English dropdown-ico

Manual Pelco DX8000-UPDVD

24 pages 5.84 mb
Download

Go to site of 24

Summary
  • Pelco DX8000-UPDVD - page 1

    DX8000-UPDVD Upgrade Installation Manual C1604M (6/04) Digital Video Recorder DX8000 ...

  • Pelco DX8000-UPDVD - page 2

    Protecting people and property in a million locations worldwide. ...

  • Pelco DX8000-UPDVD - page 3

    C1604M (6/04) 1 Introduction The following instructions serve as an installation guide for the DX8000-UPDVD drive kit. PARTS LIST NOTE: This upgrade kit includes a Pelco-certified DVD-RW drive. Using any other drive voids the manufacturer’ s warranty for the DX8000. Qty Description 1 DVD-RW drive 2 Mounting screws TOOLS NEEDED 1 Phillips-head scr ...

  • Pelco DX8000-UPDVD - page 4

    2 C1604M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools. Refer to the Parts List and T ools Needed section. 3. Shut down the DX8000 Series DVR unit. Refer to DX8000 Installation Manual or Operations and Programming Manual for instructions on shuttin ...

  • Pelco DX8000-UPDVD - page 5

    C1604M (6/04) 3 Figure 2. Removing Power Cord from Unit ...

  • Pelco DX8000-UPDVD - page 6

    4 C1604M (6/04) Figure 3. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective m ...

  • Pelco DX8000-UPDVD - page 7

    C1604M (6/04) 5 Prepare Unit for Drive Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components. 1. If the DX8000 is mounted in a rack, remove it and transport it to an area that will provide full access to the u ...

  • Pelco DX8000-UPDVD - page 8

    6 C1604M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section. a. Remove the two top-most screws on the left and right side panels of the DX8000. Ref ...

  • Pelco DX8000-UPDVD - page 9

    C1604M (6/04) 7 4. Using a Phillips-head screwdriver , remove the side panel from the side of the unit closest to the CD/DVD drive: a. Remove the four screws from the side panel. Refer to Figure 5. b. Set the panel and screws aside for use later . Figure 5. Removing Side Panel ...

  • Pelco DX8000-UPDVD - page 10

    8 C1604M (6/04) COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity . POWER SUPPLY DIMM SOCKETS (RAM) CPU VGA CARD PCI SLOT 1 2 3 4 5 6 REAR CROSS-BRACE FRONT CROSS-BRACE MOTHERBOARD IDE CONNECT ...

  • Pelco DX8000-UPDVD - page 11

    C1604M (6/04) 9 Remove the Existing Optical Drive DISCONNECT THE CD/DVD DA T A CABLE AND POWER WIRES When removing data cable and power wires, pull the connectors straight out. Do not rock connectors back and forth or remove a connector by pulling it by its wires or cable. 1. Remove the IDE data cable from the existing CD/DVD by carefully pulling t ...

  • Pelco DX8000-UPDVD - page 12

    10 C1604M (6/04) 2. Remove the power connector from the CD/DVD drive. Refer to Figure 8. 2 Figure 8. Removing the CD/DVD Power Connector ...

  • Pelco DX8000-UPDVD - page 13

    C1604M (6/04) 11 REMOVE THE CD/DVD DRIVE 1. Using a Phillips-head screwdriver , unfasten the two screws that attach the CD/DVD to the chassis. Refer to Figure 9. Figure 9. Removing CD/DVD Mounting Screws 1 ...

  • Pelco DX8000-UPDVD - page 14

    12 C1604M (6/04) 2. Gently pull the CD/DVD drive out of the DVR through the front of the unit. Refer to Figure 10. 2 Figure 10. Removing the Existing Optical Drive ...

  • Pelco DX8000-UPDVD - page 15

    C1604M (6/04) 13 Install the New DVD-RW Drive into the Unit 1. Insert the new DVD-RW into the DVR: a. Make sure the drive is oriented correctly . b. Insert the new DVD-RW into the DVR through the front of the unit. Refer to Figure 11. Figure 11. Inserting the New DVD-RW Drive 1b DVD-RW ...

  • Pelco DX8000-UPDVD - page 16

    14 C1604M (6/04) c. Using a Phillips-head screwdriver and the two screws provided in the upgrade kit, secure the drive to the unit’ s chassis. Refer to Figure 12. T ighten the screws securely but do not over-tighten. Figure 12. Securing the New DVD-RW Drive 1c ...

  • Pelco DX8000-UPDVD - page 17

    C1604M (6/04) 15 RECONNECT THE DA T A CABLE AND POWER WIRES IMPORT ANT : Data and power connectors fit together only one way . All connectors are keyed to ensure that they are inserted in the proper orientation. Examine the drive, motherboard and cable connectors before installation so that connectors are properly aligned. Make sure connectors are ...

  • Pelco DX8000-UPDVD - page 18

    16 C1604M (6/04) 2. Connect the DVD-RW drive to the system motherboard using the existing data cable. Refer to Figure 14. 2 Figure 14. Installing DVD-RW Data Cable ...

  • Pelco DX8000-UPDVD - page 19

    C1604M (6/04) 17 Reassemble the Unit 1. Using a Phillips-head screwdriver , reattach the side panel you removed earlier . Refer to Figure 15. Figure 15. Replacing Side Panel ...

  • Pelco DX8000-UPDVD - page 20

    18 C1604M (6/04) 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 16. Figure 16. Replacing Chassis Cover ...

  • Pelco DX8000-UPDVD - page 21

    C1604M (6/04) 19 4. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 3. Plug the power cord back into the power supply and then into the wall. 4. T urn on the power switch and allow the unit to start up and find the new DVD-RW . This may take several minutes. ON/OFF F ...

  • Pelco DX8000-UPDVD - page 22

    20 C1604M (6/04) Notes ...

  • Pelco DX8000-UPDVD - page 23

    PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models ...

  • Pelco DX8000-UPDVD - page 24

    Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. Windows is a registered trademark of Microsoft Corporation. C1604M (6/04) W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/ ...

Manufacturer Pelco Category DVR

Documents that we receive from a manufacturer of a Pelco DX8000-UPDVD can be divided into several groups. They are, among others:
- Pelco technical drawings
- DX8000-UPDVD manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco DX8000-UPDVD
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco DX8000-UPDVD.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco DX8000-UPDVD, service manual, brief instructions and user manuals Pelco DX8000-UPDVD. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco DX8000-UPDVD.

Similar manuals

A complete manual for the device Pelco DX8000-UPDVD, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco DX8000-UPDVD by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco DX8000-UPDVD.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco DX8000-UPDVD - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco DX8000-UPDVD, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco DX8000-UPDVD, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco DX8000-UPDVD - which should help us in our first steps of using Pelco DX8000-UPDVD
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco DX8000-UPDVD
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco DX8000-UPDVD in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco DX8000-UPDVD?

Use the form below

If you did not solve your problem by using a manual Pelco DX8000-UPDVD, ask a question using the form below. If a user had a similar problem with Pelco DX8000-UPDVD it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)