-
Weber 900 LP - page 1
W E B E R W E B E R 900 LP Gas Barbecue Serial Number Please use this number in registering your warranty and any correspondence with the factory . Owner’ s Manual W ARNING: Do not try to light this appliance without reading "Lighting" instructions section of this manual. THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONL Y . NO TICE T ...
-
Weber 900 LP - page 2
2 D ANGER Failure to f ollow the Dangers, W arnings and Cautions contained in this Owner’ s Manual may result in serious bodil y injury or death, or in a fire or an explosion causing damage to property . W ARNINGS Do not store a spare or disconnected LP tank under or near this barbecue . Improper assemb ly ma y be dang er ous. Ple ...
-
Weber 900 LP - page 3
3 W ARRANTY Weber-Stephen Products Co. (W eber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue that it will be free of defects in material and workmanship from the date of purchase as follows: Aluminum Castings, 10 years, Flavorizer Bars, 3 years, Cast Iron Cooking Grates, 5 years, All Remaining Parts, 5 years, when assembled ...
-
Weber 900 LP - page 4
P A TENTS AND TRADEMARKS 4 © 1997 Weber . Weber , , Flavorizer and Crossover are registered U.S. trademarks; Spirit, Gas Catcher , FlameCheck, and Spider Stopper are U.S. trademarks of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266. U.S.A. Weber Gas Barbecues are covered under the following patent nos.: U.S.A. #4,677,96 ...
-
Weber 900 LP - page 5
5 Contents WARNINGS ................................................................ 2 W arranty & Patents .................................................. 3-4 General Instructions .................................................... 6 Assembly ............................................................... 7-21 Operating Instructions Lightin ...
-
Weber 900 LP - page 6
6 General Instructions Y our Weber Gas Barbecue is a portable outdoor cooking appliance. With the Weber Gas Barbecue you can grill, barbecue, roast and bake with results that are difficult to duplicate with indoor kitchen appliances. The closed lid and Flavorizer Bars produce that "outdoor" flavor in the food. The Weber Gas Barbecue is po ...
-
Weber 900 LP - page 7
7 Step 1 Check package contents Cooking box (assembly) Lid (assembly) LP tank Bottom tray Cooking grates (2) LP tank filler adapter Control panel Assembl y T ools needed Hammer 7/16 inch open-end or an adjustable wrench Pliers Block of wood Phillips screwdriver Supplies needed Y our LP tank is shipped empty for safety . After setting the LP fuel sc ...
-
Weber 900 LP - page 8
Left frame Right frame Wheel frame Leg frame Frame connector Work table Swing table assembly Support rod Accessory racks (2) W arming rack Flavorizer Bars (5) T ank panel assembly Front panel Catch pan holder Catch pan Drip pans (2) Manifold bracket Thermometer Wheels (2) Fuel scale assembly 8 W E B E R W E B E R W E B E R W E B E R ...
-
Weber 900 LP - page 9
Plastic buttons (2) (actual size) 1/4-20 wing nuts (2) (actual size) 1/4 inch nylon washers (1 1) Hair pin cotters (2) Wheel hubcaps (3) 1/4-20 keps nut Phillips screws/washers (2) Check contents of hardware packs Burner control knobs (3) T ool holders (3) T ubing plugs (7) (two are spares) Support rod holder Swing table end bracket Hinge pins (2) ...
-
Weber 900 LP - page 10
10 Figure 1 Step 2 Assemble wheel frame Y ou will need: wheel frame, two wheels, two wheel hubcaps, hammer and a block of wood. Set one end of wheel frame on the block of wood (or other hard, protected surface). Put one wheel on axle, WEBER side facing up, and tap on one hubcap. Figure 1. Repeat with other wheel and hubcap. W E B E R W E B E R Figu ...
-
Weber 900 LP - page 11
11 Figure 3 Step 4 Continue frame assembly Y ou will need: leg frame, wheel frame, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 inch wrench. Place the leg frame onto the tabs of the left frame with the dimple to the inside. Figure 3. Place the wheel frame onto the tabs of the right frame with the dimple to the inside. The fuel scale ...
-
Weber 900 LP - page 12
Y our Weber Gas Barbecue burner assembly has been factory assembled, pressure and flame tested. As a safety precaution we recommend you check the burner alignment: a) Do the valves fit into the ends of the burners? Figure 8 (a). b) Are the ends of the burners under the washers at the left rear and left front of the cooking box? The screws are only ...
-
Weber 900 LP - page 13
Frame brace Manifold bracket 13 Figure 9 Step 8 Install manifold bracket Y ou will need: manifold bracket Hook the bracket onto the manifold at the center burner valve. Figure 9. Place your hand underneath the bracket. Lift the manifold, bracket and cooking box slightly and hook the tab of the bracket onto the frame brace. Step 9 Install tank panel ...
-
Weber 900 LP - page 14
14 Step 10 Add fuel scale assembly Y ou will need: fuel scale assembly , two 1/4-20 wing nuts and two nylon washers. Slip the bolts on the back of the fuel scale assembly through the two small holes in the tank panel. Make sure indicator rod of fuel scale is on the left side of the wheel frame. Add washers then wing nuts and tighten. Figure 12. Fig ...
-
Weber 900 LP - page 15
15 Step 12 Set LP fuel scale Y ou will need: LP tank (empty). Note - F or accuracy , the fuel scale must be set with an empty tank. We utilize various LP tank manufacturers. Some of the tanks we receive have differing top collar assemblies. (The top collar is the metal protective ring around the valve.) One series of tanks mounts with the valve fac ...
-
Weber 900 LP - page 16
16 Route the hose so it will not interfere with the scale indicator rod. The hose and regulator are connected in the following manner: Slide back the collar of the quick disconnect on the tank valve. Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 17 (a). Figure 17 (b) shows t ...
-
Weber 900 LP - page 17
17 Step 16 Check for gas leaks Figure 18 D ANGER Do not use an open flame to check f or gas leaks. Be sure there are no sparks or open flames in the area while y ou check for leaks. This will result in a fire or explosion whic h can cause serious bodily injury or death and dama g e to property . Check: a) Hose to manifold connection. Figure 19 ...
-
Weber 900 LP - page 18
18 Step 17 Install Flavorizer Bars and Cooking Grates Y ou will need: five Flavorizer Bars and two cooking grates. Set the Flavorizer Bars side to side in the cooking box. Figure 20. Figure 20 Set the cooking grates onto the ledges in the cooking box. Figure 21. Figure 21 Step 18 Install the bottom tray Y ou will need: bottom tray , catch pan holde ...
-
Weber 900 LP - page 19
19 Step 19 Install Lid Y ou will need: lid, two hinge pins and two hair pin cotters. Set the lid in place. Align the hinges at the rear of the barbecue. Insert hinge pins from the outside. Insert hair pin cotters into the small holes in the hinge pins. Figure 25. Hair pin cotter Hinge pin Figure 25 Step 20 Add tool holders, control panel and burner ...
-
Weber 900 LP - page 20
20 Slot in frame (view from below) Insert one end of the hinge rod into the hole in the frame. Figure 28 (a). Insert the other end into the hole in the swing table end bracket. Figure 28 (b). Hold the end bracket at an angle so the lower tab is inside the frame tube. Push the bracket into the frame. Check to see that the lower tab of the bracket is ...
-
Weber 900 LP - page 21
21 Step 22 Complete accessory installation Y ou will need: work table, two accessory racks, warming rack, three tubing plugs and thermometer . Set the accessory rack across the bottom braces in front of the frame connector . Figure 29 (a). Set the second accessory rack across the bottom braces in the back of the frame connector . Figure 29 (b). Ope ...
-
Weber 900 LP - page 22
22 Lighting Summary lighting instructions are on the control panel. 1 3 2 4 7 6 5 8 Figure 1 Crosso ver Ignition System W ARNING: The burner contr ol knobs must be in the OFF position before turning on the LP tank v alve . If they are not in the OFF position, when y ou turn on the LP tank valve, the e xcess flow control will activ ate , limitin ...
-
Weber 900 LP - page 23
Manual Lighting 23 4) Turn the tank on by turning the tank valve counterclockwise. 5) Strike a match and put the flame into the matchlight hole in the front of the cooking box. W ARNING: Do not lean o ver open barbecue . K eep your face and bod y at least one foot a wa y from the matchlight hole when lighting the barbecue. 6) Push Front burner ...
-
Weber 900 LP - page 24
24 Cooking W ARNING: Do not move the W eber Gas Barbecue when operating or hot. Y ou can adjust the FRONT , CENTER and BACK burners as desired. The control settings High (H), Medium (M), Low (L), or Off (O) are described in your Weber cookbook. The cookbook uses these notations to describe the settings of the FRONT , CENTER, and BACK burners. F ...
-
Weber 900 LP - page 25
25 Cast Ir on Cooking Grates W ARNING: Follow all safety instructions pr o vided with your barbecue. Do not drop cast ir on grates, the y will break. Prior to storing, grease ver y lightl y with solid vegetable shor tening or vegetable cooking spray , then wipe dry with a paper towel. Store in a dr y place. First Time Use - W ash thoroughly wit ...
-
Weber 900 LP - page 26
26 26 Scale setting wing nut T ank lock wing nut T ank valve Collar (a) (b) Figure 3 Refilling the LP tank We recommend that you refill before the scale indicator reaches "E". Note - If you run out of fuel, chec k the indicator setting and/or adjust the fuel scale indicator setting with the scale setting wing nut, while the tank is empty ...
-
Weber 900 LP - page 27
27 27 c) Connect the hose to the tank. Route the hose so it does not interfere with the scale indicator rod. Slide back the collar of the quick disconnect on the tank valve. Figure 5 (a). Push the male fitting of the regulator into the quick disconnect, and maintain pressure. Slide the collar closed. Figure 5 (b). If it does not engage or lock, rep ...
-
Weber 900 LP - page 28
28 28 28 Safe handling tips f or LP Gas ■ Liquid Propane (LP) gas is a petroleum product as are gasoline and natural gas. LP gas is a gas at regular temperatures and pressures. Under moderate pressure, inside a cylinder , LP gas is a liquid. As the pressure is released the liquid readily vaporizes and becomes gas. ■ LP gas has an odor similar t ...
-
Weber 900 LP - page 29
29 29 Check: c) V alves to manifold connections. Figure 8 (c). d) The hose to regulator connection. Figure 8 (d). W ARNING: If there is a leak at connections (b), (c) or (d), turn OFF the gas . DO NO T OPERA TE THE B ARBECUE. Contact W eber-Stephen Customer Service . When leak checks are complete, turn gas supply OFF at the source and rinse con ...
-
Weber 900 LP - page 30
30 30 General Maintenance W eber Spider Stopper Guards Y our Weber Gas Barbecue, as well as any outdoor gas appliance, is a target for spiders and other insects. They can nest in the venturi section of the burner tubes. This blocks the normal gas flow , and can cause the gas to flow back out of the air shutter . Figure 9. This could result in a fir ...
-
Weber 900 LP - page 31
31 31 31 e) Remove the manifold bracket and unscrew the two wing nuts that hold the manifold to the cooking box. Pull the manifold and valve assembly out of the burners and carefully set it down. Figure 15. View from behind cooking box Wing nuts Figure 15 Guide screw Figure 16 Crossover tube Figure 17 i) Reinstall the Spider Stopper Guards. Slightl ...
-
Weber 900 LP - page 32
Crosso ver Ignition System Operations If the Crossover Ignition System fails to ignite the Front burner , light the Front burner with a match. If the Front burner lights with a match, then check the Crossover Ignition System. ■ Check that both the white and black ignition wires are attached properly . Figure 20. Figure 20 White wire Black wire ? ...
-
Weber 900 LP - page 33
33 33 Prob lem Burners b urn with a yellow or orange flame, in conjunction with the smell of gas. Burners do not light. -or - Burners ha ve a small flickering flame in the HIGH position. -or - Barbecue temperature only reaches 250˚ to 300˚ degrees in the HIGH position. Burner does not light, or flame is low in HIGH position. Experiencing flare-up ...
-
Weber 900 LP - page 34
34 W E B E R W E B E R ® ® ® ® ® ® ® ® 1 2 3 4 6 8 7 11-12 18 19 13 21 21 22 23 24 26 27 28 29 30 31 32 51-53 50 48 46 45 44 43 42 40 39 38 36 35 34 56-57 54 55 49 47 25 20 11 33 41 9 10 17 37 59 58 14 15 16 5 65 ...
-
Weber 900 LP - page 35
35 1 Lid (assembly) 2 Lid handle 3 W arming rack 4 Flavorizer bars (5) 5 Cooking grates (2) 6 Work table 7 T ubing plugs (7) 8 1/4-20 x 2 inch bolt 9 Swing table end bracket 10 Left frame 1 1 1/4-20 x 1/2 inch bolts (6) 12 1/4 inch nylon washers (1 1) 13 Leg frame 14 Swing table assembly 15 Support rod holder 16 Support rod 17 Bottom tray 18 Catch ...
-
Weber 900 LP - page 36
A F INAL W ORD OF T HANKS hank you for choosing a W eber Barbecue. Our family here at W eber has worked hard to produce the highest quality products for your satisfaction. While we give much attention to our products, an occasional error may occur . Our knowledgeable Customer Service staff is prepar ed to help you with any problems with parts or as ...
Do you have a question concerning Weber 900 LP?
Use the form below
If you did not solve your problem by using a manual Weber 900 LP, ask a question using the form below. If a user had a similar problem with Weber 900 LP it is likely that he will want to share the way to solve it.