-
Napco Security Technologies XP-400 - page 1
Usin g Y our XP-400 Security Sy stem NAPCO Oi220a page 1 Tuesday, September 16, 1997 08:30 ...
-
Napco Security Technologies XP-400 - page 2
2 Oi220a page 2 Tuesday, September 16, 1997 08:30 ...
-
Napco Security Technologies XP-400 - page 3
Introduction Congratulations on y our purc hase of an advanced NAPCO EXPRESS XP- 400 Security Sy stem. Meticulous ly developed by a leading manufac turer of state- of-the-art s ecurity products, this s y stem w ill provide y ou w ith unprecedented peace-of- mind & incorporates some of the most s ophisticated features available today . Above all ...
-
Napco Security Technologies XP-400 - page 4
4 1 Bell / Battery Test Test y our bell or siren by pressing followed by . This will caus e the bell, or siren to sound f or 2 seconds and also initiate a test of the battery . 2 Central Station Communication Test (This test should only be perform ed on weekends or at a time designated by y our alarm com pany) 1. Notify Central Station of the im pe ...
-
Napco Security Technologies XP-400 - page 5
Key pad Controls and Indi cator s Ready Light will light when all z ones are sec ure and system is r eady to be Armed. Zone Lights ( 1 through 4) will light to indicate that the corres ponding Zone is open, and will flash to indic ate a z one in alarm . A rmed Light will light when sy stem is Arm ed, and will flash when system is in Alarm Key - ...
-
Napco Security Technologies XP-400 - page 6
A rming Your Sy stem When Leaving 1 Before arm in g y our system, m ak e sure the Green Ready li g ht is ON. T his indicates that all of y our prot- ective zones are secur e. If any zones are open, the corres pondin g Zone li g ht will be ON. Secure these zones before proceedin g . If any z ones cannot be s ecured, see Bypassin g zones below. 2 Ent ...
-
Napco Security Technologies XP-400 - page 7
Protecting Yourself While at Home 1 Before ar min g y our system, m ak e sure the Green Ready li g ht is ON. T his indicates that all of y our protective zones are sec ure. If any z ones are open, the corr espondin g Zone li g ht will be ON. Secure those zones before proc eedin g . 2 Enter y our user code. T he Green Ready li g ht will g o out, and ...
-
Napco Security Technologies XP-400 - page 8
Emergency Buttons The two s ets of em ergency buttons, if pr ogramm ed, are always active whether the system is armed or disarm ed. Discuss these buttons with y our installer. The em ergency signal will only be activated when the two respective buttons ar e pressed at the sam e time. A uxiliary A larm: Simu ltaneously press + to alert the central s ...
-
Napco Security Technologies XP-400 - page 9
Disarming Your Sy stem when Returning 1 Enter y our prem ises throu g h the Entry/Exit door. The k ey pad will sound a steady tone to rem ind y ou to disarm the system befor e y our Entry Delay tim e expires. 2 Enter y our user code. T he Red Ar m ed li g ht will g o out, indicatin g that the system has been dis armed. Note: If you mak e a mistak e ...
-
Napco Security Technologies XP-400 - page 10
Special Functions By pressing follow ed by the appropriate key , (do not press simultaneously) these special functions and features can be enabled: Easy A rm ( w hen sy stem is disarm ed) The Easy Arm feature allows the system to be arm ed by pressing f ollowed by . This will allow the easy arm ing of the system by someone who is not a r egular ...
-
Napco Security Technologies XP-400 - page 11
Your Installer has ass igned a User 1 Code which may be used to not only Arm and Disarm the system, but also to enter the User Program Mode, where y ou can program and/or reprogram up to 4 User Codes. The following explains how you w ill use this c ode to program or erase additional user codes . Entering the User Program Mode Press followed by and ...
-
Napco Security Technologies XP-400 - page 12
The X P400 is constantly monitoring its own com ponents, as well as all c ritical services , such as AC Power and the Telephone line, to insure that it is alway s ready to provide the protection for which it was designed. W hen a sy stem trouble does occ ur, it will caution you by lighting the Yellow SYST EM light and beeping the keypad buzz er. If ...
-
Napco Security Technologies XP-400 - page 13
13 9 Sy stem Tr oubl es Keypad Beeps or SYSTEM Flashes Zone light ON System Tr ouble Condition Action 2 Beeps 1 Bell / Siren Trouble There is a problem w ith the Bell or Siren. Call installing com- pany for service. 2 Beeps 3 W ireless Receiv er Trouble A problem has been detected w ith the wireless receiv er. Call installing company for serv ic ...
-
Napco Security Technologies XP-400 - page 14
A mbush Code - In the event that y ou are for ced by an intruder to dis- arm y our system, this special code can be used to disarm the system, and sim ultane ously s end a s ilent alarm to Central Station. If y our sy s- tem has the Am bush f eature enabled, the code as signed as the User 4 code will function as your Am bush Code A rming / Disarmin ...
-
Napco Security Technologies XP-400 - page 15
15 Notes Oi220a page 15 Tuesday, September 16, 1997 08:30 ...
-
Napco Security Technologies XP-400 - page 16
NA PCO LIM I TED WA RRANTY THE FOLL OW ING STATEM ENT I S REQUIRED BY THE FCC . This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the m anufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to com ...
Do you have a question concerning Napco Security Technologies XP-400?
Use the form below
If you did not solve your problem by using a manual Napco Security Technologies XP-400, ask a question using the form below. If a user had a similar problem with Napco Security Technologies XP-400 it is likely that he will want to share the way to solve it.