southbend SPR-2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Southbend SPR-2.

Similar manuals

A complete manual for the device Southbend SPR-2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Southbend SPR-2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Southbend SPR-2.

A complete Southbend manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Southbend SPR-2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Southbend SPR-2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Southbend SPR-2, that we can find in the current document
3. Tips how to use the basic functions of the device Southbend SPR-2 - which should help us in our first steps of using Southbend SPR-2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Southbend SPR-2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Southbend SPR-2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Southbend SPR-2?

Use the form below

If you did not solve your problem by using a manual Southbend SPR-2, ask a question using the form below. If a user had a similar problem with Southbend SPR-2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)